Huawei NE05E Manual de usuario

HUAWEI TECHNOLOGIES CO., LTD.

NE05E&NE08E Series

Quick Installation Guide(19inch&21inch cabinet)

Issue: 05

Date: 2020-08-31

No part of this document may be reproduced or transmitted in any form or by any

means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of

their respective holders.

Notice

The purchased products, services and features are stipulated by the contract made

between Huawei and the customer. All or part of the products, services and features

described in this document may not be within the purchase scope or the usage scope.

Unless otherwise specified in the contract, all statements, information, and

recommendations in this document are provided "AS IS" without warranties, guarantees

or representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has

been made in the preparation of this document to ensure accuracy of the contents, but

all statements, information, and recommendations in this document do not constitute a

warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: https://www.huawei.com

Email: su[email protected]

Installation Flow

Precautions

This document provides simple and distinctive guidelines for quick hardware installation of the

NE05E&NE08E(NE05E-SR/S2/SE/SF/SG/SH/SI/SQ&NE08E-S6/S6E/S9).

Based on the height of a device, the NE05E-SR/S2/SE/SF/SG/SH/SI/SQ are considered 1 U

devices, and the NE08E-S6/S6E are considered 2 U devices, and the NE08E-S9 are considered 3

U devices. 1 U = 44.45 mm (1.75 in.)

As the installation methods are similar, the fixed NE05E-SI is used as an example for the 1 U

device, and the card-inserted NE08E-S6 is used as an example for the 2 U device. The

installation differences are specially described in this document.

This document does not describe pre-delivery assembly. This document only describes

procedures for onsite installation.

Wear ESD gloves or Antistatic Wrist Strap prior to

contact with the equipment or before handling the

plug-boards, boards, and IC chips to prevent

damage to sensitive components caused by

electrostatic discharge from the human body.

Binding intervals between cable ties or optical fiber binding straps inside the cabinet

cannot exceed 250 mm.

Electrostatic Discharge

Pre-Installation Check

Verify that the equipment room, power supply, ground cables and optical cables are ready

for installation. Start the installation according to the engineering design documents after

confirming that conditions are met. Refer to the

Installation Guide

for information about

specific operational requirements and technical specifications.

NOTE

CAUTION

Bundling cables

Tape Measure Philips Screwdriver

(M2-M6) Flathead Screwdriver

(M2-M6)

Adjustable Wrench

Level Bar

Ratchet Crimp

Tool Cable Cutter

Wire Stripper

Network Cable

Crimping Pliers Diagonal Pliers

Sharp-nose Pliers

Bayonet Wrench

Paper Knife

Marker Pen

Electric Iron

Heat Gun Multimeter

ESD Gloves

Binding Strap Insulation Tape

Antistatic Wrist

Strap

Punching Wire pliers

Vacuum cleaner

Tools for Installation

Cord end

terminal crimper

Cable Tester Optical Power

Meter

BER Tester

Coax Stripper

NE05E-S2

Introduction to the 1U-height Chassis

Clock interface

Power supply

interface

Time interface

NM interface

(Console interface)

Alarm interface

FE/GE electrical interface

10GE optical interface

FE/GE optical interface

E1 interface

Alarm interface

Power supply

interface

GE optical interface

Clock and time interface

T1 interface

Antistatic jack interface

FE/GE electrical interface SHDSL interface

NE05E-SE/NE05E-SF

NM interface

(Console interface)

FE/GE optical

interface

PGND point

NE05E-SG/NE05E-SH/NE05E-SI/NE05E-SQ

Clock interface

Power supply interface

Time interface

NM interface

(Console interface)

Electrical interface

GE optical interface

Alarm interface

E1 interface

FE/GE optical

interface

FE/GE optical interface FE/GE electrical interface

Power supply interface Clock interface

10GE optical interface

Antistatic jack interface

Time interface

NM interface

(Console interface)

Alarm interface

For running an AC NE05E-SQ, you must turn on the switches of both AC power modules

operating in 1+1 backup mode.

NOTE

PGND point

NE08E-S6

Introduction to the 2U-height Chassis

Alarm interface

Power supply interface

GE optical interface

Clock interface

Time interface

Antistatic jack interface

E1 interface

NM interface

(Console interface)

Electrical interface

NE08E-S6E

Alarm interface

Power supply interface

GE optical interface

Clock interface

Time interface

Antistatic jack interface NM interface

(Console interface)

Electrical interface

10GE optical interface

PGND point

NE08E-S9(DC)

Introduction to the 3U-height Chassis

Alarm interface PGND point

Power supply interface

GE optical interface

Clock interface

Time interface

Antistatic jack interface

E1 interface

NM interface

(Console interface)

Electrical interface

NE08E-S9(AC)

Alarm interface PGND point

Power supply interface

optical interface

Clock interface

Time interface

Antistatic jack interface NM interface

(Console interface)

710

aInstalling the floating nut

Installing the Chassis

bInstalling the chassis in the cabinet

Floating nuts

When fixing the floating nuts, keep a distance of at

least 50 mm on both the left and right sides of the NE

device for proper ventilation.

Installation holes for the floating nut: The three

holes with even spacing equal a 1-U height.

A 1 U device corresponds to holes 1-3, and a 2 U

device corresponds to holes 1-6.

2.0±0.2 N·M

•Install the chassis and align the installation holes of the mounting ears with the floating nuts,

and fasten the two captive screws clockwise.

•Each 2U device requires only one cable tray, which must be installed on the right of the device

(front view).

•If you deploy an NE in the same cabinet as another device, reserve a distance of 1 U or higher

between the two devices for heat dissipation.

Cable guiding

frame

Scenario I: Installing the Chassis in the 19-inch Cabinet

Mount bar

(Use a Flathead Screwdriver if

no mount bar is available)

Otros manuales para NE05E

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Huawei

Huawei

Huawei 5G CPE Pro H112-372 Manual de usuario

Huawei

Huawei HG530 Manual de usuario

Huawei

Huawei ADSL2+Broadband Router Aolynk DR814 Manual de usuario

Huawei

Huawei Soyealink B628-350 Manual de usuario

Huawei

Huawei H122-372 Manual de usuario

Huawei

Huawei Quidway NetEngine80E Manual de usuario

Huawei

Huawei AR1200 Series Manual de usuario

Huawei

Huawei B315 LTE CPE Manual de usuario

Huawei

Huawei V200R001C01 Instrucciones de funcionamiento

Huawei

Huawei Quidway NetEngine80E Manual de usuario

Huawei

Huawei B310 Manual de usuario

Huawei

Huawei Aolynk VDR824 Manual de usuario

Huawei

Huawei EG8143A5 Manual de usuario

Huawei

Huawei E5180s-22 Especificaciones técnicas

Huawei

Huawei E5180 Manual de usuario

Huawei

Huawei Baudcom EG8145V5 Manual de usuario

Huawei

Huawei quidway s7700 Manual de usuario

Huawei

Huawei HG232f Manual de usuario

Huawei

Huawei AR530 Series Manual de usuario

Huawei

Huawei ATN 910C-K Manual de usuario

Huawei

Huawei B311-520 Manual de usuario

Huawei

Huawei HG531s V1 Manual de usuario

Huawei

Huawei EchoLife EG8245H5 Manual de usuario

Huawei

Huawei AR530 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad