Hyco Ara IN30T Hoja de especificaciones
Product Instruction Manual
Ara
Instantaneous Inline Water Heater
IN30T
v20.8.1
Overview
Thank you for purchasing an Ara Instantaneous Water Heater. Instantaneous water heaters
are very energy ecient as they only consume energy when they are in use, so have no
standing losses. The IN30T is intended for light hand washing at a single basin and must be
used with a spray head tap.
Key Features
• Hot water for light handwashing at a single basin only
• Bare wire heating system gives fast heat up time
• Heats the water instantly as it ows through the unit
• Energy ecient – no standing heat losses
• Compact space saving design
• External electronic thermostatic control accurate to the nearest degree
• LED temperature display
• Energy saving – only uses the power required to deliver the chosen temperature
• Not suitable for use with thermostatic mixing valves or taps or to supply a mixer tap
The appliance must only be connected to a single phase supply.
Isolate electrical and water supply before installation.
Electrical installation must be carried out by a qualied electrician in accordance
with the latest edition of the IEE wiring regulations.
Only connect the appliance to a power supply that conforms to the specication
stated on rating plate.
The appliance must be earthed at all times.
The appliance must be permanently connected to the electrical supply through
an isolating switch with a contact separation of no less than 3mm in all poles.
Important Safety Points
Please fully read these instructions before commencing installation and follow to ensure
that installation and operation are simple and safe.
2
Do not use the appliance if there is any possibility of the water supply being frozen.
Never remove the cover of the appliance without rst isolating it from the electrical
power supply.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
The supply cord cannot be replaced by the user. If the supply cord is damaged the
appliance should be returned to the manufacturer or an authorised service agent
for replacement.
3
1. Installation
4
Choosing Heater Location
• Consider the risks and consequences posed by any potential leak from the product or
supply pipework in the future. Avoid installation in areas where the consequences of
a leak could be unusually severe e.g. above computer equipment
• Consider the potential for the pipework or heater freezing and take preventative
action if required e.g. pipe lagging.
• It is advised that the heater be located as close as practical to the hot water outlet in
order to avoid unnecessary heat losses through the pipework and improve delivery
performance.
This heater should not be installed in a location where the risk of freezing cannot
be managed.
The heater is not suitable for use with thermostatic mixing valves or taps or to
supply a mixer tap.
Removing and Mounting the Bracket
• Use a at headed screwdriver or similar, place it into the lug on the bracket (between
the inlet/outlet connections, see diagram 1) and then gently lever the bracket away
from the heater.
• To remove the bracket fully from the unit pull down at the bottom of the bracket.
• When retting the unit to the bracket reverse the process.
• Before attaching the bracket to the wall, consider the wiring route to the heater. The
bracket on the heater has an additional knock out section to allow the wire to exit
from either the left, right or top of the bracket depending on wiring requirement.
Always ensure there are no hidden cables or pipes before commencement of
drilling.
5
Diagram 1
• The unit can be installed with the inlet and outlet at the top or at the bottom. Ensure
the bracket orientation corresponds with the unit. When installed with the inlet and
outlet at the bottom of the heater the electronic temperature display will rotate
automatically.
• Mark and drill two holes using the bracket as a template. Use the supplied wall plugs
and screws to attach the bracket to the wall (see Diagram 1).
• Ret the unit to the bracket to complete mounting.
Cable defaults out of the right hand side when viewed from the front and installed with the inlet/
outlet at the top of the unit. Supplied pre knocked out but can be changed if desired.
2. Plumbing Connection
Flush supply pipes to remove any debris before connecting the heater to the water
supply.
This unit is intended to be permanently connected to the mains water supply and
should not be connected by a detachable hose-set.
The water resistivity must not be less than 1300 Ωcm @15 C.
• The maximum water supply temperature for this heater should not exceed 30°C.
• Using the supplied washer with gauze, make a connection from the incoming
cold-water supply to the inlet side of the heater (blue collar). It is recommended a
service valve (not supplied) is tted on the incoming supply to facilitate any future
maintenance.
• Make a connection from the outlet side of the heater (red collar) to the hot water tap.
• The supplied 1.6 l/min (litres per minute) ow restrictor must be tted to the hot
water tap (compatible hot water tap required).
• Turn on the cold water supply and open the hot water tap. Allow the water to ow for
several minutes to purge all air from the heater. This step is required every time the
heater has been drained for any reason, such as routine maintenance.
• Close the hot water tap and check all connections are watertight under pressure.
6
3. Electrical Connection
Before switching on power to the unit the system must be full of water and tested
for leaks.
Electrical installation must be carried out by a qualied electrician in accordance
with the latest edition of the IEE wiring regulations.
The heater must be earthed.
Isolate electric and water supply before electrical installation.
Ensure all wiring provisions meet the specications of the heater as stated on the
rating label and ‘Specication’ section of this manual.
• Make connection to the electrical supply from the heater via an appropriately rated
fused spur using the cable supplied.
• Connection should be made as follows:
Green/Yellow earth wire to the terminal marked “ E” or
Brown/Red live wire to the terminal marked “L”
Blue/Black neutral wire to the terminal marked “N”
Diagram 2
7
4. Operation
Before switching on power to the unit the system must be full of water and tested
for leaks.
This water heater is for low ow hand washing at a single basin only.
Instantaneous heaters only heat water as it passes through the tank. Because the
maximum power of the heater is xed there is a limit to the rate at which hot water
can be delivered.
• Turn on the heater using the on/ o touch screen (see diagram 3). It will automatically
begin heating when it detects a ow of water through it.
• On rst installation the heater requires an initial 12 seconds (approx) of continuous
water ow through the unit to start heating.
• When the water ow is turned on using the outlet/ tap, the heater will display the
current water temperature. The electronic temperature display will only operate
whilst water is owing through the heater.
• Whilst water is owing through the heater, the target temperature can be adjusted
using the left / right hand touch screen adjustments. After a second or two the heater
will go back to displaying the current water temperature and the new setting is
stored.
8
Diagram 3
• Once the target temperature is set the heater will aim to reach it and will never
exceed it.
• The heating performance of the heater is based on ow rates, the slower the ow
the higher the temperature uplift. The delivered temperature is the incoming water
temperature plus the temperature uplift (ow dependent).
• A ow restrictor is supplied with this heater which, when tted into the nozzle of a
tap will ensure a steady ow rate of 1.6 l/min is maintained. With this a temperature
uplift of 27°C is achieved.
• The incoming water temperature can uctuate dependent on time of year in the UK.
Winter may result in incoming temperatures below 10°C, whereas summer water
temperatures can be upwards of 15°C. It is imperative this is taken into account.
• For example the heater could deliver 42°C water in the summer (with an incoming
water supply temperature of 15°C). The same product with the same ow rate would
only be able to deliver 37°C in winter (due to a lower incoming water temperature
of 10°C). The delivered temperature will be even lower if the incoming water supply
temperature is less than 10°C.
• If there is a power interruption the heater will recall the last selected temperature.
When power is restored the heater must be turned back on using the bottom on/
o touch screen. Following this, it will again require 12 seconds (approximately) of
continuous water ow through the unit to start heating.
9
• Press down on the ribbed area of the cover and move towards the wall.
• Apply pressure to the rear of the cover until the front lifts.
• Remove the cover by pulling it forwards.
• Adjust the screw to the desired setting. Turn anticlockwise for maximum water ow.
Turn clockwise to reduce the water ow.
Adjusting Water Flow Rate
Diagram 4
A ow restrictor is supplied and must be tted to the outlet/tap attached to this heater.
This is the best way to control the performance of this product and so adjustment of
the ow rate should not be necessary except in areas with notably high incoming water
pressures.
10
Tabla de contenidos
Otros manuales de Calentador de agua de Hyco
Hyco
Hyco Rho IN44 Hoja de especificaciones
Hyco
Hyco Aquila Hoja de especificaciones
Hyco
Hyco powerflow series Manual de usuario
Hyco
Hyco SF05K Hoja de especificaciones
Hyco
Hyco SF05K Manual de usuario
Hyco
Hyco Microboil Smart MS3W Hoja de especificaciones
Hyco
Hyco MBS6 Manual de usuario
Hyco
Hyco Handyflow HF05L Manual de usuario
Hyco
Hyco Rho Manual de usuario
Hyco
Hyco RHO IN44T Manual de usuario
Hyco
Hyco Handyflow HF05LQ Manual de usuario
Hyco
Hyco Speedflow SF10SS Hoja de especificaciones
Hyco
Hyco Rho IN44 Hoja de especificaciones
Hyco
Hyco ULTRAWASH 3.0kW Guía
Hyco
Hyco IN88 Manual de usuario
Hyco
Hyco SpeedFlow sf10l Manual
Hyco
Hyco HF05LM Hoja de especificaciones
Hyco
Hyco Aquila IN96T Hoja de especificaciones
Hyco
Hyco AP25LM Guía
Hyco
Hyco HF05VC Manual de usuario
