hydrotab BT Series Manual de usuario
Hydro
Tab
Marine Engineering
Hydrotab BT Series
Hydrotab BT installation & Moby Automatic controller
NMEA 2000
NMEA 0183
Hydro
Tab
Marine Engineering
2
Hydro
Tab
Marine Engineering
Disclaimer
The interceptor units are also steering
equipment and it is the sole responsibility of
the navigator-operator to ensure that, at any
point, any problem that will alter the boat's
course, rising from malfunction of
interceptors, should be dealt immediately by
the operator. At no circumstances, fault of our
interceptor equipment leading to any kind of
accident, creates liability for the
manufacturer.
Trademark Notice
Hydrotab is a registered trademark of Olympic
Engineering Ltd, Greece. All other trademarks,
trade names or company names referenced
herein are used for identification only and are
property of their respective owners.
Patent Notice
The Hydrotab products are protected by
patents and industrial design patents, patents
pending or design patents pending.
Declaration of conformity
This product conforms to the following
Electromagnetic Compatibility (EMC)
regulations and standards for use in marine
environments.
CE EN 60945
Technical information and
Documentation
The technical information provided in this
document was accurate and correct at the
corresponding production time of the
Hydrotab interceptors. Our operating principal
for improving the manufactured product, may
lead to changes regarding its specifications
without prior notice. Liability will not be
accepted for any inaccuracy considering the
product and the user manual.
Fair use statement
This manual can be printed or copied for your
own use only. Copies should not be provided
to third parties and manual should not be
commercialized.
Product Disposal
Waste removal of this product must be
according to the Waste Electrical and
Electronic Equipment (WEEE) Directive.
Product Registration
Please register your product online in order
the warranty to be valid.
3
Hydro
Tab
Marine Engineering
Table of Contents
Disclaimer
2
Installation Kit
4
Required Tools for Installation
5
Before Installation
5
Safety precautions
5
Proper Interceptor Installation in Transom
6
Interceptor Installation
7
BT Series Interceptor and Anode Mounting and Coating Instructions
13
Interceptor Installation (Indirect Air Supply)
14
Air Unit Installation
14
Air Unit Fuse Replacement
15
Moby Controller Installation
16
Air Unit: Direct Installation Diagram
17
Air Unit: Installation diagram on existing NMEA Network
17
Double Speed Air Unit: Direct Installation Diagram
18
Double Speed Air Unit: Installation diagram on existing NMEA Network
18
Single Air Unit Electrical Diagram
19
Single Air Unit Pneumatic Diagram
19
Double Speed Air Unit Electrical Diagram
20
Double Speed Air Unit Pneumatic Diagram
20
Spare Parts List - Model: 160BT (ASM-00928)
21
Spare Parts List - Model: 320BT (ASM-00560)
22
Spare Parts List - Model: 480BT (ASM-00561)
23
Spare Parts List - Model: 640BT (ASM-00562)
24
Spare Parts List - Model: 800BT (ASM-00563)
25
Spare Parts List - Model: 960BT (ASM-00564)
26
Spare Parts List - Model: 1500BT (ASM-00940)
27
Spare Parts List - Model: 2000BT (ASM-00941)
28
Spare Parts List - Air Unit (ASM-01065)
29
Spare Parts List - Double Speed Air Unit (ASM-01174)
30
Moby Troubleshooting
31
Warranty Conditions
32
4
Hydro
Tab
Marine Engineering
Installation Kit
1. Two interceptors
6. Pipe 8mm
Use drill Ø5.5mm x 9 holes
Χρησιμοποιήστε τρυπάνι Ø5.5mm x 9 τρύπες
Lower edge of the hull
Άκρη γάστρας
Άνω
μέρος
Άνω
μέρος
MOD: 480BT
Use drill Ø8.5mm
Χρησιμοποιήστε τρυπάνι Ø8.5mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø5.5mm x 9 holes
Χρησιμοποιήστε τρυπάνι Ø5.5mm x 9 τρύπες
Lower edge of the hull
Άκρη γάστρας
Άνω
μέρος
Άνω
μέρος
MOD: 480BT
Use drill Ø8.5mm
Χρησιμοποιήστε τρυπάνι Ø8.5mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
4. Cables
2. Two interceptor drilling patterns
8. Screws
Air Unit wall mounting screws (4,8x25)
Fitting mounting screws (4,8x25)
Interceptor mounting screws (6,3x32)
3m-supply cable - Female
+
-
3m Male-Female
10m Female-Female
Inline terminator
3m Male-Female
12V or 24V 24V only
5. Moby Controller
MenuAuto
7. Moby Controller Drilling Pattern
Use drill Ø10mm
Χρησιμοποιήστε
τρυπάνι Ø10mm
MOBY CONTROLLER DRILLING PATTERN
Cut here
Κόψτε εδώ
114 mm
88 mm
Άνω
μέρος
Use drill Ø10mm
Χρησιμοποιήστε
τρυπάνι Ø10mm
Use drill Ø10mm
Χρησιμοποιήστε
τρυπάνι Ø10mm
Use drill Ø10mm
Χρησιμοποιήστε
τρυπάνι Ø10mm
9. Fittings
Indirect air supply pipe holder mounting
screws (3,5x13)
3. One Hydrotab AIR unit 12 OR 24VDC
5
Hydro
Tab
Marine Engineering
A good hint is that the closer the units are to the water line, the best the bank control of the boat will be
(Figure 3).
Attention! Please make sure that the pipe
insertion hole is accessible from the engine room
(Figure 2).
Make sure there are no obstructions behind the
drilling area (tanks, fuel lines, cabling) which can
be damaged or prevent the installation (Figure 1).
1. For high speed boats, overtrim may cause unexpectable turn. Improper use of trim tabs, may result to
accident or injury.
2. DO NOT PLACE YOUR FINGERS INSIDE THE INTERCEPTOR, through the front holes (Figure 4).
Severe injury danger!!!
Before Installation
21
3Right
Wrong
Drill Ø4 Drill Ø8,5
Drill Ø5.5 Hole Saw Ø70
Drill Ø3
5mm
Allen Key No 5Screwdriver Drilling tool
Marking tool
(pencil or marker)
Sikaflex gun
Safety precautions
WARNING!
4
Required Tools for Installation
If there is a double installation on the boat please
allow a 18 to 20 mm space between them (Figure
4).
6
Hydro
Tab
Marine Engineering
Right
Transom
Interceptor
Proper interceptor installation in transom
For maximum performance and less drag, install interceptors on the transom so blades deploy vertically.
If transom is not vertical to water plane, correct the angle by using wedges or other means.
Transom
Interceptor
Wrong
If the boat's transom has a significant curvature, it is necessary to create a flat plane for the installation
(acceptable flatness tolerance: 2mm).
Optimal
Less performance Correct angle
More drag
wedge
For aluminum hulls, it is suggested Isolation Plates between hull and interceptors to be installed. You can
find installation instructions in the Isolation Plates Kit.
7
Hydro
Tab
Marine Engineering
Interceptor Installation
5
Tape
Remove the pattern and drill according
the pattern indications
Drill all the pattern holes with a 3mm bore
without removing the pattern
6
You will need
No 4 No 8,5
No 5,5
8
Hydro
Tab
Marine Engineering
Allen 5mm
Interceptor Installation
8
Use a spatula to clean the excessive
glue from the holes
9
7
Use the special pipe
included in the packaging
M6,3xL*
Optional: Connecting Interceptors with Earthing Grid of boat
Except periodical replacement of anodes, you can enhance protection of interceptors from electrolytic corrosion by connecting
them to the earthing grid of the boat:
1. Drill through the hull one of the mounting pattern-holes on the transom.
2. Replace one regular self-tapping mounting screw (M6,3x32), with a longer screw (Inox 316, Φ6.3mm) so to run through the
transom wall (use sealant before tightening the screw).
3. Connect the screw with earthing grid of boat.
*Use inox 316 screw M6.3 of appropriate length
to run through the transom (not included in the set)
Apply sealant Sikaflex 291 to the holes
9
Hydro
Tab
Marine Engineering
Interceptor Installation
10
11
Direct air supply Optional:
Indirect Air Supply Kit
10
Hydro
Tab
Marine Engineering
Interceptor Installation
13
12
Este manual sirve para los siguientes modelos
18
Tabla de contenidos
Otros manuales de Equipos marinos de hydrotab
Manuales populares de Equipos marinos de otras marcas
Clarion
Clarion GR10BT Manual de reparación
Raymarine
Raymarine Maxiview ST80 Guía del usuario
GUIDANCE MARINE
GUIDANCE MARINE 20- Series Instrucciones de montaje
Raymarine
Raymarine ST60 Tridata Guía del usuario
olympia electronics
olympia electronics ΒS-531/1/MAR Manual de usuario
Sonic
Sonic 2024 Manual de usuario