IDTECK Star SR10 Manual de usuario

IDTeck

SR10 / SR20

Philips Mifare™ Compatible Proximity Reader

Rev. V1.0

USER’S MANUAL

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

CONTENTS

1. Important Safety Instructions page 3

2. Product Introduction page 3

3. Features page 4

4. Identifying supplied parts page 4

5. Specification page 4

6. Installation page 5

7. Wire Colour Table of the Reader page 5

8. Output Format page 6

9. Wire Connection to Controller page 7

10. Operation page 7

11. FCC Registration Information page 8

12. Contacts page 9

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

1. Important Safety Instructions

When using NESS - IDTECK SR10/SR20 Philips Mifare™ Compatible Proximity Reader, basic safety precautions should

always be followed to reduce the risk of fire, electrical shock, and injury to persons. In addition, the following should also

be followed:

1. Read and understand all instructions of the User’s Manual.

2. Follow all warnings and instructions marked on the product.

3. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

If necessary, use mild soap.

4. Do not use this product near water, such as bath-tub, wash bowl,

kitchen sink, laundry tub, in a wet basement or swimming pool.

5. This product should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of power

supplied to your installation site, consult your dealer or local power

company.

6. Never push objects of any kind into this product or through the cabinet

slots as they may touch voltage points or short out parts that could

result in fire or electric shock. Never spill liquid of any kind on the

product.

7. To reduce the risk of electric shock, do not disassemble this product by

yourself. Take it to qualified service whenever service or repair is required.

8. Unplug this product from the Direct Current (DC) power source and

refer to qualified service personnel under these conditions:

zThe power supply cord or plug is damaged or frayed.

zLiquid has been spilled on the product.

zThe product does not operate normally after following the operating instructions in this manual.

zThe product exhibits a distinct change in performance.

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

2. Product Introduction

The NESS - IDTECK SR10/ SR20 Philips Mifare™ Compatible Proximity Reader is an elegant looking 10cm (4”) read

range Proximity Reader that can be mounted to any flat wall surface. The SR10 / SR20 Philips Mifare™ Compatible

Reader which reads serial numbers from Philips Mifare™ compatible cards and transmits the data to the control panel in

various output formats. The SR10/ SR20 uses an epoxy-potted electronics module that ensures you successful operation

even in harsh environments. The two-colour LED (green and red) and the Piezo buzzer inside the reader will guarantee you

accurate and reliable system operations.

3. Features

-Philips Mifare™ Compatible Proximity Reader.

-Maximum 10cm (4”) reading range.

-External LED and Buzzer control inputs.

-2-Colour LED (Red and Green) Indicator and Buzzer sound.

-Output format selectable between 34-bit / 26-bit Wiegand.

-Optional RS232 communication port.

-Operating voltage from 7V to 17VDC.

4. Identifying Supplied Parts

* Please unpack and check the contents of the box:

Reader Module SR10 Bezel or SR20 Bezel Instruction

(1ea) (1ea) (1ea) (1ea)

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

5. Specification

Read Range: Up to 10cm (4”).

Read Format: Philips Mifare™ Compatible Proximity Card Format.

Operating Frequency: 13.56 MHz.

Compatibility: ISO14443 type A.

Power: DC 7V ~ 17V, Max. 150mA.

Output Format: 34-bit or 26-bit Wiegand, Optional RS232 communication port.

External LED/Buzzer control Input: Low Active, DC 0 ~ 5V, Max. 50mA.

LED/ Buzzer: Two-colour LED (red and green) / Piezo Buzzer.

Colour: Dark Pearl Grey.

Operating Environment: -15˚~ +65˚C (5˚~ 149˚F), 10~90% RH.

OverallSize(WxHxD): SR10: 46x122x23mm (1.82”x4.81”x0.87”).

SR20: 76x124x23.5mm (3.00"x4.89"x0.87").

Weight (SR10 / SR20): 150g (0.33lb) / 160g (0.35lb).

6. Installation

6-1. Mullion/Wall Mount:

Drill two 6-32 or M3 holes 8.38cm (3.3") apart in vertical and drill one 1/2" hole for

the reader cable 4.31cm (1.7") apart from the top hole.

(Skip this step, if you have installed an electric gang box.)

6-2. Put reader cable into the centre hole and install the reader module using two 6-32 or M3 screws.

6-3. Put bezel into the reader module, then push bezel until you hear the locking sound.

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

7. Wire Colour Table of the SR10/20

POWER

Power (DC +7V ~ +17V) DC (+) Red wire

Power (Ground) GND Black wire

INPUT

LED Control LED_CON Yellow wire

Buzzer Control Buzzer_CON Blue wire

Output Format Selection 34 bit / 26 bit select 34/26_SLCT Grey wire

OUTPUT (Wiegand Format)

Wiegand Data-0 Data-0 Green wire

Wiegand Data-1 Data-1 White wire

OUTPUT (RS232 Format)

RS232C TX Violet wire

8. Output Format

8-1. Wiegand Output Format

Data format (34-bit /26-bit)

Bit1/Bit1: Even parity from Bit 2 to Bit 17/ Bit 2 to Bit 13

Bit 2 to Bit 33/ Bit 2 to Bit 25: 4-byte ID number/ 3-byte ID number

Bit 34/ Bit 26: Odd parity from Bit 18 to Bit 33/ Bit 14 to Bit 25

Timing diagram

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

8.2 RS-232C (Optional) Data format

STAR (0x02H) DATA (10 or 8 characters) END (0x03H) LRC

Baud rate : 9600

DATA : 10 characters for 4-byte output, 8 characters for 3-byte.

LRC : The value made from XORing every byte from ‘NESS - IDTECK’ through ‘END’

9. Wire Connection to Controller

The brown and the orange wire MUST be left unconnected. The violet wire is reserved for RS-232C output.

Please be careful connecting the wires not to make a misconnection.

10. Operation

10-1. Apply power and you can see the red LED is on, indicating the reader is on ‘Standby ’.

10-2. Present a proximity card to the reader until you hear a beep sound and the LED changes the colour to green

simultaneously and the reader sends the RF card data to the controller. Then the LED changes the colour to red again

for next reading.

10-3. LED Control:

To change the LED colours, you may connect the LED Control Input (Yellow wire) to the power ground. Then the

green LED is On.

Present a proximity card. The LED changes the colour to red simultaneously, then to green again for next reading.

10-4. Buzzer Control:

When the reader reads a proximity card, only one beep sound generates in normal operating mode but you can

generate more beep sounds to distinguish whether the access is granted or denied.

To generate more beeps, you may control the Buzzer Control Input (Blue wire) to the power ground, and then you

can turn the beeper on while you hold the Buzzer Control Input to the power ground.

10-5. 4-byte (34bit) / 3-byte (26bit) selection:

The reader outputs the serial number of a card, which is a 4-byte number. It is possible to make the reader send only

3 bytes with the most significant byte trimmed off. It is useful when there are controllers which deal with 3-byte data

only as most of existing controllers do.

For 3-byte outputs, connect the 34-bit / 26-bit selection input (Grey wire) to ground.

Caution: It is unavoidable that some card numbers are duplicated in 3-byte output.

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

11. FCC REGISTRATION INFORMATION

FCC REQUIREMENTS PART 15

Caution: Any changes or modifications in construction of this device, which are not expressly approved by the

manufacturer for compliance, could void the user's authority to operate the equipment.

NOTE: This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interface.

2. This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the

FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the radio or television on and off, the user is

encouraged to try to correct the interference with one or more of the following measures.

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on another circuit.

4. Consult the dealer or an experienced radio/TV technician for help.

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

12. Contacts

Ness Security Products Pty Ltd

ABN 28 069 984 372

Head Office – NSW:

4 / 167 Prospect Hwy

Seven Hills, NSW, 2147 – Australia

Ph +61 2 8825 9222

Fax + 61 2 9674 2520

www.ness.com.au

email:[email protected]

NSW:

4 / 167 Prospect Hwy

Seven Hills, NSW, 2147

Ph (02) 8825 9222

Fax (02) 9674 2520

[email protected]

Vic:

24 Terracotta Drive

Blackburn, Vic, 3130

Ph (03) 9875 6400

Fax (03) 9875 6422

[email protected]

QLD:

Unit 3A / 471 Lytton Road

Morningside, Qld, 4170

Ph (07) 3399 4910

Fax (07) 3217 9711

[email protected]

W.A:

Unit 1, 567 Newcastle Street

Perth, W.A., 6000

Ph (08) 9328 2511

Fax (08) 9227 7073

[email protected]

IDTeck

–

SR10 / 20 SMART CARD PROXIMITY READER

MEMO

Otros manuales para Star SR10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de tarjetas de IDTECK

IDTECK

IDTECK NEO RF245 Manual de usuario

IDTECK

IDTECK LX006 Manual de usuario

IDTECK

IDTECK RF900I-8 Manual de usuario

IDTECK

IDTECK STAR RF70 Manual de usuario

IDTECK

IDTECK SR10S Manual de usuario

IDTECK

IDTECK Star SR10 Manual de usuario

IDTECK

IDTECK Star SR10 Manual de usuario

IDTECK

IDTECK SR10RW Manual de usuario

IDTECK

IDTECK Star RF TINY Manual de usuario

IDTECK

IDTECK Star RF10 Manual de usuario

IDTECK

IDTECK Star RF30 Manual de usuario

IDTECK

IDTECK Star FINGER006 Manual de usuario

IDTECK

IDTECK SRK101 Manual de usuario

IDTECK

IDTECK SR10/30V Manual de usuario

IDTECK

IDTECK Star RFK505 Manual de usuario

IDTECK

IDTECK Star RFK101 Manual de usuario

IDTECK

IDTECK PROX10 Manual de usuario

IDTECK

IDTECK PROX10 Manual de usuario

IDTECK

IDTECK Star RFK101 Manual de usuario

IDTECK

IDTECK Star RFK505 Manual de usuario

IDTECK

IDTECK Star RFK101 Manual de usuario

IDTECK

IDTECK SR30 Manual de usuario

IDTECK

IDTECK NEO RF245 Manual de usuario

IDTECK

IDTECK SR30 Manual de usuario

Manuales populares de Lector de tarjetas de otras marcas

Lindy

Lindy 43185 Manual de usuario

Lindy

Lindy 43185 Manual de usuario

ViziT

ViziT RD-4F Manual de usuario

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manual de usuario

AVID ID

AVID ID AVID1043 Manual de usuario

Conrad

Conrad PCMCIA Manual de usuario

Rosslare

Rosslare DR-6255 Manual de usuario

Lindy

Lindy 51541 Manual de usuario

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manual de usuario

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manual de usuario

ACS

ACS ACR122L Manual de usuario

Secukey

Secukey S2-MF Manual de usuario

Elecom

Elecom MR-SMC07 series Manual de usuario

Alien

Alien ALR-9800 Manual de usuario

ACS

ACS ACR310 Manual de usuario

Datamars

Datamars R-IN1300 MID Manual de usuario

Alarm Lock

Alarm Lock AL-PRE2 Manual de usuario

xpr

xpr B100PROX-AH Guía del usuario