IDEC LONWORKS Manual de usuario
LONWORKS® Communication Module User’s Manual i
Indicates that death or severe
bodily injury may occur, if the
corresponding safety measures
are not taken.
Safety Notices
DANGER
WARNING
CAUTION
CAUTION
WARNING
Indicates that death, severe bodily
injury or substantial material damage
will occur, if the corresponding safety
measures are not taken.
With the warning triangle, this
indicates that minor bodily
injury may occur, if the
corresponding safety measures
are not taken.
Without the warning triangle,
this indicates that material
damage may occur, if the
corresponding safety measures
are not taken.
This indicates that an undesirable
result or condition may occur, if the
corresponding instructions are not
observed.
LONWORKS® Communication Module User’s Manual ii
Copyright © IDEC IZUMI CORPORATION All rights reserved
You may not transfer or duplicate this document or utilize or reveal its contents,
unless expressly authorized in writing. In the case of a violation, you will be obliged
to pay damages. All rights reserved, in particular in the event that a patent is
granted or that a utility model is registered.
Disclaimer of liability:
We have checked that the contents of this document correctly describe the
associated hardware and software. Nonetheless, it is impossible to exclude the
possibility of deviations and therefore we cannot guarantee that there are no errors
in this document. The information in this document is checked regularly and any
necessary corrections are then made in the next release issued. We are of course
thankful for any suggestions for improvements.
LONWORKS® Communication Module User’s Manual iii
Table of Contents
1. Getting to know LONWORKS® Communication Module..... 1-1
1.1 What is LONWORKS® Communication Module ? ................... 1-1
1.2 The construction of the LONWORKS® Communication Module1-2
2. Mounting and wiring the LONWORKS® Communication Module…2-1
2.1 General guidelines .................................................................... 2-1
2.2 Wiring the LONWORKS® Communication Module .................. 2-3
2.2.1 Connecting the power supply...................................................2-4
2.2.2 Connecting the LON.................................................................2-5
3. Putting the LONWORKS® Communication Module into operation 3-1
3.1 Step-by-step.............................................................................. 3-1
3.2 The LONWORKS® Communication Module - operational status3-2
3.3 Behavior in case of a fault......................................................... 3-3
4. Supported functions.................................................................... 4-1
4.1 Virtual inputs / outputs............................................................... 4-1
4.2 Available network variables....................................................... 4-3
4.3 LON configuration parameters .................................................. 4-5
4.4 Inputs / Outputs – special considerations.................................. 4-6
4.5 Alias table entries...................................................................... 4-6
5. LONWORKS® Communication Module - Specifications ....... 5-1
LONWORKS® Communication Module User’s Manual 1-1
1. Getting to know
LONWORKS® Communication Module
1.1 What is LONWORKS® Communication
Module ?
The Local Operating Network (LONWORKS® Communication
Module) communications module is an interface for
connecting IDEC SmartRelay onto a LON network.
The IDEC SmartRelay communications module has been
implemented as a Slave module for the IDEC SmartRelay
control module.
The module supports communication between the IDEC
SmartRelay Master and external LON devices via a LON.
The LONWORKS® Communication Module is a bus station on
the LON and allows the IDEC SmartRelay to communicate
with other LON devices.
What are the capabilities of the LONWORKS®
Communication Module ?
The LONWORKS® Communication Module presents the
current states of the LON stations to the IDEC SmartRelay,
which is thus able to use its logical functions and timers to
join them together. In the process, the LON signals can also
be combined with the signals of the local IDEC SmartRelay
inputs and outputs. The LONWORKS® Communication
Module then transmits every change of the output signal via
the LON.
The combination of IDEC SmartRelay and LONWORKS®
Communication Module gives the user a decentralized
controller functionality for the LON with the capability of
setting or changing parameters or operations quickly, simply
and without a programming device.
LONWORKS® Communication Module User’s Manual 1-2
1.2 The construction of the LONWORKS®
Communication Module
LONWORKS® Communication Module User’s Manual 1-3
1. Power supply
2. Bus lock slider, interface to the IDEC SmartRelay
3. The RUN/STOP LED for IDEC SmartRelay
communication
4. The SERVICE LED
5. Input - LON connection
6. Expansion interface to the IDEC SmartRelay
7. Mechanical coding - pin
8. Service button
7
8
1
3
4
5
6
2
LONWORKS® Communication Module User’s Manual 2-1
2. Mounting and wiring the LONWORKS®
Communication Module
2.1 General guidelines
The following guidelines should be observed when mounting
wiring your LONWORKS® Communication Module:
- When wiring the LONWORKS® Communication Module,
make certain that you follow all of the applicable and
legally binding standards. Observe all of the relevant
national and regional regulations when installing and
operating the device. Check with the local authorities
regarding the standards and regulations that must be
observed in your special case.
- Make certain that the device is de-energized.
- Use only approved bus cables.
- Make certain that the specified cable lengths are used and
that the correct terminating resistors are installed properly.
- The LONWORKS® Communication Module must always
be installed as the last module on the right of the IDEC
SmartRelay, since you may not install other expansion
modules onto the LONWORKS® Communication Module.
LONWORKS® Communication Module User’s Manual 2-2
Please notice:
- The LONWORKS® Communication Module must have its
own power supply (24 V AC/DC).
NOTE
This module may only be mounted and wired by qualified
personnel, who know and observe the generally applicable
guidelines and applicable regulations and standards.
Observe the assembly and disassembly instructions in the
IDEC SmartRelay manual.
WARNING
The expansion module may only inserted or removed when
the power is off.
LONWORKS® Communication Module User’s Manual 2-3
2.2 Wiring the LONWORKS® Communication
Module
To wire the LONWORKS® Communication Module, use a
screwdriver with 3 mm wide blade.
- You do not need to use wire end ferrules when clamping
the wires.
NOTE
After the installation, the terminals must be covered. To
protect personnel against unintentional contact with the
portions of the LONWORKS® Communication Module that
are conducting electricity, the appropriate national and local
standards must be observed.
The LONWORKS® Communication Module is a double-
insulated switching device.
A protective grounding conductor is not necessary.
Tabla de contenidos
Otros manuales de Unidad de control de IDEC
IDEC
IDEC MICROSmart FC4A-SX5ES1E Manual de usuario
IDEC
IDEC FC5A-F2M2 Manual de usuario
IDEC
IDEC SmartRelay FL1D Series Manual de usuario
IDEC
IDEC HR1S-ATE Manual de usuario
IDEC
IDEC SmartRelay Series Manual de usuario
IDEC
IDEC HR6S Series Manual de usuario
IDEC
IDEC MICROSmart FC6A-C16K1CE Manual de uso y cuidado
IDEC
IDEC MicroSmart Series Manual de usuario
IDEC
IDEC HR6S-DN Manual de usuario
IDEC
IDEC MicroSmart pentra FC5A-C10R2 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
