Ikan PT4900S-PEDESTAL Manual de usuario

www.ikancorp.com | 1.713.272.8822 | [email protected]

PT4900S-PEDESTAL

Quick Start Guide

19” SDI Teleprompter, Pedestal & Dolly Turnkey

OVERVIEW

Ikan’s Turnkey Broadcast Solutions include everything you need for your professional camera setup. This solution includes a 19” teleprompter,

pedestal, and dolly. All of our systems have been tested internally for payload compatibility.

The remaining payload capacity, after mounting the full 19” teleprompter, can accommodate camera setups up to 38.8 lbs. The pedestal,

without the teleprompter system, can accommodate cameras up to 61.7 lbs. This solution also includes a hard case for the pedestal and a

carrying bag for the dolly.

www.ikancorp.com | 1.713.272.8822 | [email protected]

What’s Included

Large Riser

Bottom Plate

Hood Attachment Frame

Glass Frame Screws 15mm Rod Clamps 15mm Rods Large Riser

Bracket

Glass Holder Hood

Glass

Medium Riser

Base

DSLR/Mirrorless Riser

Glass Frame Holder Bracket

w/ Rod Clamps

PT4900-SDI

19” Professional High Bright Beam Splitter Teleprompter with 3G-SDI

www.ikancorp.com | 1.713.272.8822 | [email protected]

Teleprompter Assmebly Setup

Step 1

Place the Hood Attachment Frame over the Glass Holder. Then place the

glass against the Glass Holder. Make sure the screws pass through the

holes on the both the Hood Attachment Frame and the Glass Holder.

Step 3

Remove the monitor mounts from the teleprompter base using

the included larger 4mm hex key to loosen from the 15mm rods.

Step 4

Put the washers on before tightening the screws. The washers and 4

additional screws are inside a bag on the bottom foam.

Step 2

Secure the Glass Holder by fastening the knurled nuts to the screws as

pictured below.

www.ikancorp.com | 1.713.272.8822 | [email protected]

Step 5

After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket.

Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor.

*SAFETY NOTE* Make sure to leave at least 2 inches of the rods inside the teleprompter base.

Teleprompter Base

Step 6

While sliding the teleprompter bracket into the slot of the Glass Frame

Holder Bracket, pull on the red knob to allow the bracket to fully slide in.

Step 7

Once the bracket is in place, tighten the side screw to lock in place.

Double check and make sure all the screws are tightened with the

included hex keys.

www.ikancorp.com | 1.713.272.8822 | [email protected]

Step 9

To prevent light from leaking through the hood, seal both zippers down.

Step 8

Fold the ﬂaps of the Hood alongside the edges of the Hood Attachment Frame. The ﬂaps of the Hood are magnetic so they will automatically attach.

www.ikancorp.com | 1.713.272.8822 | [email protected]

Step 10

Slide in the Riser plate of your choice by aligning the screws on the riser plate to the slot on the Base. Once the screws are aligned, Slide the riser plate into

the Base.

Step 10

Slide in the Riser plate of your choice by aligning the screws on the riser plate to the slot on the Base. Once the screws are aligned, Slide the riser plate into

the Base.

www.ikancorp.com | 1.713.272.8822 | [email protected]

Step 12

Mount your own tripod plate to the bottom plate by aligning the 1/4-20 and/or 3/8-16 screws and fastening them to the Bottom Plate. It is recommended

that you connect your tripod plate to front of the Bottom Plate so that you can balance your teleprompter easier. Once your tripod plate is connected to the

Bottom Plate, mount the tripod plate to your tripod head.

Step 13

Slide the entire teleprompter system into the Bottom Plate. Once the

teleprompter system is inserted, you can balance it by sliding it along the

Bottom Plate until the center of gravity is determined.

Step 14

Once the center of gravity has been determined, tighten the thumb screws

to keep the base from sliding.

www.ikancorp.com | 1.713.272.8822 | [email protected]

Step 15

To secure your teleprompter system, insert the included headless screws into the threads behind and in front of the Base.

Step 16

The headless screws should be inserted to the threads as pictured below.

www.ikancorp.com | 1.713.272.8822 | [email protected]

Monitor Ports

3G-SDI – Serial Digital Interface Connection

VGA – Video Graphics Array DE15 Connection

HDMI – High-Deﬁnition Multimedia Interface Input Connection

Power Port – 12-24v Input

HDMI – Switch HDMI input

VGA – Switch to VGA input

SDI – Switch to 3G-SDI input

Flip – Toggle image ﬂip

(Can be set to horizontal, vertical, or both via menu)

Up Arrow – Toggle up to adjust setting

Menu – Access to monitor settings

Down Arrow – Toggle down to adjust setting

Monitor Menu Settings

Video Conﬁg

Contrast (White Level)

Brightness (Black Level)

Tint (Chroma Hue)

Chroma (Chroma Saturation)

Sharpness (Detail)

RGB Setup – Manually conﬁgure RGB

Return

System Conﬁg

Menu Duration – Set duration of how long menu stays

on screen

Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is

native resolution, 16:9 will create black bars)

Flip-H – Assign toggle button to ﬂip image horizontally

Flip-V – Assign toggle button to ﬂip image vertically

Reset – Factory reset

Return

PC Setup (Only available for VGA)

H-Position – Adjust horizontal position

V-Position – Adjust vertical position

Auto – Monitor automatically adjust position

Return

Exit

How to set-up FLIP button feature:

1. Press MENU button

2. Navigate to SYSTEM CONFIG.

3. Navigate to FLIP-V or FLIP-H

4. Change FLIP-V and/or FLIP-H to “ON”

5. Exit MENU

6. The FLIP button should now be activated and can be

pressed to mirror the image Horizontally or Vertically

7. When FLIP-H is ON, the image will ﬂip Horizontally

8. When FLIP-V is ON, the image will ﬂip Vertically

9. If both are ON, the FLIP button will toggle both

Horizontal and Vertical ﬂip

www.ikancorp.com | 1.713.272.8822 | [email protected]

Speciﬁcations

PT4900-SDI

Optional Accessories

PT4900-GM

PT19-SDI-TM

PT-PEDAL

PT-CASE-V2

Replacement Glass for PT4900

19” 3G-SDI Talent Monitor Add On Kit for PT4900

Teleprompter Foot Control Pedal

Rolling Hard Case for PT4900 Teleprompter

Aspect Ratio 4:3

Backlight LED

Brightness 1000 nits

Build Material Aluminum Chassis

Diagonal 19”

Input Signal 3G-SDI, HDMI, and VGA inputs

Input Voltage DC 12v / 4A

Power Consumption 10W

Reading Range 25’

Resolution 1280 x 1024

Viewing Angle 160° (H) / 170° (V)

Weight 33.75 lbs

Shipping Weight 36 lbs

Shipping Dimensions 25 x 20 x 16 in

Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Telepromopters:

https://youtube.com/playlist?list=PLcjaK5n9Y8ctrbYS3t2g4nyx2uADOXjuF

Tabla de contenidos

Otros manuales de Accesorios para cámaras de Ikan

Ikan

Ikan ELE-TRIFLY Manual de usuario

Ikan

Ikan ELE-USB-DRGFLY Manual de usuario

Ikan

Ikan PT4500-PEDESTAL Manual de usuario

Ikan

Ikan PSB10 Manual de usuario

Ikan

Ikan MOTUS22 Manual de usuario

Ikan

Ikan HB160-GC Manual de usuario

Ikan

Ikan TRD Beholder MS1 Manual de usuario

Ikan

Ikan D5-K1-N Manual de usuario

Ikan

Ikan ID 500 Manual de usuario

Ikan

Ikan PT4700-PEDESTAL Manual de usuario

Ikan

Ikan Saga SX7 Manual de usuario

Ikan

Ikan STR-CINE-C500-RIG Manual de usuario

Ikan

Ikan PT4900-PEDESTAL Manual de usuario

Ikan

Ikan BMC-PBK-QR Manual de usuario

Ikan

Ikan ELEMENTS DELUXE FLY Manual de usuario

Ikan

Ikan PSB5 Manual de usuario

Ikan

Ikan beholder EC1 Manual de usuario

Ikan

Ikan PT4500-SDI-P2P-TK Manual de usuario

Ikan

Ikan PT4900-SDI-P2P-TK Manual de usuario

Ikan

Ikan iLED-MA Manual de usuario

Ikan

Ikan PD1 Manual de usuario

Ikan

Ikan IFD576-KIT-CH Manual de usuario

Ikan

Ikan PT4500-SDI-P2P Manual de usuario

Ikan

Ikan TRD Beholder MS1 Manual de usuario

Manuales populares de Accesorios para cámaras de otras marcas

Viltrox

Viltrox EF-NEX Instrucciones de instalación

Calumet

Calumet 7100 Series CK7114 Manual de usuario

Ropox

Ropox 4Single Series Manual de usuario

Cambo

Cambo Wide DS Digital Series Instrucciones de funcionamiento

Samsung

Samsung SHG-120 Manual de usuario

Ryobi

Ryobi BPL-1820 Manual de operación

Aegis

Aegis ABL-36020P Manual de usuario

Pentax

Pentax Data Back Fc Manual de usuario

Fantasea

Fantasea EyeGrabber F Series Manual de usuario

Honeywell

Honeywell HDZ20HD Manual de usuario

EGO

EGO BA1400T Manual de usuario

Sima

Sima SRW-62 Manual de usuario

Shape

Shape A7SSMKIT Manual de usuario

Slide Kamera

Slide Kamera HST-2 Manual de usuario

Power works

Power works 2902613 Manual de usuario

SES

SES SE-2047-2 Manual de usuario

Olympus

Olympus PT-EP05L Manual de usuario

Starlite

Starlite OctoDome nxt Manual de usuario