ICP DAS USA I-7067 Manual de usuario
I-7067 - 7 Channel Relay Output DAQ Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
I-7067
7 Channel Relay Output Data Acquisition
Module with Form A Relay Outputs
Quick Start Guide
Product Website:
http://www.icpdas-usa.com/i_7067_i_7067d.html
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
I-7067 is a 7-channel Relay Output Data Acquisition Module for signal conditioning
system monitoring. Providing safe value settings, I-7067 is a cost-effective solution for a
wide range of industrial control signals and systems. The DCON utility can help users to
configure and test I-7067 Relay Output module. The various library functions and demo
programs it provides makes it easy for users to develop programs in Windows, Linux
and DOS operating systems. I-7067 communicates over Modbus protocol via RS-485.
Users can mount the module on a DIN rail, panel or wall. Modules have a screw-
terminal block to connect to the signals. The I-7067 relay output data acquisition module
can be used in various applications such as industrial automation and control, factory
automation, remote monitoring, etc.
2. Terminal Assignment
I-7067 - 7 Channel Relay Output DAQ Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram
4. Default Settings
。Module Address: 01
。DIO Type: Type 40
。Baud Rate: 9600 bps
。Checksum disabled
。J3 set to INIT mode enabled
I-7067 - 7 Channel Relay Output DAQ Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
5. Configuration
To install the module, follow the steps below:
1. Connect the relay output.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.
I-7067 - 7 Channel Relay Output DAQ Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.
I-7067 - 7 Channel Relay Output DAQ Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC
I-7067 - 7 Channel Relay Output DAQ Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
7. For I-7000 modules, DCON utility pro terminal can send command to the module.
See user manual Sections 2 for details command.
Configure the module: sending the %AANNTTCCFF command. See user manual
Section 2 for details.
Read data from the input channels: send either the #AA or #AAN command to the
module.
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Registrador de datos de ICP DAS USA
ICP DAS USA
ICP DAS USA CL-201-WF Manual de usuario
ICP DAS USA
ICP DAS USA DL-110S-E Manual de usuario
ICP DAS USA
ICP DAS USA ET-7053 Manual de usuario
ICP DAS USA
ICP DAS USA ET-7044 Manual de usuario
ICP DAS USA
ICP DAS USA DL-100S-E Manual de usuario
ICP DAS USA
ICP DAS USA DL-300-WF Series Manual de usuario
ICP DAS USA
ICP DAS USA CAN-Logger Series Manual de usuario
ICP DAS USA
ICP DAS USA PET-AR400 Manual de usuario
ICP DAS USA
ICP DAS USA M-7026 Manual de usuario
ICP DAS USA
ICP DAS USA ET-7002 Manual de usuario
