IBM 4-Port 10/100 Base-TX Ethernet PCI Guía
4-Port 10/100 Base-TX Ethernet PCI Adapter
Installation and Using Guide
SA23-2567-02
Third Edition (September 2001)
Before using this information and the product it supports, read the information in “Safety Information” on page v and
“Appendix B. Notices” on page 25.
A reader’s comment form is provided at the back of this publication. If the form has been removed, address comments
to Publications Department, Internal Zip 9561, 11400 Burnet Road, Austin, Texas 78758-3493. To send comments
electronically, use this commercial internet address: [email protected]. Any information that you supply may
be used without incurring any obligation to you.
©International Business Machines Corporation 1998, 2001. All rights reserved.
Note to U.S. Government Users Restricted Rights--Use, duplication or disclosure restricted by GSA ADP Schedule
Contract with IBM Corp.
Note
Before using this information and the product it supports, be sure to read the general information
under ″Product Warranties and Notices″included with your system unit.
Contents
Safety Information.......................v
Handling Static Sensitive Devices.................vii
About This Book .......................ix
ISO 9000 ..........................ix
Related Publications ......................ix
Trademarks .........................ix
Chapter 1. Overview ......................1
Understanding the Adapter LEDs ..................1
Software Requirements .....................2
Chapter 2. Preparing for Installation ................3
Verifying Your Hardware Requirements ................3
Checking Prerequisites .....................3
Chapter 3. Installing the Device Driver Software ............5
Chapter 4. Installing the Device Driver on the RS/6000 SP System......7
Checking System Prerequisites...................7
Installing Software on the Control Workstation .............10
Installing Device Drivers on the SP Nodes...............11
Chapter 5. Updating System Firmware ...............13
Chapter 6. Installing the 4-Port 10/100 Base-TX Ethernet PCI Adapter ....15
Installing the Adapter......................15
Verifying the Installation .....................15
Verifying Adapter Hardware Installation...............15
Verify AIX Software Installation .................16
Running Adapter Diagnostics ...................17
Chapter 7. Connecting to an Ethernet Network ............19
Connecting the Network Cables and Adapter ..............19
Appendix A. Communications Statements ..............21
Federal Communications Commission (FCC) Statement ..........21
European Union (EU) Statement ..................21
International Electrotechnical Commission (IEC) Statement .........22
United Kingdom Telecommunications Safety Requirements .........22
Avis de conformité aux normes du ministère des Communications du Canada. . . 22
Canadian Department of Communications Compliance Statement .......22
VCCI Statement .......................22
Electromagnetic Interference (EMI) Statement - Taiwan ..........23
Radio Protection for Germany ...................23
iii
Safety Information
DANGER
An electrical outlet that is not correctly wired could place hazardous voltage
on metal parts of the system or the devices that attach to the system. It is the
responsibility of the customer to ensure that the outlet is correctly wired and
grounded to prevent an electrical shock.
Before installing or removing signal cables, ensure that the power cables for
the system unit and all attached devices are unplugged.
When adding or removing any additional devices to or from the system,
ensure that the power cables for those devices are unplugged before the
signal cables are connected. If possible, disconnect all power cables from the
existing system before you add a device.
Use one hand, when possible, to connect or disconnect signal cables to
prevent a possible shock from touching two surfaces with different electrical
potentials.
During an electrical storm, do not connect cables for display stations, printers,
telephones, or station protectors for communications lines.
v
vi 4-Port 10/100 Base-TX Ethernet PCI Adapter: Installation and Using Guide
Handling Static Sensitive Devices
Attention: Static electricity can damage this device and your system unit. To avoid
damage, keep this device in its anti-static protective bag until you are ready to install it.
To reduce the possibility of electrostatic discharge, follow the precautions listed below:
vLimit your movement. Movement can cause static electricity to build up around you.
vHandle the device carefully, holding it by its edges or its frame.
vDo not touch solder joints, pins, or exposed printed circuitry.
vDo not leave the device where others can handle and possibly damage the device.
vWhile the device is still in its anti-static package, touch it to an unpainted metal part
of the system unit for at least two seconds. (This drains static electricity from the
package and from your body.)
vRemove the device from its package and install it directly into your system unit
without setting it down. If it is necessary to set the device down, place it on its
static-protective package. (If your device is an adapter, place it component-side up.)
Do not place the device on your system unit cover or on a metal table.
vTake additional care when handling devices during cold weather, as heating reduces
indoor humidity and increases static electricity.
vii
viii 4-Port 10/100 Base-TX Ethernet PCI Adapter: Installation and Using Guide
About This Book
This book provides information about installing the 4-Port 10/100 Base-TX Ethernet PCI
Adapter and device driver support software, as well as how to attach the adapter to a
network. Use this book in conjunction with your specific system unit and operating
system documentation.
ISO 9000
ISO 9000 registered quality systems were used in the development and manufacturing
of this product.
Related Publications
The following publications contain related information:
vSystem unit documentation for information specific to your hardware configuration
vOperating system documentation for information specific to your software
configuration. This documentation is located on the AIX V4.3 Documentation CD. The
documentation information is made accessible by loading the documentation CD onto
the hard disk or by mounting the CD in the CD-ROM drive.
v
PCI Adapter Placement Reference
, SA38-0538 (for the latest version, you may need
to contact your marketing representative)
Trademarks
The following terms are trademarks of International Business Machines Corporation in
the United States, other countries, or both:
vAIX
vRS/6000
vSP
Other company, product, and service names may be trademarks or service marks of
others.
ix
x4-Port 10/100 Base-TX Ethernet PCI Adapter: Installation and Using Guide
Tabla de contenidos
Otros manuales de Adaptador de IBM
IBM
IBM Flex System EN4132 Manual de usuario
IBM
IBM N2125 Manual de instalación
IBM
IBM 4684 Store Loop Adapter/A Manual de usuario
IBM
IBM Advanced SerialRAID Adapters SA33-3285-02 Manual de usuario
IBM
IBM Flex System FC3052 Manual de usuario
IBM
IBM ThinkPad 600 Manual de usuario
IBM
IBM 16/4 Token-Ring Manual de usuario
IBM
IBM 10/100/1000 Base-TX Ethernet PCI-X Adapter Guía
IBM
IBM ServeRAID Manual de usuario
IBM
IBM Flex System FC5054 Manual de usuario
IBM
IBM 74Y4064 Manual de usuario
IBM
IBM RedbooksQLogic 8200 Manual de usuario
IBM
IBM TotalStorage FAStT FC2-133 Manual de usuario
IBM
IBM ThinkPad i Series Manual de usuario
IBM
IBM Turboways 155 Manual de usuario
IBM
IBM Power GXT800P Manual de usuario
IBM
IBM TOKEN-RING PCI FAMILY ADAPTER Manual de usuario
IBM
IBM Emulex Virtual Fabric Adapter Manual de usuario
IBM
IBM TURBOWAYS 622 PCI MMF ATM Guía
IBM
IBM Emulex Manual de usuario
