IBM DTTA-350320 Manual de usuario

Page 1 Version 3.0

Installation Guide

DESKSTAR 14GXP

DESKSTAR 16GP

Models

DTTA-350320 DTTA-371010

DTTA-350430 DTTA-371290

DTTA-350640 DTTA-371440

DTTA-350840

DTTA-351010

DTTA-351290

DTTA-351680

Table of Contents

Page 27

Glossary

...............................................................

Page 26

Compatibility Matrix

....................................................

Page 25

Drive Copy

............................................................

Page 25

Utilities

................................................................

Page 24

Backup & Restore

.....................................................

Page 24

Controller Information

..................................................

Page 24

Jumper Block Information

..............................................

Page 23

Making a Bootable DOS Diskette

.......................................

Page 22

Automated Fax Back Service

...........................................

Page 22

Technical Support

.....................................................

Page 21

Operating system installation tips

.......................................

Page 20

File Systems

...........................................................

Page 19

Formatting

.............................................................

Page 17

FDISK

.................................................................

Page 15

BIOS Settings

..........................................................

Page 15

Custom Installation

....................................................

Page 12

Easy Installation

.......................................................

Page 11

Connectors

............................................................

Page 10

Mounting

..............................................................

Page 8

Jumper Settings

.......................................................

Page 8

Unpackaging your hard drive

...........................................

Page 8

Opening your computer

................................................

Page 8

Installation

.............................................................

Page 7

Hardware Description

..................................................

Page 7

Installation Kit

.........................................................

Page 6

Installation Checklist

...................................................

Page 5

Hard Disk Drive Handling Guide

........................................

Page 3

Hard Disk Drive Installation Flowchart

.................................

Page 2

Technical Support

.....................................................

Technical Support

http://www.ibm.com/harddrive

888.426.5214

Page 2 Version 3.0

Hard Disk Drive Installation Flowchart

Step 1

Assemble needed equipment

Page 6

Step 2

Remove cover of your computer

Page 8

Step 3

Set jumpers

Page 8

Set jumpers for Master or

Standalone

(Shipping Default)

Page 8

Set jumpers for Slave

Page 8

Step 5

Connect IDE and power

cables to drive

Page 11

Add-on Ultra DMA

Controller

Page 11

On board IDE

Ports

Page 11

Secondary

Port

Page 11

Primary

Port

Page 11

Step 4

Mount drive securely

Page 10

Step 6

Connect IDE

cable to

computer

Page 11

Step 7

Replace cover on computer

Page 12

Step 8

Replace system cables

Page 12

Installation

Page 12

Step 9a

Easy Install

Page 12

Step 9b

Custom Install

Page 15

Boot from Ontrack® Disk

Manager Diskette

Page 12

Select Easy Disk Installation

Page 12

Complete Installation

Page 13

Check BIOS settings for full

capacity

Page 15

Boot from bootable diskette

Page 17

FDISK

Page 17

Format

Page 19

Step 10

Install Operating System if required

Page 21

Page 3 Version 3.0

HARDWARE INSTALLATION AND DRIVE PREPARATION MANUAL

FOR IBM HARD DISK DRIVES

This manual has been prepared to help you install your IBM Deskstar 14GXP or Deskstar 16GP hard drive

in most computer systems. If you feel uncomfortable installing this drive yourself, take it to a qualified

installer.

International Business Machines Corporation provides this publication "AS IS" without warranty of any kind,

either express or implied, including, but not limited to, the implied warranties of merchantability or fitness for

a particular purpose. Some states do not allow disclaimers of express or implied warranties in certain

transactions, therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Product data and specifi-

cations are subject to change without notice. Changes are periodically made to the information herein;

these changes will be incorporated in new editions of the publication. IBM may make improvements and/or

changes in the product(s) and/or the program(s) described in this publication at any time.

It is possible that this publication may contain reference to, or information about, IBM products (machines

and programs), programming, or services that are not announced in your country. Such references or

information must not be construed to mean that IBM intends to make available such IBM products, pro-

gramming, or services in your country.

Product description data contained herein represents IBM’s design objectives and is provided for compari-

son among IBM products; actual results may vary based on a variety of factors. The product data

contained herein does not constitute a warranty. Questions regarding IBM warranty terms or the method-

ology used to derive data should be referred to an IBM representative.

Technical information about IBM hard disk drive products can be found on the web at

http://www.ibm.com/harddrive or by calling IBM hard disk drive technical support at 888.426.5214

Government Users - Documentation related to restricted rights - Use, duplication or disclosure is subject to

restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

IBM is a registered trademark of the International Business Machines Corporation. The following are also

trademarks or registered trademarks of the International Business Machines Corporations in the United

States, other countries, or both: Deskstar, OS/2, and Surepath. Any other products or trademarks are the

property of their respective owners.

Page 4 Version 3.0

Before you begin, please read the following on handling your disk drive:

HARD DISK DRIVE HANDLING GUIDE

These notes are designed to provide a simple overview of the need to be cautious when

handling a disk drive.

Disk drives can be easily damaged either by electrical static shock or by rough handling. In order to

minimize the risks it is essential that any disk drive be handled on a cushioned surface (which is

electrostatically safe). Many such static safe mats are available, examples are 3M's 8210 table mat or

3M's "First Touch" computer pad. Great care should be taken when handling disk drives - treat them like

fragile eggs. Do not bump them against any object. When attaching brackets or mounting the drive in the

computer, be very careful. It is VERY EASY to introduce shocks which exceed the specification.

Please note that the robustness for each disk drive to withstand electrical or mechanical shock is different,

depending on its design. The hard disk drive technical support center can advise you on the suitability of

your Deskstar drive for a specific application.

Damage might not be immediately evident and may cause the drive to fail months later.

Page 5 Version 3.0

Step 1: Installation Checklist

To install the Deskstar drive you may need the following depending on your computer:

1) __ The installation kit that came with your Deskstar drive containing 4 mounting screws,

IDE cable, Ontrack® Disk Manager and any related publications. Save the box the

drive came in.

2) __ The documentation that came with your computer or storage enclosure.

3) __ A small, flat-blade screwdriver.

4) __ An IDE controller, which is either built in or an adapter inside your computer. Have

documentation readily available for your IDE controller also.

5) __ Mounting brackets, if required for your computer. Contact your place of purchase if you

are unsure if mounting brackets are required.

6) __ A bootable DOS diskette. (If one is not available to you, see instructions for making a

bootable DOS diskette in the appendix.) The Ontrack® diskette is bootable.

7).__ If you are replacing an older internal drive with the new Deskstar drive and want to copy all of the

files from the older drive to your new one, you may need additional software. (See the section on

Drive Copy on page 25 for information.)

Continue installation with the following procedures:

1) __ Backup your existing drive to avoid any loss of data during installation.(see Backup & Restore on

page 24) After completing backup, shut down as normal.

2) __ Unplug your system from the electrical outlet.

3) __ Establish a common voltage between you and the hard drive. Touch an unpainted metal

surface on the outside of your system with your bare hands and the hard drive in it’s

anti-static bag simultaneously. Avoid excessive movement until the drive has been mounted.

4) __ DO NOT LOW-LEVEL FORMAT YOUR IDE DRIVE! IDE drives are low-level formatted by the

manufacturer and reformatting may cause permanent damage to yourdrive and your system.

(See Utilities on page 25)

5) __ Record the following information:

Drive Model ________________ Date of Purchase_________________

Drive P/N __________________ Place of Purchase_________________

Serial # ____________________

If you currently have a hard drive in your system you may want to record the CMOS settings. This

information is in your BIOS setup. You can enter your BIOS setup by pressing the key sequence for your

system while booting. (See BIOS on page 15)

Cylinders _______________________ Sectors/Track_____________________

Heads __________________________ Landing Zone _____________________

Write Pre Comp (if you have this category) __________________

Page 6 Version 3.0

Installation Kit

The DTTA model drives come complete with 4 screws for mounting, an IDE cable and an installation guide.

It also comes with Ontrack® Disk Manager and any related publications.

Hardware Description

The Deskstar 16GP and 14GXP family has an advanced Ultra ATA interface and supports transfer rates of

up to 33.3 MB/sec. To take advantage of the higher transfer rate of 33.3 MB/sec, your computer will need

to have a controller that supports the Ultra ATA interface. If you have an older interface such as Multi-word

DMA Mode-2 or PIO Mode-4, the drive will work, but will be limited in data transfer speed due to the lower

speed of your controller. If you have a slower controller, you may choose to purchase a UltraDMA

controller card (fits into one of the available slots in your computer) to take advantage of Deskstar’s

33.3MB/sec data transfer rate. To determine if your current controller card is Ultra DMA, see the

documentation that came with your system or contact the computer manufacturer for information.

Whether you use your desktop computer for audio and video editing, computer-aided design and

manufacturing (CAD/CAM), 3D graphics, animation and photo manipulation, web page design, or data

mining and data warehousing - advanced desktop applications such as these demand an advanced data

storage solution. These drives are 3.5" drives designed to work in Entry Servers, Entry Workstations and

Desktop personal computers. The Deskstar 16GP is available in capacities of 3.2, 4.3, 6.4, 8.4, 10.1, 12.9

and 16.8 GB running at 5400 RPM. The Deskstar 14GXP is available in capacities of 10.1, 12.9 and 14.4

GB and runs at 7200 RPM. The Deskstar 14GXP and Deskstar 16GP families are designed to work with

MMX systems. Compatibility listings are included in the appendix.

Page 7 Version 3.0

Installation

Guide

Ontrack

Jumpers

Screws

Screwdriver

Disk Manager

IDE Cable

Installation

Guide

Hard Drive

Step 2: Installation

Opening your computer

1. Turn the system off.

2. Unplug the power cord from the wall outlet.

3. Remove all cables from the back of your computer, labeling them if necessary.

4. Remove the cover from your computer. (Consult your user's guide for instructions if needed.)

Unpackaging your hard drive

1. Remove the drive from the anti-static package that it was shipped in.

2. Handle the drive by the sides only.

3. Do not touch the main computer chip board.

4. Do not drop. A drop from only 1/4 inch could permanently damage your hard drive.

5. If available, use an ESD (Electronic Static Discharge) wrist strap while handling your drive.

6. Place the drive carefully on a static free area.

Step 3: Jumper Settings

The jumper settings are found on the hard drive next to the interface connector. (See diagram on page 9)

They are physical settings that you need to change for different uses of your hard drive. If your drive will

be used as a single drive or as a boot drive, no changes are required. The drive is shipped with jumpers

set to Master. If you wish your drive to be the Master drive, skip to Mounting on page 10.

Decide how you want to set up your drive. Will it be the only drive in the system? Will it be in a system

that has an existing drive?

Single drive - Master setting

Use this setting if you are replacing your old drive with the new Deskstar drive and you

will not be using your old drive.

Put a jumper on pins A-B & G-H to make this drive the only drive in your system.

(Shipping default is 'Master' setting - 16 heads)

Second drive - Master setting (boot drive)

Put a jumper on pins A-B & G-H.

(Note: If your BIOS setup does not detect the slave drive, you may need to use the

SLAVE present setting by placing a jumper on pins E-F & G-H.)

Second drive - Slave setting

Use this setting if you want to retain your old drive as the boot drive and have the new

drive available for program and data storage.

Put the jumper on pins A-B & C-D.

Cable Select -

This setting should be used if your system uses special “cable select” cables.

Page 8 Version 3.0

Interface Connector Power Connector

Jumper Block

Jumper Block Location

Some BIOSs have a limitation when translating the Cylinder, Head, and Sector information resulting in an

inability to correctly detect the larger capacity drives. Most systems don’t have this limitation but if your

BIOS is reporting the capacity incorrectly, use the 15 logical head settings rather than the 16 logical heads.

Settings are shown below.

I G

ECA

Interface

Connector Power

Connector

I G

ECA

I G

ECA

I G

ECA

I G

ECA

I G

ECA

I G

ECA

I G

ECA

I G

ECA

16 Logical Head 15 Logical Head

Device 0 (Master)

(Shipping default)

Device 1 (Slave)

Cable Select

Device 0

(Slave present)

Device 0 (Master)

(Shipping default)

Device 1 (Slave)

Cable Select

Device 0

(Slave present)

Jumper settings

Page 9 Version 3.0

Step 4: Mounting

After setting the jumpers, mount the hard drive in your system. The DTTA drive can be mounted with any

of its six surfaces facing down (right side up, upside down, sideways, etc.). See below for mounting hole

locations. Be sure to treat the disk drive very carefully and gently.

You must ensure that the drive has sufficient air flow. Mount the drive in the system using the 4 6-32 UNC

screws (included). The maximum screw length is 3.5 mm for the side holes and 6 mm for the bottom

holes. Mount the drive securely enough to prevent it from excessive motion or vibration.

If you are mounting your drive in a 5” bay, you may need to purchase mounting brackets from your

computer manufacturer for the drive to be mounted securely.

Mounting hole locations

Page 10 Version 3.0

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de IBM

IBM

IBM RDX Manual de usuario

IBM

IBM Storwize V7000 Manual de funcionamiento

IBM

IBM Netfinity EXP300 Manual del propietario

IBM

IBM System storage DS6000 Series Manual de usuario

IBM

IBM System Storage TS7600 ProtecTIER Series Manual de instalación y operación

IBM

IBM 1 GB Microdrive Storage Card Manual de usuario

IBM

IBM DS3500 Manual de usuario

IBM

IBM Storwize V7000 Manual de usuario

IBM

IBM T400 Manual de instrucciones

IBM

IBM 3581 Manual de usuario

IBM

IBM 8275-416 Guía de referencia

IBM

IBM Storwize V5000 Gen2 Manual de usuario

IBM

IBM 1 GB Microdrive Storage Card Manual de usuario

IBM

IBM Storwize V7000 Manual de usuario

IBM

IBM Accesser 4105 Manual de usuario

IBM

IBM Slicestor 2584 Manual de usuario

IBM

IBM DARA-206000 - Travelstar 12 GB Hard Drive Manual de usuario

IBM

IBM Deskstar Deskstar 5 Manual de usuario

IBM

IBM 353 Manual de usuario

IBM

IBM Storwize V7000 Manual de usuario

IBM

IBM XIV STORAGE SYSTEM Manual

IBM

IBM SYSTEM STORAGE EXP3000 - INTEROPERABILITY MATRIX... Manual de usuario

IBM

IBM Travelstar 10GT Manual de usuario

IBM

IBM TotalStorage DS300 Instrucciones de uso

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario