Icom Ic-2730A Manual del propietario

©June 2016 Icom America Inc. Page 1

Icom America, Inc.

12421 Willows Road NE

Kirkland, WA 98034

IC-2730A Memory Channel Programming

This programming method uses the front panel keys.

What you will need:

•Operating frequency

•Offset direction (Duplex, for repeater use)

•Subaudible tone frequency for your repeater

Entering a Frequency

1. Press the Main/Band key to select the side of the display you wish to use (MAIN will appear on

the selected side).

2. Press the [V/MHz/Scan] key to place the radio in VFO mode.

3. Rotate the dial (for the side of the radio you selected) to enter your frequency.

4. Press [Menu] to enter the menu selection mode.

Selecting the Repeater Tone

1. Rotate the dial to select R TONE.

2. Press the Enter key (the key below a backwards-facing arrow: [MW]). You will see R TONE to

the left of the display and the value of the subaudible tone on the right side.

3. Rotate the dial to select the repeater tone.

4. Press the Enter key.

Turning on the Tone Encoder

Use the dial to select TONE and press the Enter key. The letter Twill appear on the display above the

frequency to show that the tone encoder is enabled.

Setting the offset (DUPLEX)

1. Press and hold the key labeled [MONI/DUP]. You will see an indication of the Duplex direction

(-, +or OFF).

2. Select the offset direction by rotating the dial.

3. When you have the correct offset direction, press the [MONI/DUP] key again.

©June 2016 Icom America Inc. Page 2

Icom America, Inc.

12421 Willows Road NE

Kirkland, WA 98034

Saving these settings to Memory

Your display should show your frequency, the duplex (DUP+or DUP-), and the Tfor tone encoder. To

save these settings to a Memory Channel, do the following:

1. Press the [MW] key.

2. MW will blink on the display.

3. Rotate your dial to display CH SEL (channel selection).

4. Press the Enter key.

5. Rotate the dial to the memory channel you wish to use.

6. Press the Enter key.

7. Rotate the dial to WRITE.

8. Press the Enter key.

9. The display will show WRITE.

10. Rotate the dial to YES.

11. Press the Enter key.

Verify the Programming

To check the memory channels, momentarily press the [MR/CALL] key and rotate the dial through the

memory channels and confirm that the repeater is programmed into the memory channel that you

selected.

Otros manuales para ic-2730A

2

Tabla de contenidos

Otros manuales de Transceptor de Icom

Icom

Icom IC-F3161DT Manual de usuario

Icom

Icom IC-707 Manual de usuario

Icom

Icom IC-M31 Manual de usuario

Icom

Icom IC-GM800 Manual de usuario

Icom

Icom IC-M601 Manual de usuario

Icom

Icom IC-U8 Manual de usuario

Icom

Icom IC-756PROIII Manual de usuario

Icom

Icom IC-3SAT Manual de usuario

Icom

Icom IC-T81E Manual de usuario

Icom

Icom IC-80AD Manual de usuario

Icom

Icom IC-7700 Manual de usuario

Icom

Icom IC-730 Manual de usuario

Icom

Icom IC-H10 Manual de usuario

Icom

Icom IC-V82 Manual de usuario

Icom

Icom IC-751A Manual de usuario

Icom

Icom IC-M504 Manual de usuario

Icom

Icom IC-4008E Manual de usuario

Icom

Icom IC-271A Manual de usuario

Icom

Icom IC-W31A Manual de usuario

Icom

Icom ID-5100A Manual de usuario

Icom

Icom IC ?2A Manual de usuario

Icom

Icom IF1721/D Manual de usuario

Icom

Icom IC-U82 Instrucciones de instalación y funcionamiento

Icom

Icom IC-2725E Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario