IBM X3850 X6 Manual de usuario
System x3850 X6 and x3950 X6
Types3837and3839
Rack Installation Instructions
System x3850 X6 and x3950 X6
Types3837and3839
Rack Installation Instructions
Second Edition (June 2014)
© Copyright IBM Corporation 2014.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
Chapter 1. Safety information .....1
Chapter 2. Rack kit parts inventory . . . 3
Chapter 3. Rack installation ......5
Identifying the rack space for the server .....5
Opening the rails .............8
Installing the rails in the rack .........9
Installing the server in the rack ........10
Fastening the server in the rack........13
Installing the shipping brackets........14
Attaching the cable management brackets and
routing the cables ............15
Removing the server from the rack ......16
© Copyright IBM Corp. 2014 iii
iv System x3850 X6 and x3950 X6 Types 3837 and 3839: Rack Installation Instructions
Chapter 1. Safety information
Review the documentation that comes with the rack cabinet for safety and cabling
information. Before you install the server in a rack cabinet, review the following
guidelines.
Note: Use the M5 screws that come with the rails to install the server in a rack
cabinet if you plan to transport the rack cabinet to another location with the server
installed or if the rack is in a vibration-prone area.
vMake sure that the room air temperature is below 40°C (104°F).
vDo not block any air vents; usually, 15 cm (6 in.) of air space in the rear and 5
cm (2 in.) in the front provides proper airflow.
vTwo or more people are required to install the device in a rack.
vDo not leave any unused space within a rack open. Fillers must be used to
prevent recirculation of warm air.
vInstall your server only in a rack that has perforated front and rear doors or in a
rack that is equipped with an IBM®Rear Door Heat eXchanger.
vDo not extend more than one device out of the rack at the same time.
vRemove the rack doors and side panels to provide easier access during
installation.
vThe EIA flanges must have holes and clearances per EIA-310-D.
vIf you have a rack with adjustable depth EIA rails, set the distance between the
rails to no more than 719 mm (28.3 inches) outside to outside in order to allow
space to install the cable management brackets onto the rear of the system.
vMake sure that there is sufficient room in front of the front EIA flange to provide
minimum bezel clearance of 50 mm (1.97 inches).
vMake sure that there is sufficient room behind the rear of the rear EIA flanges to
provide for cable management and routing.
vRack weight-handling capacity must be sufficient for the aggregate weight of the
server, power distribution units, and power cables.
vThe rack must be stabilized with stabilization brackets and leveling pads so that
it does not become unstable when it is fully populated.
Rack Safety Information, Statement 2
© Copyright IBM Corp. 2014 1
DANGER
vAlways lower the leveling pads on the rack cabinet.
vAlways install stabilizer brackets on the rack cabinet.
vAlways install servers and optional devices starting from the bottom of the
rack cabinet.
vAlways install the heaviest devices in the bottom of the rack cabinet.
Statement 4
CAUTION:
Use safe practices when lifting.
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
Statement 26
CAUTION:
Do not place any object on top of rack-mounted devices.
2System x3850 X6 and x3950 X6 Types 3837 and 3839: Rack Installation Instructions
Chapter 2. Rack kit parts inventory
This topic provides information about the items in the rail kit and rack installation
kit.
The information and instructions in this document apply to both the System x3850
X6 and the System x3950 X6 servers.
A rail kit comes with the items that you need to install the server in a rack. Open
the rail kit and the rack installation kit. If items are missing or damaged, contact
your place of purchase.
The rail kit box includes the following hardware. This kit ships with the server.
vOne right server support rail
vOne left server support rail
vEight M5 hex head screws
vTen hook and loop straps
Left rail
LEFT FRONT
Right rail
Hook and loop
fasteners
(x10)
M5 hex
head screws
(x8)
The cable management bracket kit includes the following hardware. This kit ships
with the server.
vOne right cable management bracket (two for 8U system)
vOne left cable management bracket (two for 8U system)
Left cable
management
bracket
Right cable
management
bracket
The optional shipping bracket kit includes the following hardware. You can
purchase this kit separately.
© Copyright IBM Corp. 2014 3
vEight M5 cage nuts (use on EIA flanges with square holes)
vEight M5 clip nuts (use on EIA flanges with round holes)
vEight M5 hex head screws
vTwo shipping brackets
Shipping
brackets (x2)
M5 clip
nut (x8)
M5 cage
nut (x8)
Hex head
screw (x8)
The server might also come with an additional bag with M5 screws, cage nuts, and
clip nuts.
4System x3850 X6 and x3950 X6 Types 3837 and 3839: Rack Installation Instructions
Otros manuales para X3850 X6
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Servidor de IBM
IBM
IBM 86655RY - Netfinity 7600 - 8665 Manual del propietario
IBM
IBM xSeries 455 Manual de usuario
IBM
IBM System x3650 Type 7979 Manual de usuario
IBM
IBM Flex System x440 Compute Node Instrucciones de instalación y mantenimiento
IBM
IBM 79473AU Manual de usuario
IBM
IBM 86857RX Manual de usuario
IBM
IBM E Server i Series Manual de usuario
IBM
IBM x3105 - System - 4347 Manual de usuario
IBM
IBM Power System 9223-42S Manual de usuario
IBM
IBM xSeries 345 Manual de usuario
IBM
IBM Power System 9009-22G Manual de usuario
IBM
IBM 6C4 Manual de usuario
IBM
IBM 9407-515 Manual de usuario
IBM
IBM 7944E2U Manual de usuario
IBM
IBM NeXtScale nx360 M4 Instrucciones de instalación y mantenimiento
IBM
IBM pSeries 615 Model 6C3 Manual de usuario
IBM
IBM System x3650 M4 Type 7915 Manual de usuario
IBM
IBM System x3650 M3 4255 Manual de usuario
IBM
IBM eServer 445 xSeries Manual de usuario
IBM
IBM System x3100 M4 Manual de usuario
