Hussmann D5X-E Manual de usuario
All equipment should be thoroughly examined for
shipping damage before and during unloading.
This equipment has been carefully inspected at our
factory. Any claim for loss or damage must be made
to the carrier. The carrier will provide any necessary
inspection reports and/or claim forms.
Every effort is made to ship all parts for the kit. The
Hussmann Service Center can be reached by calling
• from U.S. & Canada 1-800-922-1919 •
• from Mexico 1-800-522-1900 •
Glass View End for
Multi-Deck Dairy
Merchandisers
Field Installation
PARTS LIST
Item Quantity Description
D5X-LE D5X-E
1. 2 2 Nut Retainer 5/16 -18 (left end only)
2. 1 1 Gasket Tape 1/2x 15/8x 180
3. 1 1 Gasket Tape 1 x 1/2 x 180
4. 1 1 Silicone Sealer
5 1 1 Bottom End Assembly
6. 2 2 Cap Screw 5/16 -18 x 21/2
7. 4 4 Flat Washer 5/16
8 1 1 Top End Assembly
9. 2 2 Cap Screw 5/16 -18 x 13/4
10. 1 1 Multiglass Assembly
11. 1 1 Multiglass Extrusion
12. 6 6 Screw – SM Hex Head – TEK2 – #8-18 x 1/2
13. 1 1 Fascia End Plate
14. 1 1 Bumper End Plate (PART OF END BUMPER KIT)
15. 1 1 Fascia Panel
16. 2 2 Bracket — End Splashguard
17. 1 1 End Splashguard Cover
18. 1 1 Splashguard — Standard 5.75 End
19. 4 4 Screw – Truss Head – Phillips – #8-18 x 1/2 – Black
20. 1 1 Corner Bumper (PART OF END BUMPER KIT)
21. 1 1 End Bumper (PART OF END BUMPER KIT)
1
P/N 0503025_A
January 2008
©2008 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
U.S. & CANADA 1-800-922-1919 • MEXICO 1-800-522-1900 • WWW.HUSSMANN.COM
D5X-LE D5X-E
INSTALLING END ASSEMBLIES
End assemblies are normally factory
installed. The following information
is provided for retrofit or field instal-
lation.
1Uncrate
Place glass crate on flat surface
with braces down as shown in
Figure 1, Detail A. Remove
screws from top.
Lift off top as shown in Detail B
of Figure 1.
Remove cardboard packaging
as shown in Detail C of Figure 1
and inspect Glass and Extrusion
for damage.
Carefully unpack crate with end
assemblies. Check for damage.
Locate and identify the parts
listed on Page 1.
Figure 1 — Uncrate and Inspect Glass
P/N 0503025_A
2U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Detail A
Detail C
Detail B
2Preparation
Left End Only
Install Nut Retainers – 1 in
canopy positions indicated in
Figure 2.
Remove any other nut retainers
and alignment pins from End
Frame.
Right End Only.
Remove any factory-installed
alignment pins.
Verify Nut Retainers are in
canopy positions indicated in
Figure 2. Remove all others.
Glass View End for Multi-Deck Dairy Merchandisers P/N 0503025_A
3
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 2 — Install Nut Retainers in End Canopy
3Apply Gasket
Apply Gasket – 2 and
Gasket – 3 as indicated in
Figure 3.
The same gasket arrangement is
used on either end.
Assure good adhesion of gaskets
by wiping the end frame with
rubbing alcohol to remove accu-
mulated dust and oils.
First Gasket
1 in. Gasket
(24 mm)
Second
Gasket
15/8in. (41 mm)
Figure 3 — Apply Gaskets
P/N 0503025_A
4U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
4Align
Bottom End Assembly – 5
with end frame. Working from
inside the case as shown in
Figure 4, insert Cap Screw – 6
through Flat Washer –- 7, then
through end frame and into end
assembly.
5Use Silicone Sealer – 4 to seal
end frame to end assembly as
shown in Figure 5.
Apply Silicone Sealer – 4
over both Cap Screws – 6
as shown in Detail 5A
Glass View End for Multi-Deck Dairy Merchandisers P/N 0503025_A
5
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 5 — Seal Bottom End Assembly
Figure 4 — Install Bottom End Assembly
Detail 5A
Silicone
Silicone
6Align Top End Assembly – 8
with end frame. Pins in the
assembly fit into the canopy end
frame as shown in Figure 6.
7Working from outside the case,
attach Top End Assembly – 7
to end frame with
Cap Screws – 9
as shown in Figure 7.
P/N 0503025_A
6U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Figure 6 — Align Top End Assembly
Figure 7 — Install Top End Assembly
Front
Front
Rear
8From the back, insert the
Multiglass Assembly – 10
between bottom and top end
assemblies. Refer to photos in
Figure 8. Push the multiglass
forward to butt against the front
corner trim.
This may require two people!
Glass View End for Multi-Deck Dairy Merchandisers P/N 0503025_A
7
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 8 — Install Multiglass Assembly
Insert Glass
from Rear
Use Even
Pressure
Keep Glass
Straight
Push Glass
Forward
Glass Stopped at
Front Corner Trim
9Attach the Glass Extrusion – 11
at the back of the multiglass
assembly using Screws – 12.
Refer to photos in Figure 9.
10 Attach the
Fascia End Plate – 13
at the back of the upper end
assembly using Screws – 12.
Refer to photo in Figure 10.
P/N 0503025_A
8U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Figure 9 — Install Glass Extrusion
Complete
Figure 10 — Install Fascia End Plate
Screw
Placement
in Fascia
End Plate
(PART OF END BUMPER KIT)
11 Attach the Bumper End
Plate – 14 at the back of the
upper end assembly using
Screws – 12. Refer to photo in
Figure 11.
Glass View End for Multi-Deck Dairy Merchandisers P/N 0503025_A
9
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 11 — Install Bumper End Plate
Screw
Placement
in Bumper
End Plate
12 Insert the top edge of the
Fascia Panel – 15 into the
top end assembly, slide upward
until the bottom edge clears the
lower track, then lower the
panel. No fasteners are used.
Refer to Figure 12.
Figure 12 — Install Fascia Panel
P/N 0503025_A
10 U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Otros manuales para D5X-E
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Comerciante de Hussmann
Hussmann
Hussmann IMPACT D5HR Manual de usuario
Hussmann
Hussmann MWG Manual de usuario
Hussmann
Hussmann IMPACT D5RRI Manual de usuario
Hussmann
Hussmann CIDM-I Instrucciones de funcionamiento
Hussmann
Hussmann Impact C1CWCEI Manual de instrucciones
Hussmann
Hussmann FMR Manual de usuario
Hussmann
Hussmann RI4-E Manual de instrucciones
Hussmann
Hussmann MWG Manual de usuario
Hussmann
Hussmann Impact Excel M3X-EP Manual de instrucciones
Hussmann
Hussmann Impact Excel M3X-GEP Manual de instrucciones
Hussmann
Hussmann VSG Instrucciones de funcionamiento
Hussmann
Hussmann D5X-LE Manual de instrucciones
Hussmann
Hussmann Impact C2-E Manual de usuario
Hussmann
Hussmann Excel FWG Manual de usuario
Hussmann
Hussmann DDS Manual de usuario
Hussmann
Hussmann D5NX-E Manual de instrucciones
Hussmann
Hussmann Impact Excel M4X-GE Manual de instrucciones
Hussmann
Hussmann IMPACT D5R Manual de usuario
Hussmann
Hussmann Freedom RFL Manual de usuario
Hussmann
Hussmann P2NX-E Manual de instrucciones
