Hubbell RDS50Z Manual de usuario

Installation Instruction for new

construction of a Door Jamb Switch

Kit (RDS50Z) Normally Closed

Door open lights ON, Door closed

lights are OFF.

3A, 125 Vac. 4.6 Cu Inch.

NOTICE: For installation by a qualified electrician in accordance with national and local electrical codes and the

following instructions.

CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing.

CAUTION: Make sure that you follow local Electrical rules and regulations. If unsure, consult a qualified electrician.

NOTE: Do not install on a Metal door frame

NOTE: Use Copper Conductors only.

1) Create suitable cable entry in Door Frame.

2) Make an opening in Door Jam to suit Junction Box. (See

Fig. 2 for dimensions of Box). Create recess for Box

Ears to ensure Switch Plate is flush to door jamb when

installed.

3) Remove a knock out in Junction Box to accommodate

cable entry.

4) Insert cable through knock out and secure to box with

approved connector (not provided).

5) Fasten box to door jamb with 4 wood screws

(provided).

6) Connect GREEN/ BARE (ground) wire to ground screw

in back of junction box, connect Line and Load wires to

switch pig tail wires following national and local

electrical codes Use Fig. 1 for guidance.

7) Adjust shaft to proper depth on switch plate using

locknuts (provided) at the back and front of the switch

assy’ for contact with round kicker plate .

8) Using 2 short screws (provided), fasten the switch

plate to the box.

9) With power ON, Open and close door to verify proper

operation of the switch and adjust switch depth

accordingly.

10) Once proper positioning is established, install the

round kicker plate on the door side to face the switch

button, by fastening with the wood screw (provided).

11) Installation is complete.

Fig. 2 Fig. 3

Supply runs directly to the fixture

Tabla de contenidos

Otros manuales de Cambiar de Hubbell

Hubbell

Hubbell Killark VWSQ Series Manual de instrucciones

Hubbell

Hubbell 2210 Manual de usuario

Hubbell

Hubbell 4310 Manual

Hubbell

Hubbell Reversing Drum Controller 58-GJ2 Manual

Hubbell

Hubbell SNAPConnect Series Manual de usuario

Hubbell

Hubbell H-MOSS AP Manual de usuario

Hubbell

Hubbell CIRCUIT-LOCK Manual de usuario

Hubbell

Hubbell Euclid 100E Manual de usuario

Hubbell

Hubbell CIRCUIT-LOCK Series Guía de configuración

Hubbell

Hubbell Euclid 4220 Manual de usuario

Hubbell

Hubbell MOTORQUICK Manual de usuario

Hubbell

Hubbell 2243 Manual de usuario

Hubbell

Hubbell Euclid PBP Pendant Manual de usuario

Hubbell

Hubbell Circuit-Lock Manual de usuario

Hubbell

Hubbell iDevices IDEVZ01DW Manual de usuario

Hubbell

Hubbell C5027 Manual

Hubbell

Hubbell WL Series Manual de usuario

Hubbell

Hubbell 2200 Manual de usuario

Hubbell

Hubbell CHANCE M3 Instrucciones de instalación y funcionamiento

Hubbell

Hubbell EUCLID Instrucciones de instalación y funcionamiento

Hubbell

Hubbell Limit Switches Manual de usuario

Hubbell

Hubbell Euclid 4225 Manual de usuario

Hubbell

Hubbell 58-GC5026 Manual

Hubbell

Hubbell M3 Manual de programación

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario