Huawei NE20E-S2E Guía rápida

NE20E-S2E Configuration Help

1. New site or Expansion

This parameter is used for the NE20E-S to choose to purchase a new chassis or the

old chassis only expand LPU or upgrade software. If you want to purchase a new

NE20E-S , select "New site".If the software upgrade of the different version or the old

chassis only expand LPU, select "Expansion".

2. Please select the version

Please confirm the corresponding iManager version is correct when you select the

version:

NE20E-S2E V800R006C20: there is no corresponding iManager U2000 version can

support;

V800R007: the corresponding iManager U2000 version is V200R015C50 or later;

eSight version is V300R003C10 or later.

V800R008: the corresponding iManager U2000 version is V200R016C50 or later;

eSight version is V300R006C00 or later.

V800R009: the corresponding iManager U2000 version is V200R017C50 or later.

V800R010: the corresponding iManager U2000 version is V200R018C50 or later.

V800R011: the corresponding iManager U2000 version is V200R018C60 or later.

3. Please select the version that after upgrading

Please confirm the corresponding iManager version is correct when you select the

version:

NE20E-S2E V800R006C20: there is no corresponding iManager U2000 version can

support;

V800R007: the corresponding iManager U2000 version is V200R015C50 or later;

eSight version is V300R003C10 or later.

V800R008: the corresponding iManager U2000 version is V200R016C50 or later;

eSight version is V300R006C00 or later.

V800R009: the corresponding iManager U2000 version is V200R017C50 or later.

V800R010: the corresponding iManager U2000 version is V200R018C50 or later.

V800R011: the corresponding iManager U2000 version is V200R018C60 or later.

4. Need Basic Software CD or not

The basic software has been loaded on the equipment,and can be downloaded from

http://support.huawei.com.The CD is not delivered by default. If the CD is required by

customer,please choose 'YES'.

5. ===Basic Configuration===

o5.1 Please select the Portfolio Quotation of Basic Configuration

1. Basic Configuration includes Chassis,2*10GE-SFP+ and 24*GE-SFP fixed

interface, Dual Powers, Power cord/PGND cable, excludes Software Charge and

Document. Each chassis supports 2 subcard slots.

2. The DC basic configuration includes DC Power cord (3m/4mm^2) and PGND cable

(3m/6mm^2).

o5.2 Need DC PDU or not

1.Including DC PDU and PGND cable, without power cable(the length of power cable

is calculated automatically);2.The PDU of S2/S4/S8 could support 2 chassises. The

PDU of S16 could support 4 chassises. The quantity of power cable which connect

the PDU to PDF(Power Distribution Frame) is calculated with total chassises by

default.

6. ===High speed Card===

o6.1 4-Port 10GBase LAN/WAN-SFP+ Physical Interface Card

Specifications:

1)Support interface type:10GE LAN/WAN

2)Specifications list:

http://3ms.huawei.com/mm/docMaintain/mmMaintain.do?method=showMMDetail&f_i

d=CIP180525031314083

Optical transceiver limit:

1)This card support GE/10GE auto-sensing.

4-Port 10GBase

LAN/WAN-SFP+ Physical Interface Card

o6.2 2-Port 10GBase LAN/WAN-SFP+ Physical Interface Card(PIC)

This card support GE/10GE auto-sensing.

2-Port 10GBase

LAN/WAN-SFP+ Physical Interface Card

o6.3 1-Port 10GBase LAN/WAN-SFP+ + 8-Port 100/1000Base-X-SFP

Physical Interface Card

This card support GE/10GE auto-sensing.

1-Port 10GBase

LAN/WAN-SFP+ + 8-Port 100/1000Base-X-SFP Physical Interface Card

o6.4 10-Port 100/1000Base-X-SFP Physical Interface Card

10-Port

100/1000Base-X-SFP Physical Interface Card

o6.5 8-Port 100/1000Base-RJ45 Physical Interface Card(PIC)

It supports 1588v2 function.

8-Port

100/1000Base-RJ45 Physical Interface Card

7. ===Low speed Card===

o7.1 2-Port OC-3c/STM-1c (or 1-Port OC-12c/STM-4C) POS-SFP Physical

Interface Card

2-Port OC-3c/STM-

1c (or 1-Port OC-12c/STM-4C) POS-SFP Physical Interface Card

o7.2 1-Port Channelized STM-1c POS-SFP Physical Interface Card

1-Port Channelized STM-1c POS-SFP

Physical Interface Card

o7.3 4-Port Channelized STM-1c POS-SFP Physical Interface Card(PIC)

Need configure 155M SFP/eSFP Optical Transceiver.

4-Port Channelized

STM-1c POS-SFP Physical Interface Card(PIC)

o7.4 4-Port OC-3c/STM-1c POS-SFP Flexible Interface Card(PIC)

Need configure 155M SFP/eSFP Optical Transceiver.

4-Port OC-3c/STM-

1c POS-SFP Physical Interface Card

o7.5 32-Port E1 Physical Interface Card(PIC,120ohm)

Need configure E1 Cable

32-Port E1 Physical

Interface Card(120ohm)

o7.6 32-Port E1 Physical Interface Card(PIC,75ohm)

Need configure E1 Cable

32-Port E1 Physical

Interface Card(75ohm)

o7.7 16-Port E1 Physical Interface Card(PIC,120ohm)

Need configure E1 Cable

16-Port E1 Physical

Interface Card(120ohm)

o7.8 16-Port E1 Physical Interface Card(PIC,75ohm)

Need configure E1 Cable

16-Port E1 Physical

Interface Card(75ohm)

o7.9 4-Channel FXS/FXO+2-Channel E&M+2-Channel RS232+2-Channel

RS485 Board(MPA)

1. Two RS-485/RS-422 interfaces, based on the actual type of the peer device

prepare cables on site.

2. Two E&M interfaces, based on the actual type of the peer device prepare cables

on site.

3. Two RS-232 interfaces need to use a maximum of two RS-232 serial port cable.

4. 4-channel FXS/FXS interface need to use a maximum of four standard phone

lines.

o7.10 8-Channel V.35/X.21/V.24 Board(SA8)

The board supports 8-channel RS-232/X.21/V.24/V.35 interface.

o7.11 4 Channels C37.94 Optical Interface and 4 Channels CoDir64K

Electric Interface Board(MP8A)

You need to configure the SFP optical modules for Optical Interface and 120 ohm E1

cables for Electric Interface

o7.12 4 Channels GE/FE PoE Electrical Interface Board

The calbes should be done on site.

8. ===Multiplexing & Demultiplexing Card===

o8.1 8-Channel Multiplexing & Demultiplexing Card

1.This card does not need to configure Optical Transceiver.2.The port connected with

demultiplexing-port must configure CMDM Optical Transceiver.3.Multiplexing &

Demultiplexing Card contains 1-channel Multiplexing and 8-channel

Demultiplexing.Each channel need 2 PCS patch cords.

8-Channel

Multiplexing & Demultiplexing Card

9. ===10G/GE Auto-adaptation XFP SFP+ Optical Transceiver===

o9.1 XFP SFP+ Transceiver-SFP+-1310nm-10G/1G-Single-mode-LC-10km

Only below boards surpporting 10GE/GE auto-sensing optical transceiver:

03031DJP 4-Port 10GBase LAN/WAN-SFP+ Physical Interface Card

03031DJQ 1-Port 10GBase LAN/WAN-SFP+ + 8-Port 100/1000Base-X-SFP Physical

Interface Card

03030WGQ 2-Port 10GBase LAN/WAN-SFP+ Physical Interface Card

10. ===155M SFP/eSFP Optical Transceiver===

o10.1 Optical Transceiver,eSFP,1310nm,2.048Mb/s,LC,SM,2km

Need configure with MP8A board.

11. ===Patch Cord===

o11.1 Please select the Client Interface Option of Patch Cord

Default LC,10m.If need other specification,Please change it at "Bill of Configuration".

o11.2 Please input the quality of demultiplexing port of this equipment

1.This parameter is used for calculating the quantity of patch cords of demultiplexing-

port.Multiplexing & Demultiplexing Card contains 1-channel Multiplexing and 8-

channel Demultiplexing.Each channel need 2 PCS patch cords.

2.The port connected with demultiplexing-port must configure CMDM Optical

Transceiver.

12. ===Trunk Cable===

o12.1 Please select synchronous signal type

The device can supply Clock signal("2M primary clock")or 1588v2 signal("1PPS+TOD

signal" or "DCLS signal").If need Clock signal,please configure E1 cable.If need

1588v2 signal,made network cable on site.Any question ,please refer to Configuration

Manual or contact developer.

o12.2 Need to configure the synchronous signal input cable or not

Need to configure this cable, while need to input "2M Primary Clock".

o12.3 Need to configure the synchronous signal output cable or not

Need to configure this cable, while need to output "2M Primary Clock".

o12.4 ===RS232/FXS/FXO/E&M board cable===

▪12.4.1 Please input the quantity of RS232

MPA board supports RS232/RS485/RS422 interface, MPA board supports a

maximum of two RS232 cable, two RS485/RS422.

▪12.4.2 Please input the quantity of FXS/FXO

MPA board supports four FXS/FXO interface,MPA board needs a maximum of 4

standard phone lines.

▪12.4.3 Need E&M Interface or not

1. MPA board supports 2-channel E&M interface,MPA board supports a maximum of

2 pieces of E&M cable.

2. 6 Channels E&M Interface Board supports 6-channel E&M interface,and supports

a maximum of 6 pieces of E&M cable.

▪12.4.4 Need lightning arrester or not

Arrester must be configured when unshield cable is used in outdoor.

o12.5 ===SA8 board cable===

▪12.5.1 Please input the quantity of X.21-DTE

SA8 board supports 8-channel X.21 interface,SA8 board must be equipped with an 8

records at most X.21 DTE cable

▪12.5.2 Please input the quantity of X.21-DCE

SA8 board supports 8-channel X.21 interface,SA8 board must be equipped with an 8

records at most X.21 DCE cable

▪12.5.3 Please input the quantity of V.24-DTE

SA8 board supports 8-channel V.24 interface,SA8 board must be equipped with an 8

records at most V.24 DTE cable

▪12.5.4 Please input the quantity of V.24-DCE

SA8 board supports 8-channel V.24 interface,SA8 board must be equipped with an 8

records at most V.24 DCE cable

▪12.5.5 Please input the quantity of V.35-DTE

SA8 board supports 8-channel V.35 interface,SA8 board must be equipped with an 8

records at most V.35 DTE cable

▪12.5.6 Please input the quantity of V.35-DCE

SA8 board supports 8-channel V.35 interface,SA8 board must be equipped with an 8

records at most V.35 DCE cable

o12.6 Please input the quantity of MP8A board cable

MP8A board support SFP and RJ-45 interface,4 PCS fibre-Optical and 4PCS

120ohm 1*E1 cable can be configured at most for each MP8A.

13. ===Power Cable===

o13.1 Need separate configure DC power cable or not

1.No need configure by default. The basic configuration includes a 3m power cable.

Need configure separately only when the length of power cable is not

enough.2.Usually, the device needs configure separate power cable only when it

needs connect to the PDF directly.

o13.2 Please input the length of each device DC power cable (m)

By default, Huawei provides blue cables (-48V) and black cables (GND), and cables

of the other colors need to be remarked for purchase, and determine whether to

purchase locally according to the actual situation.

o13.3 Select the type of C13 power cable

1.PDU:Power Distribution Unit, the special main jack for the rack.

2.If the main jack in the rack is C13SF(as shown in figure), please select ""C13 PDU""

in the option ""Select the type of C13 power cable"", otherwise select ""ordinarily

C13"".

3.A matching AC power cable is provided only when the AC power module is

configured (or the device has the AC power module).

C13 PDU SF

Power Socket

PDU Cable C13-

C14

o13.4 Select the type of C13 AC power cable

Select the type of AC power cable carefully

Otros manuales de Enrutador de red de Huawei

Huawei

Huawei B683-74V Manual de usuario

Huawei

Huawei Quidway NetEngine80E Manual de usuario

Huawei

Huawei S6700 Series Guía

Huawei

Huawei NE20E-S8 Guía rápida

Huawei

Huawei AR550 Series Manual de usuario

Huawei

Huawei e5180s Manual de usuario

Huawei

Huawei AR2200-S Series Manual de usuario

Huawei

Huawei Quidway NetEngine40E Guía

Huawei

Huawei Quidway S9300 Manual de usuario

Huawei

Huawei AR Series Manual de funcionamiento

Huawei

Huawei AR120 Series Especificaciones técnicas

Huawei

Huawei H122-373 Manual de usuario

Huawei

Huawei Aolynk VDR824 Manual de usuario

Huawei

Huawei SUN2000-M5 Series Manual de usuario

Huawei

Huawei Quidway S1700-8-AC Manual de usuario

Huawei

Huawei AR532 Manual de usuario

Huawei

Huawei EG8147X6 Manual de usuario

Huawei

Huawei EG8147X6 Manual de programación

Huawei

Huawei OptiXstar EG8145X6 Manual de usuario

Huawei

Huawei B525 Manual de usuario

Huawei

Huawei LTE CPE B593 Manual de usuario

Huawei

Huawei WiFi Cube 2 4G Manual de usuario

Huawei

Huawei Vodafone AR1220 Manual de usuario

Huawei

Huawei quidway s7700 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad