Icom IC-G86 Guía de configuración

10 TROUBLESHOOTING

9 PROGRAMMING

8 SET MODES

7 DTMF MEMORY

TONE SQUELCH AND POCKET BEEP

5 SCAN OPERATION

REPEATER OPERATION

3 ADVANCED OPERATION

2 BATTERY CHARGE

1 ACCESSORIES

INTRODUCTION

ADVANCED MANUAL

VHF TRANSCEIVER

|G86

11 OPTIONS

INTRODUCTION

Thank you for choosing this Icom product. This

product was designed and built with Icom’ s state of

the art technology and craftsmanship. With proper

care, this product should provide you with years of

trouble-free operation.

IMPORTANT

READ ALL INSTRUCTIONS carefully and completely

before using the transceiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains advanced operating

instructions for the IC-G86. For basic operating

instructions, see the BASIC MANUAL.

FEATURES

zRugged construction (IP54*1and MIL-STD-810G)

LOnly when the battery pack or case, antenna, and

jack cover or optional HM-168LWP, HS-94LWP,

HS-95LWP are attached.

zPowerful 7 W of output power (Extra High power)

zExtend Battery Life function (With the BC-240)

Icom, Icom Inc. and the Icom logo are registered

trademarks of Icom Incorporated (Japan) in Japan,

the United States, the United Kingdom, Germany,

France, Spain, Russia, Australia, New Zealand, and/or

other countries.

All other products or brands are registered trademarks

or trademarks of their respective holders.

Icom is not responsible for the destruction, damage

to, or performance of any Icom or non-Icom

equipment, if the malfunction is because of:

• Force majeure, including, but not limited to, res,

earthquakes, storms, oods, lightning, other

natural disasters, disturbances, riots, war, or

radioactive contamination.

• The use of Icom transceivers with any equipment

that is not manufactured or approved by Icom.

EXPLICIT DEFINITIONS

WORD DEFINITION

RWARNING! Personal injury, re hazard or

electric shock may occur.

CAUTION Equipment damage may occur.

NOTE

If disregarded, inconvenience only.

No risk of personal injury, re or

electric shock.

1-1

Section 1ACCESSORIES

Supplied accessories..............................................................................1-2

Antenna ..................................................................................................1-2

Belt clip...................................................................................................1-2

Battery pack or case...............................................................................1-3

Jack cover ..............................................................................................1-3

1ACCESSORIES

1-2

Supplied accessories

Battery pack

Jack cover

(with screws)

Battery charger

Belt clip

Power adapter

Antenna

NOTE: Some accessories are not supplied, or the

shape is different, depending on the transceiver

version.

Antenna

Insert the antenna into the antenna connector and

rotate the antenna base to lock it in place.

CAUTION:

• DO NOT carry the transceiver by holding only the

antenna.

• DO NOT transmit without an antenna.

Belt clip

To attach the belt clip:

zSlide the belt clip in the direction of the arrow until

the belt clip locks in place, and makes a ‘click’

sound.

Belt clip

Battery pack/case

To detach the belt clip:

1. Remove the battery pack or case from the

transceiver, if it is attached.

2. Lift the tab up (1), and slide the belt clip in the

direction of the arrow (2).



1ACCESSORIES

1-3

Battery pack

To attach:

1. Insert the battery pack in the direction of the

arrow (1), then close.

2. Hook the latch until it makes a ‘click’ sound (2).



Battery pack

Latch

To detach:

RWARNING! The latch is tightly locked, so use

caution when releasing it. DO NOT use your

ngernail. Use the edge of a coin or screwdriver tip

to carefully release it.

zUnhook the latch (1), and then lift up the battery

pack in the direction of the arrow (2).





CAUTION: NEVER detach or attach the battery pack

when the transceiver is wet or soiled. This may result

in water or dust getting into the transceiver or the

battery pack, and may result in them being damaged.

NOTE: Keep battery terminals clean. It’s a good idea

to occasionally clean them.

Jack cover

Attach the jack cover when optional equipment is not

used.

To attach the jack cover

1. Attach the jack cover to the [SP MIC] jack (1).

2. Insert and tighten the screws (2).

To detach the jack cover

1. Remove the screws with a phillips screwdriver (1).

2. Detach the jack cover to connect optional

equipment (2).





2-1

Section

Battery chargers .....................................................................................2-2

DUsing the BC-191 to rapid charge the BP-264 ...............................2-2

DUsing the BC-192 to regular charge the BP-264 ............................2-2

DUsing the BC-240 to rapid charge the BP-298/BP-299 ..................2-3

2BATTERY CHARGE

2-2

The BC-191 provides rapid charging of only the

BP-264 Ni-MH battery pack. Never use it to charge

any other battery pack.

Charging time: Approximately 2 hours

Additionally needed item (purchase separately):

A power adapter (not supplied with some transceiver

versions) or the OPC-515L or CP-23L DC power cable.

LA power adapter may a different type, or no power

adapter is supplied, depending on the transceiver

version.

LThe optional OPC-515L (for a DC power source) or

CP-23L (for a 12 V cigarette lighter socket) can be

used instead of the power adapter.

NOTE: When the BC-191’s charging indicator lights

as below, it indicates the following states.

• Lights orange: While charging

• Lights green: When charging is completed.

The BC-192 provides regular charging of only the

BP-264 Ni-MH battery pack. Never use it to charge

any other battery pack.

Charging time:

At 12 V: Approximately 36 hours

At 13.8 V: Approximately 21 hours

At 16 V: Approximately 16 hours

LCharging time period differs, depending on the

input voltage.

Additionally needed item (purchase separately):

A power adapter (not supplied with some transceiver

versions) or the OPC-515L DC power cable.

LA power adapter may a different type, or no power

adapter is supplied, depending on the transceiver

version.

LThe optional OPC-515L (for a DC power source)

can be used instead of the power adapter.

NOTE: When the BC-192’s charging indicator lights

as below, it indicates the following state.

• Lights green: While charging.

LThe charge indicator will not go out even after a

battery pack is fully charged.

The optional OPC-515L

(for a DC power source)

or CP-23L (for a 12 V

cigarette lighter socket)

Power adapter

Battery pack + Transceiver

Turn OFF

Battery pack

The optional OPC-515L

(for a DC power source)

Power adapter

Battery pack + TransceiverBattery pack

Turn OFF

Battery chargers

DUsing the BC-191 to rapid charge the BP-264

DUsing the BC-192 to regular charge the BP-264

Screws

(Self tapping screw:

M3.5 × at least 30 mm)

LScrews are user

supplied.

LUsing screws are

recommended to

secure the charger.

Screws

(Self tapping screw:

M3.5 × at least 30 mm)

LScrews are user

supplied.

LUsing screws are

recommended to

secure the charger.

2BATTERY CHARGE

2-3

The BC-240 provides rapid charging of only the

BP-298/BC-299 Li-ion battery pack. Never use it to

charge any other battery pack.

Charging time*

With the BP-298: Approximately 3 hours

With the BP-299: Approximately 4.6 hours

* When the Extend Battery Life function is turned OFF.

See the BASIC MANUAL for details.

Additionally needed item (purchase separately):

A power adapter (not supplied with some transceiver

versions) or the OPC-515L or CP-23L DC power cable

LA power adapter may a different type, or no power

adapter is supplied, depending on the transceiver

version.

LThe optional OPC-515L (for a DC power source) or

CP-23L (for a 12 V cigarette lighter socket) can be

used instead of the power adapter.

CAUTION: When using the OPC-515L DC power

cable NEVER connect the OPC-515L to a power

source using reverse polarity. This will ruin the

battery charger. White line:

Black line:

–

NOTE: When the BC-240’s charging indicator lights

or blinks as below, it indicates the following states.

• Lights orange: While charging

• Lights green: When charging is completed.

• Blinks red:

When a charging error has occurred.

Reinstall the battery or the

transceiver.

The optional OPC-515L

(for a DC power source)

or CP-23L (for a 12 V

cigarette lighter socket)

Power adapter

Battery pack + TransceiverBattery pack

Turn OFF

Screws

(Self tapping screw:

M3.5 × at least 30 mm)

LScrews are user

supplied.

LUsing screws are

recommended to

secure the charger.

Battery chargers

DUsing the BC-240 to rapid charge the BP-298/BP-299

3-1

Section

Adjusting the audio level.........................................................................3-2

Selecting passband width.......................................................................3-2

[VOL] function assignment .....................................................................3-2

3ADVANCED OPERATION

3-2

Adjusting the audio level

zRotate [VOL]* to adjust the audio level.

• The display shows the audio level while adjusting.

LIf the squelch is closed, hold down [MONI] while

adjusting the audio level.

[DIAL]

[VOL]

* Use [VOL] or [Y]/[Z], depending on the setting of the “Dial

assignment” in the Initial Set mode. (p. 8-6)

Selecting passband width

Set both the transmission and reception passband

width to wide or narrow.

1. Push [FUNC], and then push [SET] to enter the

Set mode.

2. Push [Y] or [Z] to select the passband width item

(W/n).

3. Rotate [VOL] to select the passband width.

• “W”: Wide (FM mode)

• “n”: Narrow (FM-N mode)

4. Push [# ENT] to exit the Set mode.

The “Passband width” item in the Set mode

(FM mode is selected) (FM-N mode is selected)

[VOL] function assignment

[VOL] can be used as a channel selector instead of

[Y] and [Z], to suit your preference. However, when

[VOL] functions as a channel selector, [Y] and [Z]

function as volume controls.

Hold down [ ] for 1 second to turn OFF the power.

While holding down [Y] and [Z], turn ON the power

to enter the Initial Set mode.

3. Push [Y] or [Z] to select the dial assignment item

(tOP).

4. Rotate [VOL] to select an option.

5. Push [# ENT] to exit the Initial Set mode.

[VOL] and [Y]/[Z] function as described below,

depending on the option.

Option [VOL] [Y]/[Z]

tOP.VO Volume control Channel selector

tOP.di Channel selector Volume controls

The “Dial assignment” item in the Set mode

[VOL] functions as the volume control.

[VOL] functions as the channel selector.

Tabla de contenidos

Otros manuales de Transceptor de Icom

Icom

Icom IC-F1000 series Manual de usuario

Icom

Icom IC-820H Manual de usuario

Icom

Icom D-STAR ID-4100A Guía de instalación

Icom

Icom IC-910H Manual de usuario

Icom

Icom IC-M605E Manual de usuario

Icom

Icom IC-211 Manual de usuario

Icom

Icom A25C SPORT 66 USA Manual de lista de piezas

Icom

Icom IC-375A Manual de usuario

Icom

Icom ID-31E PLUS Guía de instalación

Icom

Icom IC-F6061 Manual de usuario

Icom

Icom IC-U8 Manual de usuario

Icom

Icom IC-F3023T/S Manual de usuario

Icom

Icom IC-V210T Manual de usuario

Icom

Icom IC-4SA Manual de usuario

Icom

Icom IC-V85 Manual de usuario

Icom

Icom IC-F6121D Manual de usuario

Icom

Icom IC-3220A Manual de usuario

Icom

Icom IC-F4GT Instrucciones de construcción

Icom

Icom ID-51A Guía de instalación

Icom

Icom IC-V8000 Manual de usuario

Icom

Icom IC-SAT100 Manual de usuario

Icom

Icom IC-F4029SDR Manual de usuario

Icom

Icom IC-746 Manual de usuario

Icom

Icom iC-F5012 Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario