Humanscale Quickstand Manual de usuario

INSTALLATION INSTRUCTIONS

PARTS REQUIRED

Single QuickStand Parts

A (1) QuickStand Unit

B (1) Base Plate

C (1) Platform

D (1) Palm Support

E (1) VESA Plate

F (6) M8 x 18 mm Flat Head Machine Screws

G (4) M4 x 18 mm Pan Head Phillips

H (4) M4 x 8 mm Pan Head Phillips

I (4) VESA Spacer

Additional Parts for Dual Monitor QuickStand

J (1) Dual Monitor Crossbar

K (1) M6 x 22 mm Flat Head Machine Screws

L (2) M5 x 18 mm Flat Head Machine Screws

M (2) VESA Plate

N (8) M4 x 18 mm Pan Head Phillips

O (8) M4 x 8 mm Pan Head Phillips

P (8) VESA Spacer

3 mm Hex Key (supplied)

4 mm Hex Key (supplied)

5 mm Hex Key (supplied)

6 mm Hex Key (supplied)

Box Knife

Tape Measure

#2 Phillips Screwdriver

Flat-Head Screwdriver

Hardware

Tools Required

www.humanscale.comCustomer Service: N America +1 800 400 0625 / International +353 (0)1 858 0910

STEP 1

Remove Shipping Plate

Tools: 6 mm Hex Key

• Lay the QuickStand unit on the work surface facing up

and unscrew the (2) M8 x 10 mm Cap Head Machine

Screws holding the Shipping Plate in place (ﬁg. A)

• Set aside the (2) M8 x 10 mm Cap Head Machine

Screws and the Washers for Step 3

Read all instructions carefully before installing this product or attempting to use it

This product contains a loaded mechanism that is under tension. Do not attempt to

remove or alter any part of this product or in any way modify or tamper with any

component of this product other than as set forth in these instructions. Failure to

comply with the instructions provided may result in property damage or serious injury.

Do not remove bracing box attached to QuickStand unit until your QuickStand is

fully assembled

WARNING

STEP 2

Attach Base Plate

Tools: 5 mm Hex Key

• Secure the Base Plate in place using (6) M8 x 18 mm

Flat Head Machine Screws (ﬁg. B)

STEP 4

Measure Work Surface Depth

IMPORTANT: Please check the depth of your work surface

- If you are installing a QuickStand with a Large Platform, your QuickStand

is pre-set to attach to a 29” (750 mm) deep work surface

- If you are installing a QuickStand with a Small Platform, your QuickStand

is pre-set to attach to a 23” (600 mm) deep work surface

Tools: Measuring Tape

• The distance between the front edge of the Platform to

the inside face of the Base Clamp must be equal to the

work surface depth (ﬁg. D)

• If the Base Clamp is in the correct position, please proceed to step 6

• If the Base Clamp needs to be adjusted, please proceed to step 5

STEP 5

Adjust Base Clamp for Correct Work Surface Depth

Tools: Measuring Tape

5 mm Hex Key

• Loosen or remove the (4) M8 x 10 mm Pan Head Machine

Screws and slide/reposition the Base Clamp to achieve the

correct work surface depth (ﬁg. E)

NOTE: If you will be installing the Grommet Mount/Bolt-through

base instead of the clamp, please refer to the Grommet Mount/Bolt-

through kit instructions now.

STEP 3

Attach Platform

Tools: 6 mm Hex Key

• Ensure the Platform is equally spaced from

the Base Plate on either side (ﬁg. C)

• Using the (2) M8 x 10 mm Cap Head Machine

Screws and the Washers from step 1, secure

the Platform to the QuickStand unit

Base Plate

Platform

STEP 6

Attaching QuickStand to the Work Surface

IMPORTANT: Your QuickStand unit is heavy. If needed, please

have assistance when lifting.

• Carefully lift your QuickStand unit from its horizontal position

to its vertical position (ﬁg. F)

• Tighten the two thumbscrews to clamp your QuickStand unit

to the back edge of the work surface

STEP 7

Mounting Single Monitor

If you are installing a dual QuickStand unit please proceed to Step 8

Tools: #2 Phillips Screwdriver

• Make sure the top of the VESA Plate is

facing towards the top of the monitor

before securing

• Screw down the VESA Plate using the hardware

kit supplied (ﬁg. G)

• Slide the monitor into the quick-connector on the QuickStand unit (ﬁg. H)

• Plug the Power Cord and DVI Cable into the monitor

• Once your monitor is in position, please proceed to Step 10

STEP 8

Attaching Crossbar for Dual Monitors

Tools : 3 mm Hex Key

4 mm Hex Key

• Attach Dual Monitor Crossbar to QuickStand unit

using the hardware kit supplied (ﬁg. I)

STEP 9

Attaching Dual Monitors

Tools: #2 Phillips Screwdriver

• Make sure the top of the VESA Plates are facing towards

the top of the monitor before securing

• Screw down the VESA Plates using the hardware kit supplied (ﬁg. J)

• Slide each monitor into the quick-connector on the Dual Monitor Crossbar (ﬁg. K)

• Plug the Power Cord and DVI cable into each monitor

STEP 11

Attaching USB Devices

Tools: Flat-Head Screwdriver

• Using a Flat-Head Screwdriver if needed, remove cable cover by tilting out from the bottom (ﬁg. M)

• Route USB cables from keyboard and mouse into cable bracket (ﬁg. N)

• Carefully pull cable slack through bracket until cable heads are set within. Wrap remaining cable slack around bracket (ﬁg. O)

• Replace cable bracket cover (ﬁg. P)

STEP 10

Secure Palm Support

• Peel off sticker backing from Palm Support and place down

in your desired position on the front edge of the Platform (ﬁg. L)

NPO

STEP 12

Removing Brace Box

• Remove tape and lift out box. (ﬁg. Q)

STEP 13

Adjusting Weight Capacity

WARNING: Do not use a Power Drill to adjust the tension adjuster

Tools: 6 mm Hex Key

• Remove top cover from QuickStand unit to expose

the tension adjuster screw (ﬁg. R)

• Slowly begin to turn the tension adjuster

screw clockwise to increase the tension (ﬁg. S)

• We recommend turning the tension adjuster

screw 10 revolutions at a time before checking to

see if your QuickStand is correctly balanced

• Once you have adjusted your QuickStand, try raising and

lowering a few times until it ﬂuidly adjusts. Your QuickStand

should stay where you set it

• If you need to make further adjustments,

please follow these steps again

ADJUSTING QUICKSTAND

In order to be able to raise and lower your QuickStand with ease, it is important to spend some time adjusting the tension adjuster which

can be located in the top of the QuickStand unit

Increase Weight Capacity – If the platform is too heavy

to raise but easy to lower and does not stay in place when

raised, please adjust the tension adjuster

Decrease Weight Capacity – If the platform is too easy

to raise but difﬁcult to lower and does not stay in place

when lowered, please adjust the tension adjuster

–

STEP 14

Adjusting Monitor Height

SINGLE QUICKSTAND

• Hold each side of your monitor and manually

raise or lower until it is in the correct position (ﬁg. T)

DUAL QUICKSTAND

Tools: 6 mm Hex Key

• Remove top cover of the carriage assembly (ﬁg. V)

• Slowly begin to turn the monitor height adjustment

screw clockwise to raise the monitors and

counter-clockwise to lower the monitors (ﬁg. W)

STEP 15

Adjusting Monitor Tilt

SINGLE AND DUAL QUICKSTAND

• Hold the top and bottom of your monitor

and manually adjust the monitor tilt until the

desired angle is achieved (ﬁg. X)

STEP 16

Adjusting Monitor Orientation

SINGLE AND DUAL QUICKSTAND

• Hold each side of your monitor and

manually turn the monitor until the desired

orientation of either landscape or portrait

is achieved (ﬁg. Y)

STEP 17

Correctly Setting Up Your Workstation

SINGLE AND DUAL QUICKSTAND

• Adjust the platform until the keyboard

is at or just below elbow height

• If needed, manually adjust the monitor up or down until

the top line of text on the screen is at eye level

+15º

-5º

±90º

Otros manuales para Quickstand

Tabla de contenidos

Otros manuales de Rack y soporte de Humanscale

Humanscale

Humanscale QuickStand Eco Manual de usuario

Humanscale

Humanscale QuickStand Under Desk Manual de usuario

Humanscale

Humanscale UFEA Manual de usuario

Humanscale

Humanscale V6 Wallstation Instrucciones de instalación

Humanscale

Humanscale M8.1 Manual de usuario

Humanscale

Humanscale M/FLEX Manual de usuario

Humanscale

Humanscale M2.1 Manual de usuario

Humanscale

Humanscale M/FLEX Manual de usuario

Humanscale

Humanscale Quickstand Manual de usuario

Humanscale

Humanscale QuickStand Eco Manual de usuario

Humanscale

Humanscale M/Connect 2 Manual de usuario

Humanscale

Humanscale Thin Client Holder Manual de usuario

Humanscale

Humanscale QUICKSTAND LITE Manual de usuario

Humanscale

Humanscale Quickstand Manual de usuario

Humanscale

Humanscale M10 Manual de usuario

Humanscale

Humanscale M2.1 Manual de usuario

Humanscale

Humanscale V6 Manual de usuario

Humanscale

Humanscale CPU 450 Manual de usuario

Humanscale

Humanscale HSIKB0417 Manual de usuario

Humanscale

Humanscale M7 Manual de usuario

Humanscale

Humanscale M/FLEX Manual de usuario

Humanscale

Humanscale Mesh Guía de configuración

Humanscale

Humanscale M2.1 Manual de usuario

Humanscale

Humanscale V/Flex Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario