Hunter Internet Thermostat Manual de usuario

Internet Thermostat

Installation Guide

Getting Started

1. Power OFF Your HVAC System Unit

You will need a Phillips head screwdriver to complete this installation.

Read and save these instructions!

If you still need assistance after reading this manual, call our Technical Support at

USA: 1-888-830-1326 Canada: 1-866-268-1936

This thermostat is compatible with most 24V AC/millivolt systems with a maximum of 1 amp including: conventional oil,

gas, electric, hot water systems, single stage, and multi-stage heat pumps.This thermostat will not control line voltage

systems running 110V. Higher amp or line voltage systems will increase the risk of fire.

*This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*This device complies with RSS-GEN IC: Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

*Any alteration of this product, either intentional or unintentional, not expressly approved by the manufacturer could result in operation

failure of the device, inability to gain assistance from our technical team, or manufacturer refusing warranty support.

*This Class B digital apparatus complies with Canadian ICES-003.

Go to your circuit breaker panel and turn o

power to your compressor and furnace.

OFF

Turn Power

Tip: You may need a precision screwdriver (smaller tip) to detach wires from your old thermostat.

Alternatively, you may want to take a picture of the wires on your old thermostat for reference.

If you have any wire codes that do not match the Hunter labels, you may have a system that

does not conform to industry standard. Call our Technical Support at 1-888-830-1326.

Expose your existing thermostat wires.

Locate the wire terminals. If the wire terminals

are not visible, they may be connected to the

back of the wall plate.

Remove the existing wall plate and/or thermostat.

Label your wires.

As you remove each wire one at a time, nd

the Hunter label with the corresponding

letter code and attach it to the wire.

DO NOT DISCONNECT THE WIRES

BEFORE LABELING THEM

2. Labeling Your Wires

Tip: To prevent your wires from falling back into the wall, wrap them around a pencil.

*Only 1 reversing valve is needed to run a heat pump. If both “O” and “B” are present, “B” may be a common wire.

RH, R

Power wire for heating

Wire Identication

Power wire for air conditioning

Y, Y1

Controls your compressor outside

Controls your fan to your HVAC system

Furnace wire

Allows the heat pump to tell

the thermostat there may be a

system problem

Reversing valve for the heat

pump; allows compressor to

supply air conditioning*

Alternate reversing valve

for the heat pump; allows

compressor to supply heat*

W2 - Second stage of heat

E- Emergency heat

Aux - Auxiliary wire

Second stage of cooling

Common wire used to

power the thermostat

when available

Only used with a 3 wire hot

water heating system

Pre-Installed

Jumper Clip

3. Mounting Your Wall Plate

Insert the wires.

Pass your labeled wires through

the opening of the wall plate.

Separate the wall plate.

Pull the wall plate straight o

the back of your thermostat.

Install the top screw.

Partially tighten one

screw into the top hole.

Level the wall plate.

Install the bottom screw.

Fully tighten both screws.

C D

If you only have an RH wire,

leave the pre-installed jumper clip in

place between the RC & RH terminals.

Install the wire under the jumper clip in the

same opening.

If you have both an RC & RH wire,

lift the RC & RH levers and remove

the pre-installed jumper clip now.

4. Reconnecting Your Wires

Raise the appropriate terminal levers.

Lift the levers on the terminals that match the

labels on your wires. If one of the terminals

you need has a shield in front of it, use your

nger to break the tab away.

Insert your wires and lower the levers.

Insert each wire into its corresponding

terminal. Lower the levers and push any

excess wire back into the wall.

OPTION 1OPTION 2

5. Mounting Your Thermostat

Snap your thermostat

onto the wall plate.

Install your AA batteries.

Note: NEVER use

rechargeable batteries.

Write down your 15-digit security

code exactly as displayed.

You will need this code when you setup

your account.

ASet your system switches.

Based on the type of furnace you have:

- Select Gas/Oil or Electric

- Select Heat Pump or Conventional

EXAMPLE

If you are not sure what system

you have, contact your

HVAC manufacturer.

6. Power ON Your HVAC System Unit

You have completed your

installation!

Go to your circuit breaker panel and turn on

power to your compressor and furnace.

Turn Power

Form# 44123-01

20120814

Control from any

smartphone, tablet,

laptop or desktop

computer.

my.HunterFan.com

When the gateway light turns green, your thermostat will automatically connect to the internet.

modem/router

Tip: Lift gateway antenna to improve connectivity.

7. Connect

8. Register

9. Control

Otros manuales para Internet Thermostat

Tabla de contenidos

Otros manuales de Termostato de Hunter

Hunter

Hunter 44050 Manual de usuario

Hunter

Hunter 42345 Manual de usuario

Hunter

Hunter 44760 Manual de usuario

Hunter

Hunter 44377 Guía del usuario

Hunter

Hunter HUNTER 42203 Manual de usuario

Hunter

Hunter 40135 Manual de usuario

Hunter

Hunter Set & Save 47110A Manual de usuario

Hunter

Hunter 42122 Manual de instrucciones

Hunter

Hunter Set & Save 47250A Manual de usuario

Hunter

Hunter 44156 Manual de usuario

Hunter

Hunter 42999 44050S Manual de usuario

Hunter

Hunter 40080 Manual de usuario

Hunter

Hunter 42122 Instrucciones de montaje

Hunter

Hunter 42177 Guía del usuario

Hunter

Hunter 40120 Manual de usuario

Hunter

Hunter 44155C Manual de usuario

Hunter

Hunter 44110 Manual de usuario

Hunter

Hunter 44905 Instrucciones de montaje

Hunter

Hunter 44300 Manual de usuario

Hunter

Hunter 44360 Set & $ave Manual de usuario

Hunter

Hunter SET & SAVE 47110A Manual de usuario

Hunter

Hunter Auto Temp Plus 44422 Manual de usuario

Hunter

Hunter 40135 Manual de usuario

Hunter

Hunter 44110B Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario