IFM Electronic ID000A Manual de usuario

704727 / 00 07 / 2010

UK

Operating instructions

Inductive sensors

ID000A / ID500A

2

Operating instructions (safety-related part ATEX)

Remarks for safe use in hazardous areas

Functions and features

• Use in hazardous areas according to the classification

II 3D

(group II, category 3D, apparatus for dust atmosphere).

The requirements of the standards EN 61241-1 and EN 61241-0 are met.

Shock test to EN 60947-5-2 with 0.5 joules.

• Marking

II 3D Ex tD A22 IP65 T90°C X Ta: -20...60°C ID000A / ID500A

Installation / Set-up

The units must only be installed, connected and set up by qualified staff. The qualified staff

must have knowledge of protection classes, regulations and provisions for apparatus in

hazardous areas.

Check whether the classification (see "Marking" above and marking on the unit) is suitable

for the application.

Installation remarks / Installation

• Adhere to the relevant national regulations and provisions.

• The relevant installation regulations must be adhered to.

• Avoid electrostatic charging on housings and cables.

• To avoid electrostatic charging steps must be taken to ensure the equalisation of potential

of metal parts (plug housing, fixing elements, etc.).

• Protect the units and the cables efficiently against damage.

• To avoid soiling, do not remove the dust caps from the cable glands until introducing the

cables.

• For units with cable gland: To ensure the required minimum protection, the clamping screw

of the cable gland must be firmly tightened (see technical data sheet for tightening torque).

• Maintenance intervals are application-specific and therefore need to be defined by the

operator depending on the operating conditions.

• During maintenance, especially those parts on which the type of protection depends need

to be examined (e.g. integrity of the components of the cable gland, of the seals).

3

UK

Special conditions for safe operation

• For units with terminal chamber (cable gland) and cable units a sufficient strain relief must

be ensured or the cable must be firmly laid.

• For test purposes, the housing and housing parts made of plastic were exposed to

mechanical stress of 0.5 joules (in accordance with EN 60947-5-2). The user must take

appropriate measures (e.g. installation conditions, use of a protective device, etc.) to

ensure that the units are not exposed to major mechanical stress/shocks.

• Avoid direct radiation with high UV components (sunlight). Mount the unit in a protected

place.

• Units of the type ID must be mounted on a flat surface and the entire bottom must lie

flat on the surface. When mounted with the ifm mounting sets E11121 or E11122, these

requirements are met.

Maintenance / Repair

The unit must not be modified nor can it be repaired. In case of a fault please contact the

manufacturer.

Data sheets and EC declaration of conformity are available from the manufacturer on

request.

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Accesorios de IFM Electronic

IFM Electronic

IFM Electronic efector200 OC Manual de usuario

IFM Electronic

IFM Electronic O3M151 Manual del propietario

IFM Electronic

IFM Electronic efector 300 SM0505 Manual de usuario

IFM Electronic

IFM Electronic efector 200 O5D15 Series Manual de usuario

IFM Electronic

IFM Electronic efector 200 OJ51 Series Manual de usuario

IFM Electronic

IFM Electronic efector200 OT Series Manual de usuario

IFM Electronic

IFM Electronic TS502A Manual de usuario

IFM Electronic

IFM Electronic efector150 Manual de usuario

IFM Electronic

IFM Electronic efector 300 SI5004 Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

IFM Electronic

IFM Electronic Efector200 OG Manual de usuario

IFM Electronic

IFM Electronic SM7000 Manual de usuario

IFM Electronic

IFM Electronic efectro 200 Manual de usuario

IFM Electronic

IFM Electronic Efector500 PF2058 Manual de usuario

IFM Electronic

IFM Electronic OPD100 Manual de usuario

IFM Electronic

IFM Electronic efector500 PC3 Series Manual de usuario

IFM Electronic

IFM Electronic efector160 LR7000 Manual de usuario

IFM Electronic

IFM Electronic Efector 200 Manual de usuario

IFM Electronic

IFM Electronic PN2 Series Manual de usuario

IFM Electronic

IFM Electronic efector 160 Manual de usuario

IFM Electronic

IFM Electronic Efector 200 Manual de usuario

IFM Electronic

IFM Electronic efector300 SM8000 Manual de usuario

IFM Electronic

IFM Electronic O5H Manual de usuario

IFM Electronic

IFM Electronic Efector 100 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario