Huawei FusionModule500 Manual de usuario
FusionModule500 Smart Mini Data Center
Quick Guide (02116410,
02116411, 02116412)
Huawei Technologies Co., Ltd.
Issue: 01
Date: 2021-07-15
2Copyright © Huawei Technologies Co., Ltd. 2021.
All rights reserved.
Item Specifications
Cabinet dimensions (H x
W x D)
Converged Cabinet: 2000 mm x 600 mm x 1100 mm
Installation scenario
Single
-cabinet scenario
Installation space
The cabinet provides 42 U available space. The mounting bars are
adjustable forward or backward, and space is reserved at the rear of
the cabinet for installing PDU2000s horizontally and vertically.
Power distribution
6 kVA UPS
PDU2000: can be installed horizontally or vertically.
IEC and GB
models are optional for horizontal installation.
Lithium battery: 100 Ah/48 V DC
Operating temperature
Indoor:
0°C to +40°C
Operating humidity
5%
–95% RH
IP rating
IP20
Installation mode
Installed on a concrete floor or an
ESD floor
Altitude
≤ 1000 m (
derated
when the altitude ranges from 1000 m to 4000 m)
1Overview
No. Component Onsite
Installation
(1) ECC800 Not
required
(2) Door status sensor Not
required
(3) Power distribution
subrack
Not
required
(4) UPS Not
required
(5) Lithium battery Required
(6) Water sensor Required
(7) Smoke detector Not
required
(8)
Temperature and
humidity (T/H)
sensor
Required
(9) PDU2000 Required
Cabinet Internal Layout (02116410)
3
The component layout is for reference only. The actual installation positions of the
components may vary.
If the IVS, server, and LAN switch are configured, determine their installation positions
based on the site requirements.
No. Component Onsite
Installation
(1) ECC800
Not required
(2)
Power
distribution
subrack
Not required
(3) UPS
Not required
(4)
Electronic clasp
lock
Not required
(5)
Lithium battery
Required
(6)
Integrated air
conditioner
Not required
(7) Water sensor Required
(8)
Smoke detector
Not required
(9) T/H sensor Required
(10) PDU2000 Required
No. Component Onsite
Installation
(1) ECC800
Not required
(2)
Power
distribution
subrack
Not required
(3) UPS
Not required
(4)
Electronic clasp
lock
Not required
(5)
Lithium battery
Required
(6) Transformer
Not required
(7) Integrated air
conditioner
Not required
(8) Water sensor Required
(9)
Smoke detector
Not required
(10) T/H sensor Required
(11) PDU2000 Required
Cabinet Internal Layout (02116412)
Cabinet Internal Layout (02116411)
(Front) (Rear)
4
Hardware Installation
1. Determine the cabinet position based on the
engineering layout diagram.
2. Place the cabinet at the correct installation position.
3. Level the cabinet using a wrench.
Use a measuring tape to check
that the vertical distance
between the top of the 2000
mm high cabinet and the floor
is 2000 mm (+3 mm). Then use
a level to check that the
cabinet is level.
Do not remove the anchor
bolts. Otherwise, you need to
rework them for use.
1. Remove the baffle plate from the smart cooling product.
2. Cut a cross in the middle of the rubber plug for the water pipe hole at the bottom of the
cabinet using an electrician's knife, and route the drainpipe.
3. Install the baffle plate for the smart cooling product.
1Installing the Cabinet
2Installing a Drainpipe for the Smart Cooling Product
5
For the 02116410 cabinet, install the
lithium battery at the 2 U or higher
position in the cabinet.
For the 02116411 cabinet, install the
lithium battery at the 11 U or higher
position in the cabinet.
For the 02116412 cabinet, install the
lithium battery at the 14 U or higher
position in the cabinet.
One lithium battery occupies 3 U space.
1. Push a lithium battery into the cabinet and
secure it.
3Installing Power Supply and Distribution Devices
3.1 Installing a Lithium Battery
3.2 Installing a PDU2000
Full-height Vertical PDU2000 Horizontal Non-intelligent PDU2000
Horizontal Intelligent PDU2000
6
For the 02116410 cabinet, one full-height vertical PDU2000 is installed in the left at the rear
of the cabinet.
For the 02116411 cabinet, two horizontal PDU2000s are installed. Intelligent PDU2000s and
non-intelligent PDU2000s are supported. Non-intelligent PDU2000s are installed at the 11 U
and 13 U positions at the rear of the cabinet. Intelligent PDU2000s are installed at the 10–
11 U and 12–13 U positions at the rear of the cabinet.
For the 02116412 cabinet, two horizontal non-intelligent PDU2000s are installed at the 16 U
and 18 U positions at the rear of the cabinet.
3.3 (Optional) Installing Busbars
If there is more than one
lithium battery, install
busbars.
For the 02116410 cabinet,
install the busbars at the 2
U and 3U positions in the
cabinet.
For the 02116411 cabinet,
install the busbars at the 17
U and 18 U positions in the
cabinet.
For the 02116412 cabinet,
install the busbars at the 20
U and 21 U positions in the
cabinet.
4Installing Monitoring Devices
4.1 Installing a SIM Card and Antenna
1. Remove the ECC800 main control module.
2. Install a SIM card. 3. Attach the antenna to the middle of
the cabinet top.
4. Connect the antenna cable.
7
4.2 Installing a PAD
1. (Optional) Remove the baffle plate from the front door of the Converged Cabinet.
2. (Optional) Install the PAD support fastener on the back of the front door of the Converged
Cabinet.
3. Adjust the PAD mounting support to match the dimensions of the PAD to be installed.
4. Remove the nuts from the PAD mounting support and install the support.
5. Route the PAD power cable through the cable hole in the PAD mounting support and
connect the cable to the PAD.
6. Adjust the feet on the top of the PAD mounting support and clamp the PAD to the PAD
mounting support.
7. Connect the ECC800 USB cable to the charging port on the PAD.
Adjusting screws
8
4.3 Installing T/H Sensors
The installation positions of the T/H sensors can be adjusted as required.
The default device address is 1.
Installing Remote T/H Sensors for the Smart Cooling Product
Installing T/H Sensors for the Cabinet
12
1. Place the water sensor on the floor under the cabinet.
2. Use an electrician's knife to cut a cross in the rubber plug for the cable hole at the bottom
of the cabinet.
3. Route the water sensor cable through the cable hole at the bottom of the cabinet, and
connect the cable to the water sensor cable connected to the ECC.
4.4 Installing an Electrode Water Sensor
1. Unpack the two T/H sensors, and attach one to the 33 U position on the right post of
the front door and the other to the 10 U position on the right post of the rear door of
the cabinet.
2. Set the DIP switch address of the T/H sensor on the front door to 2 and that of the
T/H sensor on the rear door to 1.
3. Insert the pre-routed cable into the port on the T/H sensor on the front door.
1. Unpack the two T/H sensors and attach them to the cabinet posts.
For the 02116410 cabinet, a T/H sensor is installed on the right post of the 39–41 U
position on the front door of the cabinet.
For the 02116411 or 02116412 cabinet, two T/H sensors are installed on the right post
of the 39 U position on the front door and 37 U position on the rear door of the cabinet.
2. Set the DIP switches on the T/H sensors.
For the 02116410 cabinet, set the DIP switch address of the T/H sensor on the front door
to 2.
For the 02116411 or 02116412 cabinet, set the DIP switch address of the T/H sensor on
the front door to 2 and that of the T/H sensor on the rear door to 1.
3. Insert the pre-routed cable into the port on the T/H sensor on the front door.
9
1.
1. Determine the installation position of the server and check whether floating nuts are
installed. If not, install them first.
4.5 (Optional) Installing a Server
2. Install guide rails. 3. Place the server on the guide rails
and push it in to the cabinet.
4. Secure the server.
It is recommended that the server be installed at the 33–34 U position of the cabinet. You can
adjust the position based on site requirements.
c. Use a hook-and-loop fastener to
secure the power cable.
5. Connect the power cable of the server.
a. Wear an ESD wrist strap or ESD gloves.
b. Connect one end of the power cable to
the cable port on the AC power module of
the server.
d. Route the power cable along the cable tray neatly, use cable ties to bind the power
cable, and use diagonal pliers to trim off the excess of the cable ties.
10
1. (Optional) Install an SD card. 2. Secure the camera to the mounting plate.
(1) Cable outlet
4.6 (Optional) Installing a Camera
3. Secure the mounting plate to the top
of the cabinet front door.
4. Adjust the camera.
5. Install the transparent cover.
Otros manuales para FusionModule500
7
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Almacenamiento de Huawei
Huawei
Huawei FusionDC1000A Manual de funcionamiento
Huawei
Huawei OceanStor S2600 Manual de instalación
Huawei
Huawei E3131s Guía de instalación
Huawei
Huawei FusionModule500 Manual de usuario
Huawei
Huawei FusionModule2000 V500R003C10 Especificaciones técnicas
Huawei
Huawei EG602 Manual de usuario
Huawei
Huawei FusionModule1000A40 ICT Solution Manual de usuario
Huawei
Huawei ES3000 V3 Manual de usuario
Huawei
Huawei FusionModule2000 V500R003C10 Manual de usuario
Huawei
Huawei EC301 Manual de usuario
Huawei
Huawei NetEngine 8000 M14 Manual de usuario
Huawei
Huawei FusionModule800 Manual de usuario
Huawei
Huawei LUNA2000-97KWH-1H1 Manual de usuario
Huawei
Huawei OceanStor 18000F V5 Series Manual de usuario
Huawei
Huawei N2000H V3 Manual de usuario
Huawei
Huawei Quidway S5000 Series Instrucciones de uso
Huawei
Huawei OceanStor S2600 Manual de usuario
Huawei
Huawei EC821 Manual de usuario
Huawei
Huawei E618 Manual de usuario
Huawei
Huawei EC321 Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario