Ignite B64800101 Manual

7495823enUS (A)

November 2022

Printed in USA

Original Instructions

Operation & Maintenance Manual

Three-Point Tine Rake

Three-Point Tine Rake 60 S/N: B64800101 & Above

Three-Point Tine Rake 72 S/N: B64900101 & Above

Three-Point Tine Rake 84 S/N: B64A00101 & Above

FOREWORD............................................................................................................................................................3

SERIAL NUMBER LOCATION ...........................................................................................................................3

IMPLEMENT IDENTIFICATION ..........................................................................................................................3

Front Of Implement ........................................................................................................................................3

Rear Of Implement.........................................................................................................................................3

FEATURES AND ACCESSORIES ......................................................................................................................4

Standard Items..............................................................................................................................................4

SAFETY AND TRAINING RESOURCES....................................................................................................................5

SAFETY INSTRUCTIONS..................................................................................................................................5

Safe Operation Is The Operator’s Responsibility (Implement) ..................................................................................5

Safe Operation Needs A Qualified Operator......................................................................................................... 5

Use Safety Rules ...........................................................................................................................................5

Call Before You Dig ........................................................................................................................................5

Silica Dust Exposure.......................................................................................................................................6

FIRE PREVENTION...........................................................................................................................................6

Maintenance.................................................................................................................................................6

Operation.....................................................................................................................................................6

Electrical......................................................................................................................................................6

Hydraulic System...........................................................................................................................................6

Fueling ........................................................................................................................................................7

Starting........................................................................................................................................................7

Spark Arrester Exhaust System......................................................................................................................... 7

Welding And Grinding .....................................................................................................................................7

Fire Extinguishers ..........................................................................................................................................7

PUBLICATIONS AND TRAINING RESOURCES .................................................................................................8

IMPLEMENT SIGNS (DECALS) .........................................................................................................................8

OPERATING INSTRUCTIONS ................................................................................................................................ 10

DAILY INSPECTION........................................................................................................................................ 10

Implement Mounting Frame............................................................................................................................ 10

Three-Point Hitch......................................................................................................................................... 10

OPERATING PROCEDURE WITH COMPACT TRACTORS ............................................................................... 11

Approved Compact Tractor Models & Requirements............................................................................................ 11

Compact Tractor / Implement Setup ................................................................................................................. 11

Entering And Exiting The Compact Tractor ........................................................................................................ 11

Installing The Three-Point Implement ............................................................................................................... 11

Control Functions Three-Point Hitch (Implement) ................................................................................................ 14

Driving The Implement And Tractor To Worksite.................................................................................................. 14

Angled Positioning ....................................................................................................................................... 15

Backfilling Positioning ................................................................................................................................... 16

Operating The Three-Point Implement .............................................................................................................. 16

Removing The Three-Point Implement.............................................................................................................. 16

LIFTING THE IMPLEMENT.............................................................................................................................. 19

TRANSPORTING THE IMPLEMENT ON A TRAILER ........................................................................................ 19

Fastening The Implement To A Trailer............................................................................................................... 19

TRANSPORTING THE IMPLEMENT AND MACHINE ON A TRAILER................................................................ 20

PREVENTIVE MAINTENANCE............................................................................................................................... 22

MAINTENANCE SAFETY WARNINGS ............................................................................................................. 22

TROUBLESHOOTING CHART ........................................................................................................................ 23

TABLE OF CONTENTS

MAINTENANCE INTERVALS........................................................................................................................... 24

LUBRICATION LOCATIONS............................................................................................................................ 24

REMOVING AND INSTALLING PIVOT MOUNT ................................................................................................ 25

REMOVING AND INSTALLING RAKE TINES ................................................................................................... 27

STORAGE AND RETURN TO SERVICE........................................................................................................... 28

Implement Storage....................................................................................................................................... 28

Return To Service ........................................................................................................................................ 28

SPECIFICATIONS.................................................................................................................................................. 29

TINE RAKE DIMENSIONS ............................................................................................................................... 29

PERFORMANCE SPECIFICATIONS ................................................................................................................ 31

TORQUE SPECIFICATION FOR BOLTS .......................................................................................................... 32

Torque For General SAE Bolts ........................................................................................................................ 32

Torque For General Metric Bolts...................................................................................................................... 33

WARRANTY .......................................................................................................................................................... 35

IMPLEMENT WARRANTY ............................................................................................................................... 35

TABLE OF CONTENTS

SERIAL NUMBER LOCATION

Figure 1

P142017b

Always use the serial number (Item 1) [Figure 1] of the

three-point tine rake when requesting service information

or when ordering parts. Earlier or later models

(identification made by serial number) may use different

parts, or it may be necessary to use a different procedure

in doing a specific service operation.

IMPLEMENT IDENTIFICATION

Front Of Implement

Figure 2

P-96311a

REF. DESCRIPTION

1 Locking Pin

2 Storage Stand

3 Rake Tine

4 Pivot Assembly

Rear Of Implement

Figure 3

P-96312a

FOREWORD

REF. DESCRIPTION

1 Three-Point Hitch (Category 1)

2 Mainframe

3 Tine Rake Frame

FEATURES AND ACCESSORIES

Standard Items

The three-point tine rake is equipped with the following

standard items

• Five Forward Angles.

• Five Rear Angles.

• Rear Three-Point Quick Hitch Compatible.

• Equipped With Storage Stand.

FOREWORD

SAFETY INSTRUCTIONS

Safe Operation Is The Operator’s

Responsibility (Implement)

Safety Alert Symbol

This symbol with a warning statement means:

“Warning, be alert! Your safety is involved!” Carefully

read the message that follows.

DANGER

The signal word DANGER on machine signs and in

the manuals indicates a hazardous situation which, if

not avoided, will result in serious injury or death.◂

D-1002

WARNING

The signal word WARNING on the machine and in the

manuals indicates a potentially hazardous situation

which, if not avoided, could result in serious injury or

death.◂

W-2044

IMPORTANT

This notice identifies procedures which must be

followed to avoid damage to the machine.◂

I-2019

The machine and implement must be in good operating

condition before use.

Check all of the items on the Service Schedule decal (if

equipped) in the Every 10 Hours section or as shown in

the Operation & Maintenance Manual.

Safe Operation Needs A Qualified Operator

For an operator to be qualified, he or she must not use

drugs or alcoholic drinks which impair alertness or

coordination while working. An operator who is taking

prescription drugs must get medical advice to determine

if he or she can safely operate a machine.

Use Safety Rules

• Read and follow instructions in the machine and the

implement’s Operation & Maintenance Manual

before operating.

• Check for underground lines before operating

implement (if applicable).

• In addition to the design and configuration of

equipment, hazard control, and accident prevention

are dependent upon the awareness, concern,

prudence, and proper training of personnel involved

in the operation, transport, maintenance, and

storage of equipment.

• Check that the implement is securely fastened to the

machine.

• Make sure all the machine controls are in the neutral

position before starting the machine.

• Operate the implement only from the operator’s

position.

• Operate the implement according to the Operation &

Maintenance Manual.

• When learning to operate the implement, do it at a

slow rate in an area clear of bystanders.

• DO NOT permit personnel to be in the work area

when operating the machine and implement.

• The implement must be used ONLY on approved

machines. Visit igniteattachments.com for an

updated list of approved implements for each

machine model.

• DO NOT modify equipment or add implements that

are not approved by the manufacturer.

• DO NOT make any adjustments or repairs on the

machine or implement while the engine is running.

• Keep shields and guards in place. Replace if

damaged.

Call Before You Dig

P200081

Dial 811 (USA Only)

Dial 1-888-258-0808 (USA & Canada)

When you call, you will be directed to a location in your

state / province / city for information about buried lines

(telephone, cable TV, water, sewer, gas, etc.).

SAFETY AND TRAINING RESOURCES

Silica Dust Exposure

NA3504

Silica dust can cause lung disease and is known to the

state of California to cause cancer.

Cutting or drilling concrete containing sand or rock

containing quartz may result in exposure to silica dust.

Do not exceed Permissible Exposure Limits (PEL) to

silica dust as determined by OSHA or other job site Rules

and Regulations. Use a respirator, water spray, or other

means to control dust.

FIRE PREVENTION

NA3505

Maintenance

The machine and some attachments have components

that are at high temperatures under normal operating

conditions. The primary source of high temperatures is

the engine and exhaust system. The electrical system, if

damaged or incorrectly maintained, can be a source of

arcs or sparks.

Flammable debris (leaves, straw, etc.) must be removed

regularly. If flammable debris is allowed to accumulate, it

can cause a fire hazard. Clean often to avoid this

accumulation. Flammable debris in the engine

compartment is a potential fire hazard.

The operator’s area, engine compartment, and engine

cooling system must be inspected every day and cleaned

if necessary to prevent fire hazards and overheating.

All fuels, most lubricants, and some coolants mixtures are

flammable. Flammable fluids that are leaking or spilled

onto hot surfaces or onto electrical components can

cause a fire.

Operation

Do not use the machine where exhaust, arcs, sparks, or

hot components can contact flammable material,

explosive dust, or gases.

Electrical

P200082

Check all electrical wiring and connections for damage.

Keep the battery terminals clean and tight. Repair or

replace any damaged part or wires that are loose or

frayed.

Battery gas can explode and cause serious injury. Use

the procedure in the Operation & Maintenance Manual for

connecting the battery and for jump starting. Do not jump

start or charge a frozen or damaged battery. Keep any

open flames or sparks away from batteries. Do not

smoke in battery charging area.

Hydraulic System

Check hydraulic tubes, hoses and fittings for damage and

leakage. Never use open flame or bare skin to check for

SAFETY AND TRAINING RESOURCES

leaks. Hydraulic tubes and hoses must be properly routed

and have adequate support and secure clamps. Tighten

or replace any parts that show leakage.

Always clean fluid spills. Do not use gasoline or diesel

fuel for cleaning parts. Use commercial nonflammable

solvents.

Fueling

P200084

Stop the engine and let it cool before adding fuel. No

smoking! Do not refuel a machine near open flames or

sparks. Fill the fuel tank outdoors.

Ultra Low Sulfur Diesel (ULSD) poses a greater static

ignition hazard than earlier diesel formulations with

higher sulfur content. Avoid death or serious injury from

fire or explosion. Consult with your fuel or fuel system

supplier to ensure the delivery system is in compliance

with fueling standards for proper grounding and bonding

practices.

Starting

Do not use ether or starting fluids on any engine that has

glow plugs or an air intake heater. These starting aids

can cause explosion and injure you or bystanders.

Use the procedure in the Operation & Maintenance

Manual for connecting the battery and for jump starting.

Spark Arrester Exhaust System

The spark arrester exhaust system is designed to control

the emission of hot particles from the engine and exhaust

system, but the muffler and the exhaust gases are still

hot.

Check the spark arrester exhaust system regularly to

make sure it is maintained and working properly. Use the

procedure in the Operation & Maintenance Manual for

cleaning the spark arrester muffler (if equipped).

Welding And Grinding

Always clean the machine and implement, disconnect the

battery, and disconnect the wiring from the Ignite

Attachments controllers before welding. Cover rubber

hoses, battery, and all other flammable parts. Keep a fire

extinguisher near the machine when welding.

Have good ventilation when grinding or welding painted

parts. Wear a dust mask when grinding painted parts.

Toxic dust or gas can be produced.

Dust generated from repairing nonmetallic parts such as

hoods, fenders, or covers can be flammable or explosive.

Repair such components in a well-ventilated area away

from open flames or sparks.

Fire Extinguishers

P200083

Know where fire extinguishers and first aid kits are

located and how to use them. Inspect the fire

extinguisher and service the fire extinguisher regularly.

Obey the recommendations on the instructions plate.

SAFETY AND TRAINING RESOURCES

PUBLICATIONS AND TRAINING

RESOURCES

The following publications are also available for your

Ignite Attachments implement. Access them online at

igniteattachments.com.

C217655

Operation & Maintenance

Manual

Complete instructions on

the correct operation and

the routine maintenance

of your implement.

7495823.

For the latest information on Ignite Attachments products

and the Ignite Attachments Company, visit our website at

igniteattachments.com.

IMPLEMENT SIGNS (DECALS)

Figure 4

P-96311b

REF. DECAL

1 Crush Warning

Located near 3 point hitch, both sides

71892000IG

2 Prop 65

Located near 3 point hitch

73536420IG

SAFETY AND TRAINING RESOURCES

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para tractores de Ignite

Ignite

Ignite Blade Box 48 Manual

Manuales populares de Accesorios para tractores de otras marcas

Land Pride

Land Pride SGC0548 Manual de usuario

Swisher

Swisher Versa Commercial Pro VSP50 Manual de usuario

matev

matev FPS-FKH-Kioti CX 2510 Manual de usuario

matev

matev SCA-130 Manual de usuario

Toro

Toro 08733 Manual de usuario

Avantco

Avantco A425119 Manual de usuario

FTS

FTS G-FTL Series Manual de usuario

Sami

Sami 150-50 Manual de usuario

CAMSO

CAMSO TTS 30 Series Manual de usuario

Luda

Luda tractorCam S Manual de usuario

HLA

HLA BALE KNIFE Series Manual de usuario

P.Lindberg

P.Lindberg 9059890 Instrucciones de operación

Ventrac

Ventrac KD482 Manual de usuario

Original Tractor Cabs

Original Tractor Cabs 4421381 Hoja de datos

Grouser Products

Grouser Products 760 Manual de usuario

Degelman

Degelman Landroller Manual de programación

Bush Hog

Bush Hog BS1 Series Manual de usuario

MX MX A104 Manual de usuario