Huawei UPS5000-S-600 Manual de usuario

Issue: 04

Part Number: 31509969

Date: 2019-06-20

UPS5000-S-600 kVA

Quick Guide (Three-phase, Three-wire)

1Overview

UPS Model Weight Dimensions (H x W x D)

UPS5000-S-600K-NN 950 kg 2000 mm x 1400 mm x 850 mm

(1) Power modules

(2) Control module

(3) Mains surge protection box

(4) Bypass surge protection box

(5) Fan power module

(6) Bypass module

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools during installation.

3. Only engineers certified by Huawei or its agents are allowed to install, commission, and

maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the UPS

faults caused are beyond the warranty scope of Huawei.

2Installing the UPS

The UPS can be installed on channel steel or the floor. Install the UPS based on site requirements.

Floor installation: Determine the UPS mounting holes using the marking-off template, drill holes,

and install the expansion sleeves of the M12x60 expansion bolts in the mounting holes.

Channel steel installation: Ensure that the distance between the outer surfaces of two pieces of

channel steel is 800 mm and secure the channel steel to the floor using expansion bolts.

Huawei does not provide channel steel or expansion bolts used for securing channel steel. The

customer should purchase channel steel (recommended width: 50 mm or more) and expansion

bolts.

Determining the UPS Installation Position

2.1

A: mounting holes on the channel steel

B: mounting holes on the floor

Unit: mm

•Floor mounting: Use eight M12x60 expansion bolts to secure the cabinet to the ground.

•Channel steel mounting: Use eight M12x60 common bolts to secure the cabinet to channel

steels.

Securing the UPS

2.2

(1)

Cabinet mounting holes (ground installation mode)

(2)

Cabinet mounting holes (channel steel installation mode)

Installing the Front, Rear, Left, and Right Anchor Baffle Plates

2.3

3Connecting Cables

1. This document uses dual mains as an example.

2. Single mains does not need bypass input power cables connected or connecting copper bars

removed.

3. During cable installation, reserve the removed screws, front power distribution covers, and rear

cover. Reinstall them after connecting cables.

NOTE

UPS Cable Connection Reference

3.1

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinet in a timely manner. Ensure that there is no

foreign matter inside and around the cabinet.

Installing Cables

3.2

2. Remove the cover from the top of the bypass

cabinet based on the cable route and cable

dimensions.

1. Open the front door of the bypass cabinet,

and remove front power distribution covers.

(1) Cover for power cables

(2) Signal cable hole

3. Remove the rear cover from the bypass cabinet,

and then remove the connecting copper bars

between the mains input terminals and bypass

input terminals. (If the mains input and bypass

input share a power source, skip this step.)

4. Connect the ground cable to the UPS.

6. Connect the output power cables.5. Connect the mains input power cables.

7. Connect bypass input power cables. 8. Connect the battery cables.

9. Connect signal cables.

The figure shows the signal cable routing and is for reference only. Connect the cable based on

the actual situation.

NOTE

4Installation Verification

1. Check that there is no foreign matter at the top and bottom of the cabinet, copper bars, and the

rear of modules.

2. (Remove the paper protective film from the

sealing putty.) After routing cables and

verifying cable connections, seal the gap

between cables and the cabinet using sealing

putty.

Dustproof cover

3. After verifying the installation, reinstall all

the covers. After the installation is complete,

reinstall the dustproof cover to prevent dust

inside if the UPS is not to be powered on

immediately.

Bottom

Copper bars

Top

Sealing putty

Sealing putty must be used as a whole and the

gap can be sealed only from the top.

Paper

protective film

5Powering On and Starting the UPS

1. Before powering on the UPS, ensure that all the items in the UPS5000 Commissioning and

Acceptance Report and Chapter 4 have been checked.

2. Measure the voltage and frequency where the external input switch is located. 380 V AC/400 V

AC/415 V AC/420 V AC voltage system: 138–485 V AC (line voltage), 480 V AC voltage system:

192–528 V AC (line voltage), and the frequency range is 40–70 Hz.

3. Before you power on the UPS, check that all external switches are OFF.

Powering On the UPS

5.1

Close the external bypass and mains input switches.

After the UPS is powered on, it starts initialization. The LCD

displays the Huawei logo and an initialization progress bar.

Initial Startup

5.2

Download and install the Service Expert app.

After login, tap Power-on password activation

on the screen. A message is displayed,

indicating whether to start the UPS. Tap OK.

Insert the WiFi module into the USB port on the

MDU. Enable the mobile phone WLAN, search

for the UPS_WIFI signal, and connect to the

WiFi signal. The password is Changeme.

Set the Site and Device Type as required, and

connect the device. Set IP to 192.168.0.10, Port

to 443, Username to admin, Password to

Changeme, and click Login.

Enter Bar code and Verification code

obtained from the LCD on the Offline

Activation screen. Tap Generate PWD to

generate a startup password.

Set Site and Device Type as required,

and tap Offline Activation.

Enter the generated password in the

password textbox on the LCD to start the

UPS.

Use the app to

start the UPS

online?

Yes

No, start the

UPS offline

On the app home screen, tap StartUp to access the Set Startup screen.

•If the UPS is powered on for the first time, you need to obtain the startup password from the

Service Expert app. Skip this step if the UPS is not powered on for the first time.

•The Service Expert app can be downloaded from Google Play Store and can run on Android.

1. Obtain the startup password.

2. Set the language, time, date, network parameters, and system parameters on the Settings

Wizard screen.

3. After you perform the settings, the Bypass mode and No battery alarms are reported by the

MDU and do not need to be cleared. If there is any other alarm, you need to rectify the fault.

4. View the system running status diagram on the MDU to check that the UPS is working in bypass

mode.

1. Set system parameters with caution because normal UPS operation depends on correct settings.

Set Single/Parallel with caution. Incorrect setting may affect the normal UPS operation.

Output Voltage level refers to the line voltage level. Set it based on site requirements.

Set Output frequency correctly. Otherwise, the UPS may not work properly and loads may be

affected.

2. Battery parameter settings have great impact on battery maintenance, battery lifespan, and

discharge time.

System User LCD Preset Password WebUI Preset Password

admin (system administrator) 000001 Changeme

operator (common user) 000001 Changeme

To ensure system security,

change the LCD and WebUI

passwords after the first login.

NOTE

1. On the main menu, choose Common Functions and tap

Inv. ON.

2. In the displayed login window, enter the user name and

password, and tap .

3. In the displayed dialog box, tap Yes to start the inverter.

1. After the inverter starts, the UPS works in normal mode. The Bypass mode alarm disappears.

Check that the UPS has transferred to normal mode by viewing the system running status

diagram. Check that the UPS three-phase output voltage and frequency are normal by viewing

AC Output on the MDU. Use a multimeter to check that the valid three-phase output voltage

and frequency are normal.

2. After confirming that the battery strings are properly connected, close the battery string input

circuit breaker. If there are multiple battery strings, close the circuit breaker for each battery

string and then the general circuit breaker between battery strings and the UPS. The No battery

alarm disappears from the MDU.

3. Close the external output switches to supply power to loads.

Powering On Loads

5.4

(Optional) Setting Parameters for the BCB Box

5.5

(Optional) If a BCB box is configured, choose Settings > Dry Contact Set, set MUE05A

connection to Enable, and then set BCB connection [OL] and Battery breaker [STA] to Enable.

Starting inverter

5.3

Otros manuales para UPS5000-S-600

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de Huawei

Huawei

Huawei UPS5000-H Series Manual de usuario

Huawei

Huawei UPS5000-E-40 kVA Manual de usuario

Huawei

Huawei UPS2000-G-6 kVA Manual de usuario

Huawei

Huawei UPS5000-A-30 kVA Manual de usuario

Huawei

Huawei UPS5000-E-300K-SM Manual de usuario

Huawei

Huawei UPS5000-A-400K-FTS Manual de usuario

Huawei

Huawei UPS5000-E-****-FM series Manual de usuario

Huawei

Huawei PDU8000 Series Manual de usuario

Huawei

Huawei UPS5000-S Series Manual de usuario

Huawei

Huawei UPS5000-A series Manual de usuario

Huawei

Huawei UPS5000-A-500 kVA Manual de usuario

Huawei

Huawei UPS5000-S-600 Manual de usuario

Huawei

Huawei UPS2000-G-1KRTS Manual de usuario

Huawei

Huawei UPS5000-A-30 kVA Manual de usuario

Huawei

Huawei iSitePower-M Manual de usuario

Huawei

Huawei UPS2000-A-1 kVA Manual de usuario

Huawei

Huawei UPS5000-S-1600 kVA Manual de usuario

Huawei

Huawei UPS5000-A-400 kVA Manual de usuario

Huawei

Huawei UPS2000-G-3KRTL-V2 Manual de usuario

Huawei

Huawei UPS5000-H-1200K-NT Manual de usuario

Huawei

Huawei PDC-0038V4ACIOA-V2 Manual de usuario

Huawei

Huawei UPS5000-A-200 Series Manual de usuario

Huawei

Huawei UPS5000-S Series Manual de usuario

Huawei

Huawei UPS5000-A-300K-FT Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario