Image Engineering TE292 Manual de usuario

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Instrumento de medición de Image Engineering

Image Engineering

Image Engineering camSPECS Manual de usuario

Image Engineering

Image Engineering LED-Panel V4 Manual de usuario

Image Engineering

Image Engineering CAL4-E Manual de usuario

Image Engineering

Image Engineering iQ-FoV Box Manual de usuario

Image Engineering

Image Engineering GEOCAL Manual de usuario

Image Engineering

Image Engineering camSPECS Manual de usuario

Image Engineering

Image Engineering LED-Panel V5 Manual de usuario

Image Engineering

Image Engineering TE292 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Image Engineering GmbH & Co. KG · Im Gleisdreieck 5 ·50169 Kerpen-Horrem ·Germany

T +49 2234 2273 99 99 1-0 ·F +49 2234 2273 99 99 1-10 · www.image-engineering.com

TE292 + TE292 VIS-IR

User Manual

12. April 2022

Image Engineering GmbH & Co. KG · Im Gleisdreieck 5 ·50169 Kerpen-Horrem ·Germany

T +49 2234 2273 99 99 1-0 ·F +49 2234 2273 99 99 1-10 · www.image-engineering.com

1 INTRODUCTION

Important information: Read the manual carefully before using the device. Inappropriate utilization

may cause damage to the device. Keep these instructions in a safe place and pass them to any

future user.

The TE292 and TE292 VIS-IR filter plates are intended for use with the Image Engineering LE7 or

LE7 VIS-IR illumination device, iQ-LED software, and the camSPECS software. Refer to the user

manuals for each of these products for detailed operating instructions.

The TE292 and TE292 VIS-IR bundle includes the filter plate, calibration plate, and calibration plate

thumb nut.

2 OPERATING INSTRUCTIONS

1. Remove the packaging material and insert the TE292 or TE292 VIS-IR into the test chart holder

of the LE7 or LE7 VIS-IR as pictured:

2. Power up the LE7 or LE7 VIS-IR and connect the USB cable between the device and the host

computer.

3. Using the iQ-LED software, create an E illuminant at near full power and save to the device as

described in the iQ-LED user manual.

4. Disconnect the device USB cable.

5. Connect the EX2 spectrometer calibrator USB cable between the host computer.

6. From the control panel on the device, select the E illuminant saved to the device earlier.

7. Launch the camSPECS software and perform the calibration as described in the camSPECS

user manual.

8. To perform camera spectral sensitivity measurements, proceed as described. The camera

exposure will depart from the typical settings suggested and should be optimized as described in

the camSPECS user manual.

Image Engineering GmbH & Co. KG · Im Gleisdreieck 5 ·50169 Kerpen-Horrem ·Germany

T +49 2234 2273 99 99 1-0 ·F +49 2234 2273 99 99 1-10 · www.image-engineering.com

3 MAINTENANCE

TE292 and TE292 VIS-IR do not need any special maintenance, however:

•Do not touch or pollute the surfaces of the filters.

•Remove dust on the filters with pressurized-air spray.

•Remove undesired fingerprints or oils on the filters carefully with a soft and dry tissue