Ikelite 6801.32 Manual de usuario

Thank you for your purchase of Ikelite equipment. Please read this

instruction manual completely before attempting to operate or dive

with this product. Please refer to the back page of this manual to

Port Lock

IKELITE

SLR-DC ousing

instruction manual

6801.32 for the ikon D3200

Table of Contents

Specifications ..............................................................P. 3

Package Contents ........................................................P. 4

Preparation ..................................................................P. 4

Attach External “Tray with andles” to ousing ............P. 4

Parts of the ousing - Front/Side View ..........................P. 5

Parts of the ousing - Back View ..................................P. 6

Initial Camera Setup........................................................P. 7

Opening the ousing ......................................................P. 7

ousing Conversion Circuitry..........................................P. 8

Setting the Conversion Circuitry Strobe ID Switch..........P. 8

Using the Conversion Circuitry........................................P. 9

Flash Mode and Compensation Dial ..............................P. 9

Using Non-Ikelite or Ikelite Non-DS Substrobes ............P. 9

DS50 and DS125 Substrobe Compatibility ....................P. 10

Attaching the Flash Connection for External Strobes ....P. 10

Attach Camera to ousing Tray......................................P. 11

Installing Camera in ousing ..........................................P. 11

Closing the ousing ........................................................P. 12

Final Check ....................................................................P. 12

Attaching a S ync Cord to the ousing ............................P. 13

Turn Camera On..............................................................P. 13

Zoom Clamp & Gear Sleeve Installation ........................P. 14

Manual Focusing ............................................................P. 18

Installing the Port ............................................................P. 19

Lens Ports ......................................................................P. 20

Attaching an Ikelite Strobe Arm to the ousing andle..P. 21

Table of Contents - continued

Usage ............................................................................P. 22

Pre-Dive Your System ....................................................P. 22

Lubricants ........................................................................P. 22

Troubleshooting ........................................................P. 23

Recommended Accessories ....................................P. 25

Accessory Mounting Points ............................................P. 25

EV-Controller Use............................................................P. 25

Maintenance..................................................................P. 26

Storing the ousing ........................................................P. 29

Spare Parts ..................................................................P. 29

Photo Tips ....................................................................P. 29

Technical Support ........................................................P. 30

Limited Warranty ........................................................P. 31

Returning Products for Service ................................P. 31

Product Registration ..................................................Back Cover

Specifications

- Controls ............All camera functions are accessible except the Diopter

..........................Adjustment Control

- Width ................9.6in (244mm) including controls

- eight ..............6.9in (175mm) including controls

- Depth ................6.5in (165mm) including controls

- Weight ..............5.5lb (2495g) without tray & handles

- Buoyancy ..........Slightly negative in freshwater

- Depth Rating ....200ft (60m)

- Built-in Flash ....Not accessible

- Tray Mounting ..12-24 thread with 3in spacing (76mm)

- SLR-DC ousing

- Envelope containing tray

installation hardware,

maintenance kit, and extra

control end tips.

Package Contents

- Aluminum Tray & Dual andles

- Silicone Lubricant

- Standard Zoom Clamp & Sleeve Set

- #5509.28 Large Diameter Zoom

Clamp & Sleeve Set

This product has been water pressure tested at the factory and is depth

rated to 200 ft. (60m). Thoroughly inspect and immerse the empty

housing completely in water before installing a camera. If any fogging

occurs or droplets of water enter the housing, do not install a camera.

Clean the housing main o-ring and retest to make sure that it is

watertight. Refer to the Troubleshooting section, page 23.

We suggest that you read this instruction booklet thoroughly before use

to have a full understanding of where each camera control is located,

and what function each control provides. Please read your camera

manual thoroughly to have a full understanding of each camera function.

If you are new to underwater photography, be sure to read the Photo

Tips section.

Due to the power required to operate the camera and LCD screen start

each dive with a fully charged camera battery.

Preparation

Attach External “Tray with Handles” to Housing

Use hardware and instructions located in the clear Ikelite pouch to attach

the “Tray with andles” to your Ikelite housing.

Port Lock

IKELITE

Parts of the Housing - Front View

Flash Mode

Quick Release

Strobe Arm

Mount

andle

Port

Opening

Gear Sleeve

Drive Gear

Shutter

Release

Aperture Button/

AE-L/AF-L

Lid

Snap

Side View

Gear

Sleeve

Optional

Port

Port O-ring

Main ousing

O-ring

Camera Tray

Camera Mounting Bolt

Aluminum Tray

Zoom

Leveling Screw (Factory Pre-set)

Shutter

Release

Power Switch Mode Dial

Port Lock

Movie-record

Button

TTL

-1

-2

-3

MAN

11 12 13

Back View

Lens

Release

Button

Quick

Release

Button

1. External Strobe Connector and

Waterproof Cap

2. Playback

3. ME U Button

4. Playback Zoom In

5. Playback Zoom Out

6. Information Edit Button

7. Super-eye Viewfinder Port

8. Command Dial

9. Lv Live-view Button

10. Multi-Selector Up

11. Multi Selector Left

12. OK Button

13. Multi Selector Right

14. Multi Selector Down

15. Release Mode

16. Flash Exposure Control Dial

17. Delete Button

Function

Button

Information Button

Opening the Housing

Lid Snaps have a Lock. To open,

push Lid Snap Lock forward and lift as

shown. Keep pressure on the Lid

Snap so it does not fly open quickly.

Lid Snaps have a lot of spring tension

once they go over center, so have a

firm grip on the Lid Snap. Lid Snaps

may be opened one at a time.

Lift

Push Forward

Lid Snap Lock

Initial Camera Setup

- Insert a fully charged battery.

- Insert a SD or SD C memory card.

- Set the mode dial to “M” manual.

- Set Time Zone and Date.

- Set shutter speed to 1/60th second or 1/125th second for fast

moving subjects.

- Set aperture to F8 for general photography or F22 for macro

photography (close-ups).

- Set Image Quality to Fine or RAW.

- Set Image Size to “L” Large.

- Set White Balance to “Auto” and ISO sensitivity setting to “100.”

- Set Active D-Lighting to “Off.”

- Set Auto Distortion Control to “On.”

- Set Noise Reduction to “On.”

- Set AF-area mode Viewfinder to “Single-point AF” and Live-view/movie

to “Normal-area AF.”

- Set Built-in AF-assist illuminator to”Off.”

- Set Metering to “Center-weighted metering.”

ote: This housing is designed for use with an external strobe. The

camera’s internal flash cannot be used while in the housing. Make sure

Red-eye reduction is off when connected to a strobe.

On the bottom of the internal housing tray is a switch for setting the DS

Substrobe ID. Set the switch to the Model of DS Substrobe being used.

When using dual strobes of different models such as a DS51 and a

DS161, set the ID switch to DS51 or the smaller strobe.

Set

DS Substrobe

to TTL Mode

50-51

TIGHTEN HOLDOWN BOLT

WITH COIN

OR SCREWDRIVER

160-161

125-200

Setting the Conversion Circuitry Strobe ID Switch

Strobe ID

Switch

Housing Conversion Circuitry

This housing contains Ikelite designed and patented Conversion

Circuitry. Once attached, turn the strobe on first before turning on the

camera.

When used with Ikelite DS Substrobes the Conversion Circuitry provides

real Nikon iTTL flash exposure with over and underexposure

compensation from +1 1/3 to - 1 1/3 f-stops in 1/3 stop increments.

The Conversion Circuitry also offers Manual exposure control with 3 1/2

f-stops of underexposure control in 1/2 stop increments.

The Conversion Circuitry is powered by the Ikelite DS Substrobe when

connected to the housing with the 4103.51 single or 4103.52 dual sync

cord. When using two strobes with the dual sync cord, the primary

strobe connected to the cord without the red band, must be turned on to

power the Conversion Circuitry. Always keep both strobes connected to

your dual sync cord underwater. Do not exchange your secondary

strobe for a dust cap which may not be waterproof.

Using the Conversion Circuitry (Set DS Substrobe to TTL mode)

-Mode and Compensation Dial (see illustration below)

Note that the TTL compensation values are located in the yellow band.

Manual compensation values are located in the black band. Rotate the

Dial to switch between TTL and Manual Modes.

-TTL Mode compensation values are indicated in the yellow band. Place

the Setting Indicator to TTL for O Compensation. Rotate the Dial either

direction to select +/- compensation. Place the Setting Indicator to the

desired compensation value. Note that in TTL, compensation values are

in 1/3 f-stops.

-Manual Mode compensation values are indicated in the black band.

Rotate the Dial to place the Setting Indicator to the desired compensation

value. Note that in Manual Mode, compensation values are in 1/2 f-stops

from (F) full power to -3 f-stops.

Set DS Substrobe to TTL mode. This will allow the strobe power to

be varied in manual mode.

Setting Indicator

DIAL

TTL Flash Scale (yellow = 1/3 stops)

Manual Flash Scale (black = 1/2 stops)

Flash Mode and Compensation Dial

Using on-Ikelite or Ikelite on-DS Substrobes

(Substrobe 50, 100A, 200, 400) with this Housing

The Conversion Circuitry is automatically disabled when used with a

Non-Ikelite or Non-DS Substrobe. These Substrobes can be used in their

manual mode utilizing any power settings provided on the Substrobe.

DS50 and DS125 Substrobe Compatibility

- Older DS50 Substrobes with Serial Number below 63,850 can NOT be

updated to operate correctly with the latest TTL conversion circuitry.

Older DS50 Substrobes with Serial Number between 63,850 and 69,999

require upgrade of electronics to operate. Cost of update depends on

strobe circuitry. Strobe must be returned to Ikelite for evaluation to

provide an estimate of upgrade cost.

- Older DS125 Substrobes with Serial Number below 2,500 can NOT be

updated to operate correctly with the latest TTL conversion circuitry.

Older DS125 SubStrobes with Serial Number between 2,500 and 4,999

require upgrade of electronics to operate. Cost of update depends on

strobe circuitry. Strobe must be returned to Ikelite for evaluation to

provide an estimate of upgrade cost.

Attaching the Flash Connection for External Strobes

When using an external

strobe, connect the

housing hotshoe connector.

Slide the connector into the

hotshoe mount on the

camera from the back of

the camera as shown.

Slide the connector forward

until it stops. Due to limited

clearance between the

camera hotshoe mount and

the housing back, the

hotshoe connector should

be attached before the

camera is secured with the

mounting bolt.

Front

Ikelite

External Strobe Connector

and Waterproof Cap

ousing Back

otshoe

Connector

Tabla de contenidos

Otros manuales de Accesorios para cámaras de Ikelite

Ikelite

Ikelite 6242.62 Manual de usuario

Ikelite

Ikelite 6182.50 Manual de usuario

Ikelite

Ikelite FinePix F50fd Manual de operación y mantenimiento

Ikelite

Ikelite 6140.21 Manual de usuario

Ikelite

Ikelite 200DLM Manual de usuario

Ikelite

Ikelite Olympus Mju760 Manual de usuario

Ikelite

Ikelite Nikon D200 Manual de usuario

Ikelite

Ikelite Nikon S200 Manual de usuario

Ikelite

Ikelite 6184.99 Manual de usuario

Ikelite

Ikelite 6110.93 Manual de usuario

Ikelite

Ikelite 6214.08 Sony DSC-WX80 Manual del propietario

Ikelite

Ikelite DLM200 Manual de usuario

Ikelite

Ikelite 6871.06 Manual de usuario

Ikelite

Ikelite 6891.1 Manual de usuario

Ikelite

Ikelite ULTRAcompact 6270.25 Manual de usuario

Ikelite

Ikelite DSC-H3 Manual de usuario

Ikelite

Ikelite SD-750 Manual de usuario

Ikelite

Ikelite SLR-DC Housing Manual de usuario

Ikelite

Ikelite 5510.35 Manual de usuario

Ikelite

Ikelite 6843.72 Manual de usuario

Ikelite

Ikelite EOS 5D Mark II - EOS 5D Mark II 21.1MP Full Frame CMOS Digital SLR... Manual de usuario

Ikelite

Ikelite 5650 Manual de usuario

Ikelite

Ikelite SLR-DC Housing Manual de usuario

Ikelite

Ikelite Canon PowerShot A700 Manual de usuario

Manuales populares de Accesorios para cámaras de otras marcas

Viltrox

Viltrox EF-NEX Instrucciones de instalación

Calumet

Calumet 7100 Series CK7114 Manual de usuario

Ropox

Ropox 4Single Series Manual de usuario

Cambo

Cambo Wide DS Digital Series Instrucciones de funcionamiento

Samsung

Samsung SHG-120 Manual de usuario

Ryobi

Ryobi BPL-1820 Manual de operación

Aegis

Aegis ABL-36020P Manual de usuario

Pentax

Pentax Data Back Fc Manual de usuario

Fantasea

Fantasea EyeGrabber F Series Manual de usuario

Honeywell

Honeywell HDZ20HD Manual de usuario

EGO

EGO BA1400T Manual de usuario

Sima

Sima SRW-62 Manual de usuario

Shape

Shape A7SSMKIT Manual de usuario

Slide Kamera

Slide Kamera HST-2 Manual de usuario

Power works

Power works 2902613 Manual de usuario

SES

SES SE-2047-2 Manual de usuario

Olympus

Olympus PT-EP05L Manual de usuario

Starlite

Starlite OctoDome nxt Manual de usuario