IKA Lab disc Manual de usuario

102009

Reg.No. 4343-01

39 058 00

IKA

lab disc

•

Use only the AC adapter supplied

• Set up the appliance in a specious area on an even, stable,

clean, non-slip, dry and fireproof surface.

• The base plate must be clean and intact.

• Check the appliance and accessories before hand for dama-

ge each time you use them. Do not use damaged compo-

nents.

• Reduce the speed if

- the m

edium splashes out of the vessel because the speed

is too high

- the appliance is not running smoothly

- the container moves on the base plate.

• Beware of hazards due to:

- flammable materials

- combustible media with a low boiling temperature

- incorrect container size

- overfilling of media

- unsafe condition of container.

• The appliance may heat up when in use.

• Process pathogenic materials only in closed vessels under a

suitable extractor hood. Please contact IKA if you have a

questions.

• Do not operate the appliance in explosive atmospheres,

with hazardous substances or under water.

• Only process media that will not react dangerously to the

extra energy produced through processing. This also applies

to any extra energy produced in other ways, e.g. through

light irradiation.

• Safe operation is only guaranteed with the accessories

described in the “Accessories” chapter.

• The centre of gravity of the assembly must lie within

the surface on which it is set up.

Page

Safety instructions 8

Operator’s control 9

Unpacking 9

Correct use 9

Installation 10

Maintenance 10

Accessories 10

Warranty 10

Technical data 11

For your protection

•

Read the operating instructions in full before starting

up and follow the safety instructions.

• Keep the operating instructions in a place where they can

be accessed by everyone.

• Ensure that only trained staff work with the appliance.

• Follow the safety instructions, guidelines, occupatinal

health and savety and accident prevention regulations.

• Caution - Magnetism! Effects of the magnetic field have

to be taken into account (e.g. data storage media, cardiac

pacemakers ...).

• Wear your personal protective equipment in accordance

with the hazard category of the media to be processed.

Otherwise there is a risk from:

- splashing and evaporation of liquids

- ejection of parts

- release of toxic or combustable gases.

Contents

Safety instructions

• The appliance must only be disconnected from the mains

supply by pulling out the plug-in power supply unit.

• The socket for the the plug-in power supply unit must be

easely accessible.

• The appliance starts up again atomatically following a cut in

the power supply.

• Abrasion of the dispersion equipment or the rotating acces-

sories can get into the medium you are working on.

• Whem using the PTFE-coated magnetic bars, the following

has to be noted:

Chemical reactions of PTFE occur in con-

tact with molten or dissolved alkaline and alkaline-earth

metals, as well as with fineparticeld powders of metals of

the 2. and 3. group of the periodical system at temperatures

above 300-400 °C. Only elementary fluorine, chlorine trifluo-

ride and alkaline metals do attack PTFE, halogen hydrocar-

bons have a reversible swelling effect.

(Source: Römpps Chemie-Lexikon and „Ullmann“ Bd.19)

To the protection of the equipment

Caution: Equipment may not be poured over with

aggressive media! Equipment never under water set!

• The voltage stated on the nameplate must correspond to

the mains voltage.

• Do not cover the device, even partially e.g. with metallic

plates or film. This results in overheating.

• Protect the appliance and accessories from bumps and

impacts.

• Ensure that the base plate is kept clean.

Operator’s control

• Unpacking

- Please unpack the device carefully

- Inthe case of any damage a fact report must be set

immediately (post, rail or forwarder)

• Delivery scope

- Magnetic stirrer

- Plug-in power supply

- Operating instruction

• Use

- for mixing liquids

• Range of use

- Laboratories - Schools

- Pharmacies

Unpacking

Correct use

key

key -

LED 1 LED 2

key

key +

- Connect the appliance to a socket (the voltage stated

on the nameplate must correspond to the mains volta-

ge).

- Number of revolutions to minimum value set

(switch on with , with reduce number

of revolutions to LED 2 permanently shines)

- Place a magnetic rod in a vessel which is penetrable

for magnetic field lines and fill the vessel with the

medium to be processed.

- Place the vessel on the centre of the set-up surface.

- Set the speed using and (LED 2 will flash)

To elect the reverse mode and invert the direction of stirring

at regular intervals, press the button . In the revers mode

the stirring direction will be inverted every 30 seconds; there

will be pause of 5 seconds between each changeover. The

LED 1 will flash when the revers mode is active.

The speed setting and revers mode selection will remain

unchanged when the instrument is unplugged.

Caution: At some speeds, irregularities in the shape of

the stirring bar and of the bottom of the container can cause

the bar to move irregularly during stirring. Increase or decre-

ase the speed until the stirring bar begins to rotate evenly.

The appliance is maintenance-free.

Cleaning

Only use cleansing agents which have been recommended

by IKA.

Use to remove:

Dyes Isopropyl alcohol

construction materials water containing tenside,

isopropyl alcohol

Cosmetics water containing tenside,

isopropyl alcohol

Foodstuffs water containing tenside

Fuels water containing tenside

- Do not allow moisture to get into the appliance when

cleaning.

- Wear protective gloves during cleaning the devices.

- Before using another than the recommended method for

cleaning or decontamination, the user must as certain

with IKA that this method does not destroy the instru-

ment.

IKA - stirring bars:

TRIKA

IKAFLON

Stirring bar remover

Starting up Maintenance

Accessories

In accordance with IKA warranty conditions, the warranty

period is 24 months. For claims under the warranty please

contact your local dealer. You may also send the machine

direct to our factory, enclosing the delivery invoice and giving

reasons for the claim. You will be liable for freight costs.

The warranty does not cover worn out parts, nor does it apply

to faults resulting from improper use, insufficient care or

maintenance not carried out in accordance with the instruc-

tions in this operating manual.

Plug-in power supply unit:

Rated voltage: VAC 100 - 240

Rated frequency: Hz 50 - 60

Output voltage: VDC 12

Absorbed power: W5

Output power: Wmin. 3

Magnetic stirrer: coil drive 4-pole

Speed range: rpm 15 - 1500

Stirred quantity (max.): ml

800 (at 1500 rpm with

25mm stirring bar)

Operating time: %100

Protection class: II

Pollution degree: 2

Overvoltage category: II

EN 60529 protection class: IP 65

Ambient humidity (relative) %80

Ambient temperature: °C

5 to 40 (in the operation)

Transport temperature: °C -25 to +70

Storage temperature: °C -10 to +70

Material: Housing PA GF

TPU

Front membrane sheet Polyester

Weight: kg 0,3

Installed weight (max.): kg 2,0

Set-up surface: mm ø 100

Dimensions: (W x D x H) mm 116 x 175 x 12

Warranty Technical data

Otros manuales para Lab disc

Tabla de contenidos

Otros manuales de Equipo de laboratorio de IKA

IKA

IKA STARVISC 200-2.5 control Manual de usuario

IKA

IKA IKATRON ETS-D6 Manual de usuario

IKA

IKA NANOSTAR 7.5 digital Manual de usuario

IKA

IKA Algaemaster 10 Manual de usuario

IKA

IKA MICROSTAR control Series Manual de usuario

IKA

IKA Color Squid Manual de usuario

IKA

IKA Dry Block Heater 1 Manual de usuario

IKA

IKA Mini MR standard Manual de usuario

IKA

IKA C 200 Manual de usuario

IKA

IKA HBR 4 control Manual de usuario

IKA

IKA C-MAG HS 10 Manual de usuario

IKA

IKA ICC control Manual de usuario

IKA

IKA LR 1000 basic Manual de usuario

IKA

IKA MATRIX Orbital Delta F0.5 Manual de usuario

IKA

IKA RET control Manual de usuario

IKA

IKA HABITAT Manual de usuario

IKA

IKA RW 16 basic Manual de usuario

IKA

IKA RET basic safety control Manual de usuario

IKA

IKA MS 3 digital Manual de usuario

IKA

IKA AOD 1 Manual de usuario

IKA

IKA KMO 3 basic Manual de usuario

IKA

IKA ULTRA-TURRAX T 18 basic Manual de usuario

IKA

IKA Vortex 3 Manual de usuario

IKA

IKA ULTRA-TURRAZ UTL 1000/10 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario

Yamato

Yamato BM510 Manual de usuario