iBell Tools EB60-69 Manual de usuario


1

2
1. GENERAL SAFETY WARNINGS _________________________
2. ELECTRIC BLOWER SAFETY WARNINGS _______________
3. PRODUCT OVERVIEW _________________________________
4. PRODUCT SPECIFICATIONS ___________________________
5. SETUP ________________________________________________
6. GENERAL OPERATION ________________________________
7. TROUBLESHOOTING __________________________________
TABLE OF CONTENTS
IBL EB 60-69
3
6
7
8
9
10
13

3
Do not operate blowers in explosive atmospheres, such as in
the presence of flammable liquids or gases
Keep work area well lit.Cluttered or dark areas invite accidents.
Keep children and bystanders away while operating a blower.
Distractions can cause you to lose control.
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the blower. Keep it away from heat, oil, sharp
edges or moving parts.
Blower plugs must match the outlet. Never modify the plug in
any way. Modified plugs and un-matching outlets will increase the
risk of electric shock.
Avoid body contact with earthed or grounded surfaces. There is
an increased risk of electric shock if your body is earthed or
grounded.
Do not expose blowers to rain or wet conditions. Water entering
a blower will increase the risk of electric shock.
When operating a blower outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
GENERAL SAFETY WARNINGS
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this product.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury. Save all warnings and
instructions for future reference.
WORK AREA SAFETY
ELECTRICAL SAFETY
IBL EB 60-69

4
Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes,
hard hat, or hearing protection used for appropriate conditions
will reduce personal injuries.
Stay alert, watch what you are doing and use common sense
when operating a blower. Do not use a blower while you are tired
or under the influence of drugs or alcohol. A moment of inattention
while operating blowers may result in serious personal injury.
Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery pack,
picking up or carrying the tool.
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the blower in unexpected situations.
Dress properly, say no to loose clothing or jewellery. Keep your
hair, clothing away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and
properly used.
Have your blower serviced by a qualified repair-person using
only identical replacement parts.This will ensure that the safety
of the blower is maintained.
When servicing a blower, use only identical replacement parts.
Follow instructions in the maintenance section of this manual. Use
of unauthorized parts or failure to follow maintenance instructions
may create a risk of shock or injury.
PERSONAL SAFETY
IBL EB 60-69
SERVICE

5
Do not force the blower. Use the correct blower for your
application. The correct blower will do the job better and safer at
the rate for which it was designed.
Do not use the blower if the switch does not turn it on and off.
Any blower that cannot be controlled with the switch is dangerous
and must be repaired.
Disconnect the plug from the power source and/or the battery
pack from the blower before making any adjustments, changing
accessories, or storing blowers. Such preventive safety measures
reduce the risk of starting the blower accidentally.
Store blowers out of the reach of children and do not allow
persons unfamiliar with the blower or these instructions to
operate the blower. Blowers could be dangerous.
Keep handles and grasping surfaces dry, clean and free from oil
and grease. Slippery handles and grasping surfaces do not allow
for safe handling and control of the tool in unexpected situations.
Even if you are operating this product in accordance with all the
safety requirements, potential risks of injury and damage remain.
The following dangers can arise:
Health defects resulting from vibration emission if the product is
being used over long periods of time or not adequately managed
and properly maintained.
Injuries and damage to property due to broken cutting attachments
or the sudden impact of hidden objects during use.
Danger of injury and property damage caused by other objects or
due to natural reactions or calamities.
USE AND CARE
IBL EB 60-69
RESIDUAL RISKS

6
This electric blower is a dual function device designed for blowing
and sucking in the around the garage, shop or home. It can be used
to remove small debris, dust, shavings, leaves, or blow dry water
on a smooth surface. Not recommended for rough, porous or
uneven surfaces. This device is not designed for industrial
applications. The device cannot be used for other purposes than
its intended use.
Always wear sturdy shoes and sufficient clothing during
operation. Do not wear loose clothing that can be sucked into
the suction tube.
Keep long hair away from air intakes. Always use personal
protective equipment, such as safety glasses and hearing
protection.
Never block suction inlet and outlet. Do not place the inlet or
outlet of the vacuum near eyes or ears when operating. Never blow
debris in the direction of bystanders.
Do not cross gravel paths or roads whilst your product is switched
on during blow/vac mode. Walk, never run with the product.
Do not collect cigarette ashes, freshly cut metals shaving, screws,
nails and the like.
Always be sure of your footing, particularly on slopes. Do not
overreach and keep your balance at all times.
Wear protective goggles while operating. To protect your feet and
legs while operating the appliance, always wear heavy duty
footwear and long trousers.
If operating an appliance in a damp location is unavoidable, use a
Residual Current Device (RCD) with a tripping current of not more
than 30mA protected supply. Use of an RCD reduces the risk of
electric shock.
To prevent dust irritation, the wearing of a face mask is
recommended.
Check thoroughly the area you are going to work on and remove
all items that can be sucked into the suction tube or blown away
by the air blower.
Do not begin working without air tubes, safety devices and
covers installed in place.
ELECTRIC BLOWER SAFETY WARNINGS
IBL EB 60-69

7
PRODUCT OVERVIEW
1. Nozzle
2. Blast Port
3. Trigger Switch
4. Variable Speed Knob
5. Lock-On Button
6. Suction Port
7. Dust Bag
IBL EB 60-69

8
Rated voltage
Rated Input Power
Rated no load speed
Weight
Blow rate
Protection class
On the product or on the packing box, the rating label and within
these instructions you will find among others the following symbols
and abbreviations. Familiarize yourself with them to reduce hazards
like personal injuries and damage to property.
: 230V~50Hz
: 600W
: 6000-14000 rpm
: 1.36 Kg
: 3.3 m3/min
: Class II
IBL EB 60-69
PRODUCT SPECIFICATIONS
SYMBOLS
Caution / Warning
Wear protective gloves
This product is of protection class II. That means it is
equipped with enhanced or double insulation
Wear hearing and eye protection
Wear dust mask

9
Unpack all parts and lay them on flat, stable surface. Remove all
packing materials. Make sure the delivery contents are complete
and free of any damage. If you find that parts are missing or
show damage, do not use the product but contact your dealer.
Using an incomplete or damaged product represents a hazard to
people and property.
Ensure that you have all the accessories and tools needed for
assembly and operation. This also includes suitable personal
protective equipment.
The Electric blower is a dual function device designed for blowing
and sucking in the around the garage, shop or home. It can be
used to remove small debris, dust, shavings, leaves, or blow dry
water on a smooth surface. Not recommended for rough, porous
or uneven surfaces. This device is not designed for industrial
applications. The device cannot be used for other purposes
than its intended use.
For safety reasons it is essential to read the entire instruction
manual before first operation and to observe all the instructions
mentioned in it.
SETUP
UNPACKING AND ENSURING
WARNING! The product must be fully assembled before
operation! Do not use a product that is only partly assembled or
assembled with damaged parts! Follow the assembly instructions
step-by-step and use the pictures provided as a visual guide to easily
assemble the product! Do not connect the product to power supply
before it is completely assembled!
INTENDED USE
IBL EB 60-69
Tabla de contenidos

















