Hunter Internet Thermostat Manual de usuario

OwnerÕs Manual

SINCE 1 8 8 6

44150

Other Quality Products from Hunter

Fans

HumidifiersAir Purifiers

We are pleased you have selected one of our broad line of home comfort products. Our

products are manufactured to high quality standards and are designed for years of service.

We hope you will be satisfied and thank you for buying a Hunter product.

Table Of Contents

Installation

Operation

Features 6

Remove Old Thermostat 8

Labeling Wires 10

System Selector Switches 14

Connecting Wires and Mounting Thermostat 14

Programming/Setting Clock 16

Personal Program Schedule 20

Reviewing Program Settings 24

Manual Overide 25

Filter Monitor 28

Temperature Span 29

Backlighting 29

Trouble Shooting Guide 30

Typical Wiring Diagrams 32

Read This Before Installing Thermostat

IMPORTANT

Read the entire installation section of this

Owner’s Manual thoroughly before you begin

to install or operate your Hunter Thermostat.

• Remove the mylar label from the display

window.

INSTALLATION

All installation is normally performed at your

thermostat.

PROGRAMMING

You can practice programming before

installing your thermostat by inserting and

connecting the batteries and following the

instructions on page 14. This can be done while

you relax in your favorite chair and is a very

good way to familiarize yourself with all the

functions of your Hunter Thermostat.

OPERATION

Your Hunter Thermostat is designed to

operate with most gas, oil, electric or 2-wire

hot water heating, and air conditioning systems

that have 24-volt or millivolt control.

This Hunter Thermostat will not control multi-

stage heating or cooling systems, 110/220 V

systems, or 3 wire zone systems.

COMPRESSOR PROTECTION

The thermostat provides a 4-minute delay

after shutting off the compressor before it

can be restarted. This feature will prevent

damage to your air conditioner compressor

caused by rapid cycling. It does not provide a

delay when there are power outages.

TEMPERATURE RANGE

Your thermostat can be programmed between

40°F and 95°F (5°C and 35°C). However, it will

display room temperatures from 32°F to 99°F (0°C

to 37°C).

POWER FAILURE

Whenever the main power is interrupted or

fails, the battery power retains the programs

and current time.

This thermostat is designed to optimize the use of your heating and cooling equipment. It

does this by matching your comfort (the temperatures in your home) to your schedule.

An example:

6 a.m. – You wake up. Program 1 has the heat set to 70° (21°C).

7:30 a.m. – You leave for work. The second program turns the heat back to 62°

(17°C) while you are away.

5 p.m. – You come home. The third program has already warmed your house

back to 70° (21°C).

10 p.m. – You go to bed. A half hour later, program 4 turns the heat back to 64°

(18°C) to save energy while you are under the blankets.

How This Thermostat Works…And Saves You Money

BATTERY WARNING

When the batteries are low, “LOW BATT”

indicator on the display will flash. When this

happens, install new batteries immediately.

Once the “LOW BATT” indicator appears, the

thermostat will continue to operate for

approximately 30 days. (Only alkaline batteries

should be used in your thermostat. Rechargeable

batteries have different properties which may

cause the thermostat to not operate properly.

Do not use old batteries.) The batteries should

last one year.

CAUTION: The batteries are the only source

of power used to operate your system. If you

do not replace the batteries, the display will

dim and your heating and cooling system will

stop operation.

NOTE: If you plan to be away from the

premises over 30 days, we recommend that

you replace the old batteries with new

alkaline batteries prior to leaving.

LIGHT

6-7

Features

Manual switch for

turning on heating and

cooling system.

Display backlight for viewing in the dark.

Manual switch for

automatic or continuous

fan operation.

Battery door for easy access

Soft touch programming

buttons (see below)

Display shows time, day, temperature, program number,

hold, usage and low battery indicator.

Reset button for

resetting computer back

to 12:00 A.M. and

clearing all programs.

Individual

pushbuttons for

raising or lowering

temperature settings.

M T W TH F SA SU

SET TEMP HOLD TEMP

88:88 88

HEAT COOL

1234

FILTER LO BAT

Changes the clock

into 12 or 24 hour

(military) mode.

For entering minute of day.

For revising

and changing

weekday or

weekend

programs

To reset filter

counter back

to zero. Returns

display to

current

time and

temperature.

Automatically

programs the

thermostat for

weekday and

weekend

program

settings.

For entering day of week.

Provides

permanent

temperature

setting by

overriding

stored

programs.

Also, clears

manual

override and

returns to

current

program

settings.

For entering hour

of day.

MIN

AUTO

PROGRAM

HOUR

PROG

DAY

HOLD

CLEAR

12/24 HRS RETURN

FILTER

RESET

This thermostat comes with two #8 slotted screws and two wall anchors for mounting. To

install your unit, you should have the following tools and materials.

■Slotted screwdriver ■Electric drill and 3/16" bit

■Hammer ■Two 1.5 V (AA) Size Alkaline batteries

CAUTION: Do not remove any wiring from existing thermostat before reading the

instructions carefully. Wires must be labeled prior to removal.

■IMPORTANT! Turn off the power to the furnace at the main power panel or at the furnace.

■Remove existing thermostat cover and thermostat. See Figure 1. Some thermostats will have

screws or other locking devices that must first be removed. Once wall mounting plate is

exposed, look for wires.

■If wires are not visible, they may be connected to the back of the wallplate. Again, look for

screws, tabs, etc. Some models have doors that open to expose wires and mounting screws.

(See Figure 1).

8-9

Installation

What You Need

Remove Old Thermostat

TYPICAL HOME THERMOSTATS

FIGURE 1

Wall Mounting Plate Thermostat Cover

■Each wire coming from the wall to the existing thermostat is connected to a terminal point on

that thermostat. Each of these terminal points is usually marked with a code letter as shown in

Table A on page 11.

■The number of wires in your system can be as few as two (for heat only systems), as many as

eight, or any number in between. If you follow the labeling procedures correctly, you do not

have to be concerned about how many wires there are.

■There is often no terminal marking on the existing thermostat of two wire, heat only systems.

Do not worry, just connect either of the wires to the RH terminal, then connect the other wire

to the W terminal to complete the circuit.

■IMPORTANT! BEFORE DISCONNECTING ANY WIRES, APPLY THE SELF-ADHESIVE

LABELS PROVIDED TO THE WIRE AS SHOWN IN TABLE A ON PAGE 11.(For example,

attach the label marked W to the wire which goes to the W or H terminal on your existing

thermostat.) IGNORE THE COLOR OF THE WIRES since

these do not always comply with the standard.

■After labeling wires, disconnect them from the existing

thermostat terminals.

■Remove existing wallplate. To make sure wires do not fall back

into wall opening, you may want to tape them to the wall.

■If hole in wall is larger than necessary for wires, seal this hole

so that no hot or cold air can enter the back of the

thermostat from the wall. This air could cause a false

thermostat reading.

10-11

Installation

Label Wires

WGYRH

Otros manuales para Internet Thermostat

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Hunter

Hunter

Hunter 40020A Manual de usuario

Hunter

Hunter F42213 Manual de usuario

Hunter

Hunter 42999 Manual de usuario

Hunter

Hunter 40135 Guía de configuración

Hunter

Hunter 44100 Manual de usuario

Hunter

Hunter 44132 Manual de usuario

Hunter

Hunter 42122 Manual de usuario

Hunter

Hunter 44860 Manual de usuario

Hunter

Hunter 42202 Manual de usuario

Hunter

Hunter 42999 Manual de usuario

Hunter

Hunter 44272 Instrucciones de montaje

Hunter

Hunter 44668 Manual de usuario

Hunter

Hunter Set & Save 47300A Manual de usuario

Hunter

Hunter 44550 Manual de usuario

Hunter

Hunter 40351 Manual de usuario

Hunter

Hunter SET & SAVE 47110A Manual de usuario

Hunter

Hunter 40135 Manual de usuario

Hunter

Hunter 44033-01 44272 Manual de usuario

Hunter

Hunter 44110 Manual de usuario

Hunter

Hunter 40120 Guía de configuración

Hunter

Hunter 44260 Manual de usuario

Hunter

Hunter 40020 Manual de usuario

Hunter

Hunter 44260 Manual de usuario

Hunter

Hunter 44050 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario