Huawei SmartAX MA5800-X2 Manual de usuario

HUAWEI TECHNOLOGIES CO., LTD.

SmartAX MA5800-X2

Quick Installation Guide

Issue: 01

Date: 2016-10-28

Intended Audience

About This Document

Symbol Conventions

This document describes how to install the MA5800-X2.

The intended audience is hardware installation engineers.

The symbols that may be found in this document are defined as follows.

Symbol Description

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in equipment damage, data loss, performance deterioration, or

unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury,

equipment damage, and environment deterioration.

Content

1 Precautions …………………………………..…………………………............................………….1

2 Tools and Meters………………………….………………………….............................…………….2

3 Appearance and Structure……………………………….............................…………….3

4 Environment Requirements on Third-Party Cabinets ………………………........................4

5 Space Requirements on Third-Party Cabinets …………….…………........................4

5.1 When the Cabinet Accommodates One MA5800-X2 Subrack...................................4

5.2 When the Cabinet Accommodates Two Subracks………………………….…………...5

6 Installing the Installing the Service Subrack..…....................................................………...7

6.1 Installation in the Cabinet or Rack ………………….............................................................7

6.2 Installation in the Network Cabinet of the Customer ............................................................8

6.3 Guide for Grounding the Network Cabinet of the Customer..................................................9

7 Routing Cables …………………………………………………..................................…...10

7.1 Routing the PGND Cable and the External Power Cable….................................................10

7.2 Routing Network Cables………….……………………....................................................................13

7.3 Routing Optical Fibers…………………………………………………………..............................................14

8 Checking the Installation ……………………………………………..............................….......15

9 Powering On the System ………………….…………………………..............................….......16

1 Precautions

•After routing the cable, attach the label or fasten the tag to the cable 20 mm away from the

connector.

•After the label for the signal cable is attached to the signal cable, the rectangular text area of

the label must face rightwards or downwards.

•After the identification plate for the power cable is attached to the power cable, the text area of

the plate must face rightwards or upwards. Ensure that the side attached with the label faces

outwards.

ESD gloves ESD wrist strap

Affixing labels / tags

•This document aims to provide simple and distinctive guidelines for hardware installation.

•This document does not describe operations for the pre-delivery installation of the internal

cables and so on. Instead, this document describes only the operations for on-site

installation.

Electrostatic Discharge

Before touching the device, or holding the boards and IC chips, wear the ESD gloves or the

ESD wrist strap to prevent the electrostatic discharge of the human body from damaging the

sensitive components. Ensure that the other end of the ESD wrist strap is properly grounded.

•The distance between cable ties or binding straps inside the cabinet must be within 250 mm.

(For user cable, the distance must be within 200 mm.)

•Use diagonal pliers to cut off the extra part of the cable tie to the end, and ensure that the

cable tie is neat without sharp edges to prevent hand injury.

Bundling cables

2 Tools and Meters

ESD gloves ESD wrist strap

Optical power meterMultimeter

Network cable

crimping tool Network cable tester

Before you begin, get the following tools ready.

Marker Flat-head screwdriver Phillips screwdriver Diagonal pliers

Cable cutter Paper knife

Adjustable wrench Mounting bar Measuring tape Cable cutter

Optical fiber

cleaner

Optical fiber

microscope

3 Appearance and Structure

Control board

Unit: mm

IEC

Mounting

bracket

482.6

442.0

268.7

88.1

535.0

442.0

268.7

88.1

ETSI

Mounting

bracket

Power board Fan tray

ESD jack Grounding

point

Cabling teeth Service board

IEC

Mounting

bracket

ETSI

Mounting

bracket

Service Subrack (with IEC mounting bracket)

Service Subrack (with ETSI mounting bracket)

4 Environment Requirements on Third-Party Cabinets

•Cabinet dustproof requirement: The MA5800-X2 subrack is not dustproof, so select

dustproof cabinets that support dust filter maintenance.

•Cabinet installation requirements:

For the MA5800-X2 service subrack, select an IEC-compliant cabinet with a depth of 300 mm or

more so that a space with a depth of 55 mm or more can be reserved for cable/fiber routing

after boards are installed.

After the MA5800-X2 is installed in an ETSI-compliant cabinet that meets the related

requirements, replace the mounting ears with the ETSI-compliant mounting ears customized

by Huawei for the MA5800-X2.

•Cabinet door requirement: When devices are operating, keep the cabinet door closed.

•Grounding requirement: Huawei cabinets are grounded through mounting bars. Ensure that

third-party cabinets are properly grounded based on site conditions.

•Power distribution requirements: Ensure that an over-current protection mechanism has

been deployed on the upper-level device. A 20-A DC over-current protection mechanism and

an 8-AAC over-current protection mechanism are recommended for the MA5800-X2. Ensure

that the circuit breaker trip value of the upper-level device is greater than or equal to the rated

value on the device nameplate.

•Heat dissipation requirements:

Ensure that the cabinet has an air inlet and the hole density of the cabinet door is 60% or

higher.

When a cabinet accommodates multiple subracks or the device shares a cabinet with other

active devices, ensure that the following space requirements are met.

5.1 When the Cabinet Accommodates One MA5800-X2 Subrack

•The MA5800-X2 supports left-in right-out heat dissipation, so the cabinet must have an

unblocked air inlet on its door.

•You are advised to reserve more than 4 U space above and under the MA5800-X2

respectively to minimize the impact on other components in the cabinet.

•Ensure that the fan tray is not blocked by the cable routing. If the fan tray is blocked, it cannot

be smoothly removed or installed.

Front view Side view

Airflow blocking object

5 Space Requirements on Third-Party Cabinets

•Reserve 10 U space between the devices or add a 3 U air deflector to redirect air flows to

minimize the mutual heat dissipation impacts on the devices.

•Reserve at least 4 U space when you route fibers or install other passive devices to facilitate

subsequent air inlet or dust filter cleaning.

Without an air deflector With an air deflector

Front view Side view Front view Side view

10U

If the MA5800-X2 subrack is installed in a subrack with B-T airflow, you are advised to add

an air deflector to the subrack so that the hot air does not direct flow to the MA5800-X2.

When 2 U space is reserved at the air inlet and 3 U space is reserved at the air outlet, the

cabinet panels will have less impact on the heat dissipation of the MA5800-X2.

Active device

When the cabinet accommodates two MA5800-X2 subracks or one MA5800-X2 subrack and

another device

5 Space Requirements on Third-Party Cabinets

Air deflector (3 U)

5.2 When the Cabinet Accommodates Two Subracks

6 Installing the Service Subrack

6.1 Installation in a Cabinet or a Rack

•Use the IEC mounting bracket when the service subrack is installed in the IEC cabinet or rack.

•Install the mounting ears of the IEC subrack, and then install the mounting ears of the ETSI

subrack on the mounting ears of the IEC subrack.

•If the cable manager is not configured, a 1 U high space on the top of MA5800-X2 must be

reserved for routing cables.

IEC mounting ear

Installing mounting ear

Installing floating nut

Installing in the cabinet

Cable manager (Optional)

Floating nut

Mounting bar (Use a flat-head screwdriver

if no mounting bar is available)

Tabla de contenidos

Otros manuales de Terminal táctil de Huawei

Huawei

Huawei EchoLife HG813 Manual de usuario

Huawei

Huawei OptiXstar K153-10 Manual de usuario

Huawei

Huawei F316 Manual de usuario

Huawei

Huawei ETS2226 Manual de usuario

Huawei

Huawei B160 Manual de usuario

Huawei

Huawei EchoLife HG8240 Manual de usuario

Huawei

Huawei ETS2555 Manual de usuario

Huawei

Huawei ETS3023 Manual de usuario

Huawei

Huawei FT2050 Manual de usuario

Huawei

Huawei FP222A Manual de usuario

Huawei

Huawei EchoLife EG8240H5 Manual de usuario

Huawei

Huawei F316 Guía de instalación

Huawei

Huawei ETS2256 Manual de usuario

Huawei

Huawei ETS1220 Manual de usuario

Huawei

Huawei EP631S Manual de usuario

Huawei

Huawei EG8040 Series Manual de usuario

Huawei

Huawei HG8120 series Manual de usuario

Huawei

Huawei HG8120 series Manual de usuario

Huawei

Huawei ETS3023 Manual de usuario

Huawei

Huawei EP820-D04A Manual de usuario

Huawei

Huawei ETS3053 Manual de usuario

Huawei

Huawei ETS2059 Manual de usuario

Huawei

Huawei EchoLife HG8245 Especificaciones técnicas

Huawei

Huawei EchoLife HG8110 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario