ICPDAS PEX-P32C32 Series Manual de usuario

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

The package includes the following items:

One PEX-P32C32 or PISO-P32C32U (-5V) PCI Board.

One Software Utility CD (V5.2 or later)

One Quick Start Guide (This Document)

One CA-4037B Cable

Two CA-4002 D-Sub connectors

Step 1: Setup the Windows driver. The driver is located at:

The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it

is recommended to install this driver for new user:

CD: \NAPDOS\PCI\UniDAQ\DLL\Driver

http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/

The PISO-DIO Series classic driver supports Windows 98/NT/2K and 32-bit

XP/ 2003/ Vista/7/8. Recommended to install this driver for have been

used PISO-DIO series boards of regular user, please refer to :

http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/quickstar

t/classic/

For PEX-P32C32

PISO-P32C32U Series

What’s in the shipping package?

Installing Windows Driver

English/ Oct. 2013/ Version 1.3

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

Step 2: Click the “Next>”button to start the installation.

Step 3: Check your DAQ Card is or not on supported list, then click the

“Next>”button.

Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,

confirm and click the “Next>”button.

Step 5: Check your DAQ Card on list, then click the “Next>”button.

Step 6: Click the “Next>”button on the Select Additional Tasks window.

Step 7: Click the “Next>”button on the Download Information window.

Step 8: Select “No, I will restart my computer later”and then click the

“Finish”button.

For detailed information about the driver installation, please refer to Chapter

2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK

user manual.

Please make sure JP1 and JP2 jumper is kept in default setting before self-test,

as follows: ( This example uses this power supply.)

Jumper

JP1/JP2

Internal Power



External Power

(Default Setting)

Jumper Setting

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

Step 1: Shut down and power off your computer.

Step 2: Remove the cover from the computer.

Step 3: Select an unused PCI/PCI Express slot.

Step 4: Carefully insert your I/O card into the PCI/PCI Express slot.

Step 5: Replace the PC cover.

Step 6: Power on the computer.

After powering-on the computer, please finish the Plug&Play steps according

to the prompted messages.

R=10K O.C.

Out => BSP75N External

Device

External

Power

(+)

(-) GND

Low Drive

Channel

10V~30V

Open Collector Output Type & Notice

High Drive channel : Open collector N-channel Power FET (BPS75N) . Max. Sink

Current Is 500mA for Each Cannel .

Low Drive channel : Open collector NPN/PNO Transistor . Max. Sink Current Is

100mA for Each Channel .

(Recommend : It Is necessary to connect a diode In the External Device end as means

of preventing damage form the counter emf . If your External Device Is

inductive Load , Ex. Relay …)

R=3.9K External

Device

External

Power

(+)

(-) GND

High Drive

Channel

10V~30V

R=10K

O.C.

Out => 2N2222

Sink current

500mA

Sink current

100mA

Diode

External Power (+)

External Power (-)

DOn

Diode

PISO-P32S32WU

PISO- C64

P32C32

P32S32WU

External

Device

External

Power

(+)

(-) GND

PISO-P32A32 / PISO-A64

10V~30V

R=6.8K

O.C.

Out

R=10K

External Power (+)

DOn

Source current

100mA

External Power (-)

Low Drive

Channel

If your control device is an inductive load (ex: inductive relay), it is recommended

to connect a diode at the Control Device side as a means of preventing damage

from the counter EMF.

Wiring Note

Installing Hardware on PC

To prevent the board damaged forever by overload, the GND pins (CON1: pin 1/20,

CON2: pin 1/20) all must be connected with GND of External Power.

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

Pin Assignments

Extension Cable (CA-4037B):

DB-40-Pin conversion DB-37-Pin

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

Prepare for device:

DN-37 (optional) wiring terminal board.

Exterior power supply device. For example: DP-665 (optional)

Self-test wiring as follows:

1. Use the DN-37 to connect the CON1 on board.

2. Keep set the J1 and JP2 jumper to External Power (Page 2).

3. Connect the DI(0-15) with DO(0-15). (DI0 with DO0 …DI15 with DO15)

PEX-P32C32 and PISO-P32C32U External Power Wiring:

4. Power Supply (+24 V) connect to ECOM0 (Pin18).

Power Supply (+24 V) connect to Ext.PWR0 (Pin37).

Power Supply GND connect to IGND0 (Pin19).

Power Supply GND connect to Ext.GND0 (Pin1 and Pin20).

PISO-P32C32U-5V External Power Wiring:

4. Power Supply (+5 V) connect to ECOM0 (Pin18).

Power Supply (+5 V) connect to Ext.PWR0 (Pin37).

Power Supply GND connect to IGND0 (Pin19).

Power Supply GND connect to Ext.GND0 (Pin1 and Pin20).

Self-Test

The PEX-P32C32/PISO-P32C32U suggests input voltage range as follow:

Logic high: +9 ~ +24 V; Logic Low: 0 ~ 1V.

(Higher voltage over the limitation will cause the hardware damage.)

The PISO-P32C32U-5V suggests input voltage range as follow:

Logic high: +5 ~ +12 V; Logic Low: 0 ~ 1V.

(Higher voltage over the limitation will cause the hardware damage.)

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

The PEX-P32C32/PISO-P32C32U wiring is illustrated in the figure below:

The PISO-P32C32U-5V wiring is illustrated in the figure below:

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

5. Execute the UniDAQ Utility Program.

This program (UniDAQ Utility) will be

placed in the default path after

completing installation.

The UniDAQ Utility.exe is located in:

C:\ICPDAS\UniDAQ\Driver\

(Default path).

6. Get DIO function test result.

Confirm the PISO-P32C32U

series card had successfully

installed to PC. It starts from 0.

Double-Click

Click this button

to start test.

Select the “Port 0”.

Check channel 0, 2, 4, 6

Click “Digital Output” item.

Port0: DO0-7

Port1: DO8-15

Port2: N.C.

Port3: N.C.

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.

WebSite: http:// www.icpdas.com.tw E-Mail: service@icpdas.com , service.icpdas@gmail.com

Note!! All the DI should become red because all the DO is OFF (uncheck).

PEX-P32C32 and PISO-P32C32U Series Card Product Page:

http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-p32c32u.html

DN-37, CA-3710 and DP-665 page (optional):

http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm

http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm

http://www.icpdas.com/products/Accessories/cable/cable_selection.htm

Documentation and Software:

CD:\NAPDOS\PCI\UniDAQ\

http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/

Select the “Port 0”

The corresponding D/I becomes black

for channel 0, 2, 4, 6 of D/O is ON.

Click “Digital Input”item.

Related Information

Port0: DI0-7

Port1: DI8-15

Port2: N.C.

Port3: N.C.

PASS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de E/S de ICPDAS

ICPDAS

ICPDAS I-8093W Manual de usuario

ICPDAS

ICPDAS USB-87P2 Manual de usuario

ICPDAS

ICPDAS ET-2242U Manual de usuario

ICPDAS

ICPDAS DIO-48 Manual de usuario

ICPDAS

ICPDAS ET-2261 Manual de usuario

ICPDAS

ICPDAS WinCon-8000 Manual de usuario

ICPDAS

ICPDAS ET-7000 Manual de usuario

ICPDAS

ICPDAS CAN-2053C Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario