Hypertherm PMX1000 Manual de referencia

PMX1000 & PMX1250

RCD Resistor Replacement

Field Service Bulletin

804950 – Revision 2 – July, 2017

Hypertherm Inc.

Etna Road, P.O. Box 5010

Hanover, NH 03755 USA

603-643-3441 Tel 603-643-5352 Fax

www.hypertherm.com

RCD RESISTOR REPLACEMENT

Field Service Bulletin 1

Introduction

Purpose

Describes necessary steps to replace the RCD resistors (R119 and R120) on the power board of the PMX1000 and

PMX1250.

Note: This upgrade only applies to power supplies with serial numbers prior to:

PMX1000 – 1000-013717

PMX1250 – 1250-007888

Tools Needed

Phillips head screwdriver

Wire cutters

Kit Contents

Item Part Number Description Qty

1 109529 24K 13W resistor 2

WARNING

ELECTRIC SHOCK CAN KILL

Disconnect electrical power before performing any maintenance.

All work requiring removal of the power supply cover must be performed by a

qualified technician.

See Section 1 of the Operator Manual for more safety precautions.

RCD RESISTOR REPLACEMENT

Field Service Bulletin 2

Replace damaged resistors

1. Disconnect power and remove cover from power supply.

2. Discharge capacitors C94 and C98. See photo below.

3. Use wire cutters to remove resistors R119 and R120.

Note: cut leads next to the surface of the power board.

WARNING

ELECTRIC SHOCK CAN KILL

Use a multi-meter in VDC mode to discharge the capacitors to

less than 10VDC before removing the mounting screws.

Cut 4 places as shown

C98

C94

C98

C94

4. Remove screws from capacitors C94 and C98 as show.

R119

R120

Resistor (2)

Field Service Bulletin 3

Correct Installation

5. Install new resistors on capacitors C94 and C98 as shown. Tighten screws to 20 inch pounds (24 kg cm).

Note: Align bleeder hole on capacitor with view hole on power board.

6. Install power supply cover.

Bleeder hole

View hole (2)

Torque screws (4) to

20 inch pounds (24 kg cm)

CAUTION: Cross-threading the screws may cause

the capacitors to fail.

Note: assemble in the following order.

PCB, resistor, large terminal, small terminal, screw

C94

C98

Hypertherm and Powermax are trademarks of Hypertherm Inc.

and may be registered in the United States and/or other countries.

RCD RESISTOR REPLACEMENT

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortador de Hypertherm

Hypertherm

Hypertherm HyPerformance Plasma HPR260 Manual de usuario

Hypertherm

Hypertherm ArcGlide Torch Height Control Manual de usuario

Hypertherm

Hypertherm HyDefinition HD4070 Manual de usuario

Hypertherm

Hypertherm Powermax30 AIR Manual de usuario

Hypertherm

Hypertherm HyDefinition HD3070 Manual de usuario

Hypertherm

Hypertherm MAX200 Manual de usuario

Hypertherm

Hypertherm HT4001 Manual de usuario

Hypertherm

Hypertherm HyPerformance HPR400XD Manual de usuario

Hypertherm

Hypertherm HT4400 Manual de usuario

Hypertherm

Hypertherm powermax 190c Manual de usuario

Hypertherm

Hypertherm HD4070 PC-104 Manual de referencia

Hypertherm

Hypertherm Powermax30 AIR Manual de usuario

Hypertherm

Hypertherm HyPerformance Plasma HPR800XD Manual de usuario

Hypertherm

Hypertherm MAX200 Manual de usuario

Hypertherm

Hypertherm HyPerformance HPR400XD Manual de usuario

Hypertherm

Hypertherm Command THC Manual de usuario

Hypertherm

Hypertherm POWERMAX 800 Manual de usuario

Hypertherm

Hypertherm Powermax45 XP Manual de usuario

Hypertherm

Hypertherm HyPerformance Plasma HPR400 Manual de usuario

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario