Hyco Aquila Hoja de especificaciones

Product Instruction Manual

Aquila

Instantaneous Inline Water Heater

IN96T

v23.10.9

Overview

Thank you for purchasing an Aquila Instantaneous Inline Water Heater. This 9.6 kW

appliance is to be used for hand washing at up to 2 basins, or for a single light shower, or

light dish washing. Instantaneous water heaters are energy ecient as they only consume

energy when in use, so have no standing losses. The IN96T is mains pressure with external

electronic temperature control. Bare wire heating systems oer rapid heat up times and a

near instant supply of hot water.

Conrm that the ow rate and temperature performance is adequate for your application

using the tables provided. This appliance is not suitable for use with thermostatic mixing

valves or taps or to supply a single lever mixer tap.

Please read and follow these instructions to ensure that installation and operation are as

simple and safe as possible.

Important Safety Points

This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

The appliance should only be installed and maintained by a competent person in

accordance with any local electrical and plumbing regulations.

The appliance must be permanently connected to the electrical supply through an

appropriately rated isolating switch with a separation in all poles.

Only connect the appliance to an electrical supply that meets the specication

detailed on the rating label.

The appliance must be earthed.

Only connect this appliance to a water supply that meets the min/ max pressures

specied in the specications section of this manual.

This appliance is intended to be permanently connected to the water mains and

should not be connected by a detachable hose-set.

The resistivity of the water supply must not be less than 1300 Ωcm.

This appliance should not be installed in a location where freezing can occur.

This appliance is not designed for outdoor use or use in damp environments.

Do not use a supply with incoming water temperatures greater than 60˚C.

1. Installation

Do not locate the appliance where the consequences of a water leak could be

unusually serious.

This appliance should not be installed in a location where freezing can occur.

This appliance is not designed for outdoor use or use in damp environments.

• When choosing a location for the appliance, consider the visibility of any leak that

might arise. This is particularly important when locating in a concealed area such as a

cupboard.

• The appliance must be mounted horizontally with the inlet and outlet connections at

the bottom of the appliance (see diagram 1).

Wall Mounting

Diagram 1

• Before attaching the appliance to the wall, consider the wiring route to the appliance.

The electrical cable can enter through the opening in the back for concealed cabling.

Knock out panels in the top right hand corner of the back plate and front cover are

available for side entry.

Ensure there are no hidden cables or pipes before commencement of drilling.

• Remove the front cover from the appliance by means of the single screw located

between the inlet and outlet ttings. The cover will lift rst from the bottom and then

unhook from the top. Carefully release the PCB lead from the main unit to completely

uncouple the cover.

• It is advised that the appliance be located as close as practical to the hot water outlet

in order to avoid unnecessary heat losses through the pipework.

• Once the preferred location has been decided, oer the appliance to the wall. Ensure

the appliance is level and mark the hole locations onto the nal mounting surface

(see diagram 1).

• Take the appliance away from the mounting surface and drill the holes marked from

the previous step.

• Insert wall plugs and oer the appliance back up to the mounting surface. Locate the

screws through the unit and into the wall plugs and screw down securely.

2. Plumbing Connection

The resistivity of the water supply must not be less than 1300 Ωcm.

Do not use a supply with incoming water temperatures greater than 60˚C.

Only connect this appliance to a water supply that meets the min/ max pressures

specied in the specications section of this manual.

This appliance is intended to be permanently connected to the water mains and

should not be connected by a detachable hose-set.

• Ensure the following criteria are met for the water supply:

Minimum ow = 2.5 l/m

Pressure min/ max = 0.1 Mpa / 0.75 Mpa

Water resistivity = ≥1300 Ωcm

• Suitable for use with pre-heated water e.g. solar heating systems to a maximum of

60°C.

• Make the plumbing connections as indicated on the front cover of the appliance:

Inlet (cold mains)

Outlet (hot tap/ outlet)

• It is strongly recommended that a service valve be tted close to the appliance on the

cold feed, this will aid future maintenance.

• The inlet is the right hand pipe and the outlet the left, when viewed from the front.

• Turn on the cold mains feed and draw water through the appliance for several

minutes by opening the hot outlet. Ensure a smooth ow of water from the outlet

to conrm all air is purged from the system before closing the tap and carefully

inspecting all connections to ensure water tightness. This step is required every time

the appliance has been drained for any reason, such as routine maintenance.

Diagram 2

Flush supply pipes to remove any debris before connecting the appliance to the

water supply.

All pipework should be adequately earthed.

3. Electrical Connection

Do not commence electrical installation before connecting the appliance to the

water supply and verifying there are no leaks or air gaps.

The appliance must be permanently connected to the electrical supply through

an appropriately rated isolating switch with a separation in all poles.

Only connect the appliance to an electrical supply that meets the specication

detailed on the rating label.

The appliance must be earthed.

• Connection to the appliance terminal should be made as follows:

Earth cable to the terminal marked ‘E’

Neutral cable to the terminal marked ‘N’

Live cable to the terminal marked‘L’

Wiring Diagram

4. Operation

• Once installed and connected to the electrical supply the appliance is ready for use.

• Once turned on the appliance will automatically power up when it detects a ow of

water through it (min 2.5 l/m).

• Due to the nature of instantaneous heaters, water is only heated as it passes through

the tank. Because the maximum power of the appliance is xed there is a limit to the

rate at which hot water can delivered.

Controls

1 - Memory (record/ recall temp setting)

2 - Increase temperature setting

3 - Decrease temperature setting

4 - Power on/ o

Selecting a temperature

• Turn on the appliance using the power on/ o. On rst installation the temperature

setting will default to 38°C. To adjust the temperature press the up/ down buttons

until the desired target temperature is displayed.

• To store a frequently used temperature setting, press and hold the“M”button. This

stores the current temperature and allows it to be recalled at any time by pressing the

“M” button.

Setting the maximum ow rate

• The ow rate is shown on the front display of the appliance in L/ MIN. If the desired

temperature cannot be met at the current ow rate the temperature display will ash

to indicate this. Adjust the ow down using the dial on the front of the appliance until

the temperature display stops ashing.

• Incoming water temperatures can vary depending on the time of year. For this reason

the maximum ow rate may need adjusting down in order to maintain a suitable

temperature during colder periods.

• The appliance has memory recall, it will revert to its previous operational state

following a power interruption.

• Once the desired temperature is selected the

appliance will manage the power in order to

ensure the temperature is not exceeded. The

current power usage is displayed by the lines at

the bottom of the display.

5. Cleaning and Maintenance

Never remove the cover of the appliance without rst isolating from the electrical

power supply.

The appliance should only be installed and maintained by a competent person in

accordance with any local electrical and plumbing regulations.

Do not use abrasive chemicals or cloths to clean this appliance.

Isolate the appliance from the electrical and plumbing supply before performing

any maintenance task.

The appliance should be drained if it will be switched o or unattended for

any length of time, particularly during the colder months of the year where the

possibility of freezing temperatures exists.

Ensure any future maintenance or modications to the plumbing system also

complies with the guidelines in these instructions.

Keep records of maintenance and ensure any future occupier of the building is

fully aware of the content of these instructions.

• Visually inspect the appliance and its immediate surroundings regularly for any signs

of water escape that might indicate the product may be nearing the end of its natural

life.

• Use a soft damp cloth when cleaning, avoid excessive use of liquids.

• Check outlet of any tap connected to the heater at regular intervals and remove any

build up of scale that might obstruct the ow rate of water through the appliance.

Overheat Protection

• In the unlikely event of a malfunction, the appliance is tted with a manual reset

thermal cutout. This is located under the cover near the top of the heating chamber.

To reset press the push button located in the centre of the device.

• Once reset, operate the appliance and ensure there is no underlying fault which is

causing the water to overheat.

7. Specication

Model IN96T

Power 9.6 kW

Voltage 230 V

Rated current 42 A

Frequency 50 Hz

Min operating ow rate 2.5 l/m

Min working pressure 0.1 MPa (1 bar)

Max working pressure 0.75 MPa (7.5 bar)

Max incoming water supply temperature 60 °C

Required water restivity ≥1300 Ωcm

Water connection inlet/ outlet 1/2” BSP

IP rating IPX4

Thermal cutout temperature 75 °C +/- 5

Dimensions (h x w x d) 140 x 190 x 80 mm

Weight empty 2.0 kg

Approvals CE, UKCA, WRAS

6. Temperature Performance

Temperature/ Flow Rate

Maximum temperature increase from ambient incoming water supply temperature at a

ow rate of:

Flow rate (l/m) IN96T

2.5 55°C

3.0 45°C

4.0 34°C

5.0 27°C

Examples

Maximum water temperature

Incoming water temperature Flow rate IN96T

13 °C - Winter 4.0 l/m 47°C

17 °C - Summer 4.0 l/m 51°C

Table 1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de agua de Hyco

Hyco

Hyco HF05VC Manual de usuario

Hyco

Hyco SF05K Hoja de especificaciones

Hyco

Hyco AP25LM Guía

Hyco

Hyco ULTRAWASH 3.0kW Guía

Hyco

Hyco Handyflow HF10VC Manual de usuario

Hyco

Hyco Microboil Smart MS3W Hoja de especificaciones

Hyco

Hyco HF05LQ Manual de usuario

Hyco

Hyco Superflow SR90 Hoja de especificaciones

Hyco

Hyco Powerflow Manual de usuario

Hyco

Hyco SF05K Hoja de especificaciones

Hyco

Hyco Rho Manual de usuario

Hyco

Hyco Aquila IN96T Hoja de especificaciones

Hyco

Hyco powerflow series Hoja de especificaciones

Hyco

Hyco Handyflow Undersink HF05MVC Manual de usuario

Hyco

Hyco Handyflow HF05L Manual de usuario

Hyco

Hyco Speedflow SF10L Manual de usuario

Hyco

Hyco HF05LM Hoja de especificaciones

Hyco

Hyco Speedflow SF10SS Hoja de especificaciones

Hyco

Hyco SpeedFlow sf10l Manual

Hyco

Hyco Ara IN30T Hoja de especificaciones

Hyco

Hyco Rho IN44 Hoja de especificaciones

Hyco

Hyco MBS6 Manual de usuario

Hyco

Hyco Rho IN44 Hoja de especificaciones

Hyco

Hyco SF05K Manual de usuario

Manuales populares de Calentador de agua de otras marcas

Kenmore

Kenmore 153.582400 Manual de usuario

Applimo

Applimo Edel AIR Manual de usuario

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manual de usuario

clage

clage E-Mini Series Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-180 Manual de usuario

Bradford White

Bradford White EF Series Manual de usuario

Eccotemp

Eccotemp 40-H Manual de usuario

Dimplex

Dimplex ECSd125-580 Guía

Dux

Dux 32FCR6N Manual de usuario

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guía de solución de problemas

Noritz

Noritz N-132M Manual de instrucciones

TESY

TESY GCV7/4S 10047 Hoja de especificaciones

A.O. Smith

A.O. Smith Gphe 50 Manual de usuario

Koryo

Koryo KWHZF15Y Manual de usuario

Pentair

Pentair PSC-14-4-02 Manual de usuario

GE 40M06AAG Instrucciones de montaje

Thermor

Thermor AEROMAX SPLIT 2 Manual de usuario

American Hometec

American Hometec AHQ-B03X Manual de usuario