Icom IC-4088S Manual de usuario

INSTRUCTION MANUAL

UHF C.R.S. TRANSCEIVER

i4088S

IC-4088S.qxd 03.10.2 8:20 Page A (1,1)

FOREWORD

Thank you for purchasing the IC-4088S

UHF C.R.S. (Citizen Radio

Service) FM transceiver. This C.R.S. FM transceiver is designed for

those who require top quality, performance and outstanding relia-

bility under the most demanding conditions.

IMPORTANT

READ ALL INSTRUCTIONS carefully and completely before using

the transceiver.

SAVE THIS INSTRUCTION MANUAL— This instruction manual

contains important operating instructions for the transceiver.

PRECAUTION

RWARNING! NEVER hold the transceiver so that the antenna

is very close to, or touching exposed parts of the body, especially

the face or eyes, while transmitting. The transceiver will perform

best if the microphone is 5 to 10 cm away and the transceiver is

vertical.

RWARNING! NEVER operate the transceiver with a headset

or other audio accessories at high volume levels.

NEVER attempt to charge alkaline cell batteries. Be aware that

external DC power connections will charge batteries inside the bat-

tery case. This will damage not only the battery case but also the

transceiver.

DO NOT operate the transceiver near unshielded electrical blast-

ing caps or in an explosive atmosphere.

DO NOT push the PTT when not actually desiring to transmit.

IC-4088S.qxd 03.10.2 8:20 Page i (1,1)

Place the unit in a secure place to avoid inadvertent use by children.

AVOID using or placing the transceiver in direct sunlight or in

areas with temperatures below 0°C or above +55°C.

The use of non-Icom battery packs may impair transceiver perfor-

mance and invalidate the warranty.

Even when the transceiver power is OFF, a slight current still ﬂows

in the radio. Remove the alkaline cells or battery pack from the

transceiver when not using it for a long time. Otherwise, the in-

stalled batteries will become exhausted.

DO NOT modify the transceiver for any reason.

KEEP the transceiver from the heavy rain, and NEVER immerse

it in the water. The transceiver construction is weather resis-

tant, (meets JIS grade 4) not waterproof.

When the low battery indicator blinks, the performance of the trans-

ceiver cannot be guaranteed.

DO NOT transmit for more than 3 sec., when operating with the

group mode and/or call ring function. Transmission in a form other

than speech is limited, and should be of a duration of less than 3

sec. as a compliance to ACA requirements in Australia.

This device complies with Standard Australia

Speciﬁcation No. AS/NZS4365-1996.

SUPPLIED ACCESSORY

• Belt clip ………………………………… 1

IC-4088S.qxd 03.10.2 8:20 Page ii (1,1)

iii

TABLE OF CONTENTS

FOREWORD …………………………………………………………………… i

IMPORTANT …………………………………………………………………… i

PRECAUTION ………………………………………………………………… i–ii

SUPPLIED ACCESSORY……………………………………………………… ii

TABLE OF CONTENTS ……………………………………………………… iii

1 PREPARATION …………………………………………………………… 1

■Belt clip attachment ……………………………………………………… 1

■Battery installation ……………………………………………………… 1

2 PANEL DESCRIPTION ………………………………………………… 2–4

■Switches, controls, keys and connectors ……………………………… 2

■Function display ………………………………………………………… 4

3 BATTERY CHARGING ………………………………………………… 5–7

■Battery caution …………………………………………………………… 5

■Charging connections …………………………………………………… 6

4 BASIC OPERATION …………………………………………………… 8–9

■Power ON ………………………………………………………………… 8

■Adjusting the volume …………………………………………………… 8

■Selecting the operating channel………………………………………… 9

5 RECEIVE AND TRANSMIT ………………………………………… 10–11

6 REPEATER FUNCTION ………………………………………………… 12

7 SCAN FUNCTION ………………………………………………………… 13

8 GROUP MODE (CTCSS) …………………………………………… 14–15

■Setting the group code ………………………………………………… 14

9 RING FUNCTIONS ……………………………………………………… 16

■Smart-Ring ……………………………………………………………… 16

■Call-Ring ………………………………………………………………… 16

10 OTHER FUNCTIONS ………………………………………………… 17–22

■Voice scrambler function ……………………………………………… 17

■Initial set mode ………………………………………………………… 17

■Lock function …………………………………………………………… 20

■Low battery indicator …………………………………………………… 20

■Auto power save………………………………………………………… 20

■ATS (Automatic Transponder System) ……………………………… 21

■Resetting the transceiver ……………………………………………… 21

■Optional HM-75A functions …………………………………………… 22

11 OPTIONS…………………………………………………………………… 23

12 SPECIFICATIONS …………………………………………………… 24–25

13 WARRANTY…………………………………………………………… 26–27

IC-4088S.qxd 03.10.2 8:20 Page iii (1,1)

PREPARATION

■Belt clip attachment

Attach the belt clip using the

supplied screw. Conveniently

attaches to a belt.

■Battery installation

Install 3 R6 (AA) size alkaline cell batteries or the optional BP-202

BATTERY PACK

as illustrated below.

qRemove the battery case

cover from the transceiver.

wInstall 3×R6 (AA) size alka-

line cell batteries or BP-

202.

• Be sure to observe the cor-

rect polarity.

NOTE: Keep battery contacts clean. It’s good idea to clean bat-

tery terminals once a week.

Alkaline cells

BP-202

IC-4088S.qxd 03.10.2 8:20 Page 1 (1,1)

2PANEL DESCRIPTION

■Switches, controls, keys and

connectors

Antenna

Function

display

(p. 4)

Speaker

Microphone

IC-4088S.qxd 03.10.2 8:20 Page 2 (1,1)

PANEL DESCRIPTION

qEXTERNAL SPEAKER AND MICROPHONE JACKS

Connect an optional speaker-microphone or headset, if desired.

wVOLUME CONTROL [VOL]

Rotate clockwise to increase and counterclockwise to decrease

volume.

ePTT SWITCH [PTT]

Push and hold to transmit; release to receive.

rMODE SWITCH [MODE]

➥Push to enter and select set mode for group (p. 14) and voice

scrambler code. (p. 17)

➥Push and hold for 1 sec. to turn the monitor function ON and

OFF. (p. 8)

tCHANNEL UP SWITCH [Y]

➥Push to increment the operating channel.

➥Push and hold to increment the operating channel continu-

ously.

➥While scanning, changes scanning direction. (p. 13)

yCHANNEL DOWN SWITCH [Z]

➥Push to decrement the operating channel.

➥Push and hold to decrement the operating channel continu-

ously.

➥While scanning, changes scanning direction. (p. 13)

uPOWER SWITCH [PWR]

➥Push to turn the power ON.

➥Push to switch between repeater and simplex operation.

(p. 12)

➥Push and hold this key to toggle the key lock function

ON/OFF. (p. 20)

iEXTERNAL DC IN JACK [DC 6V] (p. 6)

Connects the AC adapter or DC power cable for battery charg-

ing.

IC-4088S.qxd 03.10.2 8:21 Page 3 (1,1)

2PANEL DESCRIPTION

■Function display

qKEY LOCK INDICATOR

Appears during the key lock function ON.

wBUSY INDICATOR

Appears while receiving a signal or when the squelch is open.

eVOICE SCRAMBLER INDICATOR

Appears while the voice scrambler function is in use.

rREPEATER INDICATOR

Appears when repeater operation is selected.

tAUTO POWER OFF INDICATOR

Appears while the auto power off function is ON.

yLOW BATTERY INDICATOR

Appears or blinks when the battery decreases to a speciﬁed level.

uGROUP NUMBER INDICATOR

Indicates the selected group number during the group function ON.

iCHANNEL NUMBER INDICATOR

Indicates the selected operating channel number.

oPOWER ON INDICATOR

Appears while the power is ON.

!0 ANSWER BACK INDICATOR

➥

Appears when you and your group are in the conversation area.

➥Blinks when you or your group is out of the conversation area.

!1 TRANSMIT INDICATOR

Appears during PTT ON.

qewtry

uio!0

IC-4088S.qxd 03.10.2 8:21 Page 4 (1,1)

BATTERY CHARGING

■Battery caution

CAUTION NEVER short the terminals.

NEVER mix old and new batteries.

NEVER incinerate used battery cells. Internal battery gas may

cause explosion.

Make sure all battery cells are the same brand, type and capacity.

AVOID over charging—The BP-202 can be charged when the AC

adapter or the DC power cable with a DC power supply is con-

nected. To prevent over charging, the IC-4088S has charging timer

that automatically disconnecting the charging line electronically

after 15 hours from charging. However, the charging timer will reset

and start charging again when disconnect then re-connecting the

AC adapter or DC power cable more than 1 min. interval.

Recommended temperature range for charging: +10˚C to +40˚C

NEVER connect an AC adapter or DC power cable with an external

DC power supply that outputs lower than 5.7 V DC and more than

6.3 V DC voltage when charging the installed BP-202.

The optional BP-202

BATTERY PACK

includes rechargeable Ni-Cd

batteries and can be charged approx. 300 times. Charge the battery

pack before ﬁrst operating the transceiver or when the battery pack

becomes exhausted.

If the battery pack seems to have no capacity even after being fully

charged, completely discharge it by leaving the power ON all day.

Then, fully charge the battery pack again.

If the battery pack still does not retain a charge (or very little), a new

battery pack must be purchased.

DDOperating period

Depending on the installed battery, the operating period of the

transceiver varies. Refer to p. 24 for operating period details.

IC-4088S.qxd 03.10.2 8:21 Page 5 (1,1)

3BATTERY CHARGING

■Charging connections

DDRegular charging via [DC 6V] jack

➥Connect the AC adapter or DC power cable with an external DC

power supply to [DC 6V].

•The supplied voltage must be within the range of 5.7 to 6.3 V

DC.

•Charging period: approx. 15 hours

IMPORTANT!:

Use the AC adapter or DC power cable with an external DC

power supply (6.0 V DC ±0.3 V), which speciﬁed by Icom Aus-

tralia, ONLY. Other type of AC adapter or DC power cable with

an external power supply may damage the transceiver.

The optional BP-202 can only be charged—other AA (R6) size

rechargeable Ni-Cd cannot be charged.

to [DC 6V]

jack

DC power cable

AC adapter

to a DC power supply

to AC outlet

Turn the power OFF!

When the installed Ni-Cd

battery is nearly exhausted

and the function display

blinks in intermittently,

push [PWR] until the trans-

ceiver’s power goes OFF.

*About the plug

Polarity:

Outer: 4.0±0.1 mm (d)

Inner: 1.7±0.05 mm (d)

Length: 9.5±0.5 mm

IC-4088S.qxd 03.10.2 8:21 Page 6 (1,1)

Tabla de contenidos

Otros manuales de Transceptor de Icom

Icom

Icom IC-9700 Instrucciones de instalación y funcionamiento

Icom

Icom IC-7700 Guía

Icom

Icom IC-M59euro Manual de usuario

Icom

Icom iF3002 Manual de usuario

Icom

Icom IC-M120 Manual de usuario

Icom

Icom IC-F9511HT Manual de usuario

Icom

Icom IC-F3162DT Manual de usuario

Icom

Icom IC-M88 Manual de instrucciones

Icom

Icom IC-A110EURO Manual de usuario

Icom

Icom D-STAR ID-31A; D-STAR ID-31E Manual de usuario

Icom

Icom IC-F29DR Manual de usuario

Icom

Icom iM400BB Manual de usuario

Icom

Icom iF110 Manual de usuario

Icom

Icom CS-207 Manual de usuario

Icom

Icom ID-1 Instrucciones de instalación y funcionamiento

Icom

Icom IC-78 Instrucciones de montaje

Icom

Icom IC-F5400DP Series Manual de usuario

Icom

Icom IC-F12 Manual de usuario

Icom

Icom IC-E2820 Manual de usuario

Icom

Icom D-STAR ID-4100A Manual de usuario

Icom

Icom IC-F4101D Manual de usuario

Icom

Icom IC-M36 Manual de usuario

Icom

Icom IC-iF3161 Manual de usuario

Icom

Icom IC-4AT Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario