Hunter Pacific Aurora Alternatives 2 Manual de usuario

Electrician

Installation Manual

Aurora Alternatives 2 Ceiling Fan

CEILING FAN MUST BE INSTALLED

BY A LICENSED ELECTRICIAN

(NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN)

*Electricians are recommended to tick off all items on the quick

checklist and fill out their details onto the back page of the Fan

Owner Warranty & Operations Manual after installation

National Warranty Line

1300 360 280

Monday to Friday from 9am to 5pm EST

Only available within Australia

Hunter Pacific International Pty Ltd, Building 8, 256 New Line Road, Dural NSW 2158 Australia

ABN :18 063 521 666

ELECTRICIANS - TO PROTECT YOUR CUSTOMER’S WARRANTY, PLEASE READ

PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT.

IMPORTANT INFORMATION

ELECTRICIANS MUST READ PRIOR TO INSTALLATION

1. Distributor and installer details and purchase receipts are essential for on-site warranty claims

and must be presented to repair personnel, make sure you record your details in the Fan Owner

Warranty and Operations Manual.

2. Fans and fixed wiring products must only be installed by persons who are appropriately licensed

by the applicable State regulatory body. Therefore, to protect our repair personnel, on-site

warranty claims will not be accepted if products have been installed by unlicensed persons.

3. Damage caused by incorrect installation, force-majeure, electrical surges, lightning, power grid

fluctuations, water or by connection to alternative power supply sources (such as solar inverters,

etc.) is not eligible for warranty repair.

4. Blades must be replaced only as a complete set. Blades are supplied only as a pre-balanced set

and the replacement of individual blades may void the warranty by causing mechanical

damage to the motor, excessive noise or premature wear.

5. When products are installed in a location requiring special access equipment (such as

scaffolding or scissor lifts, etc) the cost of providing, installing and operating special access

equipment must be borne by the site owner.

For safety, and to protect your customers warranty, the following must be taken into

account when installing and operating the product (s):

IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF

INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY

HOT LINE NUMBER 1300 360 280. BEFORE LEAVING THE JOB

SITE. PLEASE DO NOT REMOVE THE FAN FROM THE CEILING

ONCE INSTALLED UNLESS INSTRUCTED TO DO SO.

(a) DO NOT USE SOLID-STATE WALL CONTROLLERS. Neither leading nor lagging edge

controllers will give satisfactory performance. Wall controls must only be types approved

for use by Hunter Pacific International.

(b) The fan, light and bracket must be earthed.

(d) Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling,

steel structure or timber framing. If additional bracing is added it must be firmly secured to

the rafters and not left floating on the ceiling. Special mounts, such as T-hooks, are

available for certain types of installation.

(e) After installation, fan blades must be at least 2.1 m (7 feet) above floor level.

(f) The use of these products by children and the infirm must be under supervision.

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

Electrician Installation Manual

Aurora Alternative 2 Ceiling Fan

Hanger Bracket

Hex Head Screw

Ball Joint

Canopy Cover

Parts List - Aurora Alternatives 2

Blade

Blade Screw

Base Plate

Motor

Housing

Washer

Part Qty Part Qty Part Qty

Blades 4 Base Plate 1 Canopy Cover Screws 2

Blade Screws 12 HPI Wall Controller 1 Canopy Cover 1

Blade Washers 12 Hanger Bracket 1 Motor Housing 1

Wall Speed Capacitor 1 Hex Head Screw 2

Ball Joint 1 15cm Down Rod 1 Reversing Switch Cover 1

Ball Joint Screw 1 Down Rod Pin Screw 1 (these parts come preassembled)

Ball Joint Pin 1 Down Rod Short Screw 1

Plug

Lower Rim

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

STEP 3 (Fig. 3)

a) TIGHTEN THE GRUB SCREW.

(This is important to ensure the fan will not

wobble and the weight of the fan is supported).

b) Hang the ball joint into the hanger bracket.

Ensure the groove on the hanger bracket is

locked into the slot on the ball joint.

Assembling the fan

STEP 2 (Fig. 2)

a) Drill a hole in the timber nogging for wiring.

b) Use the two hex screws to secure the hanger

bracket onto the timber nogging. The timber nog-

ging should be supplied by the installing electri-

cian and must be supported between the two ceil-

ing joists as shown in the diagram above.

STEP 1 (Fig. 1)

PERFORM THIS STEP IF THE WIRES HAVE NOT

BEEN FED THROUGH THE DOWN ROD.

a) Loosen the ball joint screw and remove the

ball joint pin to separate the down rod from the

ball joint.

b) Feed wires from motor housing up and

through the down rod.

c) Insert the down rod pin into the connection

collar and the down rod cotter pin (avoid pinch-

ing wires). Clip in the cotter pin key and secure

down rod with the other shorter down rod screw

provided.

d) Slide on canopy cover and refit the ball joint.

If an extension rod needs to be installed

please go to page 11.

Hanger

Bracket

Down Rod

Fig. 2

Timber Nogging

Hex Head Screw

Hanger

Bracket

Fig. 3

Ball Joint

Canopy

Washer

Cotter Key

Down Rod

Screw

Connection Collar

Cotter Pin

Fig. 1

Reverse

Switch

Cover

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Assembling the fan

Fig. 4

Green

Earth Wires

STEP 4 (Fig 4 & 5)

a) Connect wires from the fan to wires in the ceiling via the

terminal block on the hanger bracket (refer to figure 4 and 5).

b) Make sure earth wires are also connected.

c) Connect light wires (red/white) if a light fitting is going to be

used. (Cap seal light wires if a light fitting is not going to be

used).

Wiring Instructions (with and without accessory light)

Brown

Blue

Red/White Earth

Wires

Supply

E N A

LA LA

FA LA E N

Green-yellow

Black

Red

Brown

White or Red

Green-yellow

Blue

Fan Wiring

Combi

Control

Separate

Control

Separate terminal

For when 3 pole

Block is fitted.

Wiring for use with 3 pole block

- Colours representative only

- Separate extension terminal for active

for light when 3 pole block fitted.

Fig. 5

STEP 5 (Fig 6)

a) Slide canopy cover up and over the hanger bracket.

b) Twist the canopy to locate screws holes then loosen

canopy screws half way.

c) Now twist the canopy cover in the

opposite direction and fully tighten screws until the can-

opy cover is stabilised.

Fig. 6

Hanger

Bracket

Canopy Cover

Down Rod

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Assembling the fan

Fig. 7 STEP 6 (Fig 7)

a) Attach blades to the blade holders on the

motor housing using the 3 screws and

washers provided.

b) Repeat this procedure for the other 3

blades.

Blade Holder

Blade Screw

Blade Washer

Blade

Switch Cover

Reverse

Switch

STEP 7 (Fig 8)

a) Lift the switch cover to expose the reverse switch.

b) The reverse switch should be pushed fully to the

left for Summer (fan spins anticlockwise) and

pushed fully to the right for Winter (fan spins clock-

wise).

c) Make the sure reverse switch is not stuck in its

neutral position otherwise the fan will not spin.

Fig. 8

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Attaching an accessory light kits—Aurora2 light kit

STEP 2 (Fig. 10)

a) Use the connectors to attach the light wires from

the motor housing to light assembly kit.

b) Attach and secure the light assembly kit using the

3 screws provided.

STEP 3 (Fig. 11)

a) Plug the light globe into the socket. DO NOT

touch the light globe with your fingers.

b) Gently push the glass cover upwards and turn it to

attach the light glass to the fan.

78mm halogen light (MAX 100W) E14 light ( MAX 2x40W)

STEP 2 (Fig. 13)

a) Use the connectors to attach the light wires from

the motor housing to light assembly kit.

b) Attach and secure the light assembly kit using the

3 screws provided.

STEP 3 (Fig. 14)

a) Install the light bulbs in the light sockets.

b) Gently push the glass cover upwards and turn it to

attach the light glass to the fan.

Fig. 9

Lower Rim

Screws

STEP 1 (Fig. 9)

a) Turn base plate to remove the plug and base plate

from the motor housing.

b) Loosen screws to remove the lower rim.

Lower

Rim

Screw

Light wire

connectors

Upper Mounting

Rim

Fig. 10

Lug Groove

Fig. 11

Glass Cover

Fig. 12

Lower Rim

Screws

STEP 1 (Fig. 12)

a) Turn base plate to remove the plug and base plate

from the motor housing.

b) Loosen screws to remove the lower rim.

Lower

Rim

Screw

Light wire

connectors

Upper Mounting

Rim

Fig. 13

Fig. 14

Lug

Groove

Glass Cover

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

1. Do not attempt to operate the fan (or

optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

Attaching an accessory light kit — Aurora2 light kit

STEP 4 (Fig. 18)

a) Turn the light to attach it firmly to the light

socket.

b) Gently push the glass cover upwards and

turn it to attach glass cover to the fan.

Fig. 18

STEP 3 (Fig. 17)

a) Fit the compact fluorescent light to the

light socket.

Fig. 15

Lower Rim

Screws

STEP 1 (Fig. 15)

a) Turn base plate to remove the plug and base plate

from the motor housing.

b) Loosen screws to remove the lower rim.

GX53M 14W compact fluorescent light

Lower

Rim

Screw

Light wire

connectors

Upper Mounting

Rim

STEP 2 (Fig. 16)

a) Use the connectors to attach the light wires from

the motor housing to light assembly kit.

b) Attach and secure the light assembly kit using the

3 screws provided.

Fig. 16

Light Socket

Compact

Fluorescent

Light

Fig. 17

Groove

Lugs

Glass Cover

Compact

Fluorescent

Light

Fig. 18

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Attaching an accessory light kit — Standard accessory light kit

Motor

Housing

STEP 1 (Fig. 19)

a) Turn base plate anticlockwise to

remove the plug and base plate from the

motor housing. Do not throw away base

plate away.

Fig. 19

Plug

Base Plate

STEP 2 (Fig. 20)

a) Loosen screws to remove the light kit rim.

Fig. 20

Screws Lower Rim

STEP 3 (Fig. 21)

a) Once the motor housing lower rim is

removed, the light wires coming from the

motor housing should be exposed.

b) Cut and remove wire connectors.

c) After removing the wire connectors feed

the light wires through the thread of the

motor housing lower rim.

d) Tighten screws (removed from step 2) to

secure the motor housing lower rim back

onto the motor housing upper rim.

Fig. 21

Motor Housing

Upper Rim

Cut and remove

wire connectors

Screw

Thread

Lower Rim

Electrician Installation Manual

Aurora Alternatives 2 Ceiling Fan

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Attaching an accessory light kit — a standard accessory light kit

Light Wires

Base Plate

STEP 4 (Fig. 22)

a) Feed wires from the motor housing lower rim

through the hole in the centre of the base plate .

b) Attach the base plate to the motor.

Fig. 22

STEP 5 (Fig. 23)

a) Feed wires through the thread of the upper

part of the light kit.

b) Secure upper part of the light kit to the

motor housing by tightening the thread.

c) Connect light wires to the terminal block in

the lower part of the light kit.

d) Secure the lower part of the light kit to the

upper part of the light kit by the tightening the

light kit screws.

e) Fit light globes in to the light kit.

(note: Only specified globes should be used).

Fig. 23

Thread

Screw

Light

Wires

Terminal

Block

Lower

Part of Light

Kit

Upper Part

of Light Kit

Tabla de contenidos

Otros manuales de Admirador de Hunter Pacific

Hunter Pacific

Hunter Pacific Typhoon Mach 2 Timber Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Everglade Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Coolah Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Palm Manual de usuario

Hunter Pacific

Hunter Pacific RADICAL 2 Manual de instrucciones

Hunter Pacific

Hunter Pacific Intercept II Manual de usuario

Hunter Pacific

Hunter Pacific Icon 52 Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Penta Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Magnum Manual de usuario

Hunter Pacific

Hunter Pacific Typhoon Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Micro Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Duo Manual de usuario

Hunter Pacific

Hunter Pacific Majestic Little Bay Manual de usuario

Hunter Pacific

Hunter Pacific Attitude Manual de usuario

Hunter Pacific

Hunter Pacific THE WOOD Series Manual del propietario

Hunter Pacific

Hunter Pacific Icon Fan Manual de usuario

Hunter Pacific

Hunter Pacific Typhoon Timber 42" Manual de usuario

Hunter Pacific

Hunter Pacific Concept Manual de usuario

Hunter Pacific

Hunter Pacific VortX V500i Guía de instalación

Hunter Pacific

Hunter Pacific X-OVER DC Manual de instrucciones

Hunter Pacific

Hunter Pacific POLAR DC P3B2571 Manual de instrucciones

Hunter Pacific

Hunter Pacific Majestic Rosewood Manual de usuario

Hunter Pacific

Hunter Pacific AQUA DC AIP2661 Manual de instrucciones

Hunter Pacific

Hunter Pacific Coolah Manual de instrucciones

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje