Huawei SmartAX MA5800-X7 Manual de usuario

HUAWEI TECHNOLOGIES CO., LTD.

SmartAX MA5800-X7

Quick Installation Guide

Issue: 04

Date: 2016-08-24

Intended Audience

About This Document

Change History

Symbol Conventions

This document describes how to install the MA5800-X7.

The intended audience is hardware installation engineers.

Updates between document issues are cumulative. Therefore, the latest document issue

contains all updates made in previous issues.

The symbols that may be found in this document are defined as follows.

Symbol Description

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in equipment damage, data loss, performance deterioration, or

unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury,

equipment damage, and environment deterioration.

Updates in Issue 01 (2015-04-30)

This is the first release.

Updates in Issue 02 (2015-07-28)

Based on issue 01 (2015-04-30), added 4.2 Installing the service subrack in an IEC cabinet.

Updates in Issue 03 (2016-03-31)

Based on issue 02 (2015-07-28), added the requirements on third-party cabinets that accommodate

the MA5800-X7, and optimized the layout of the document.

Updates in Issue 04 (2016-08-24)

Based on issue 03 (2016-03-31), added 7.2 Cabinet with Routed Cables (AC).

Conten t

1 Precautions …………………………………..…………………………............................………….1

2 Tools and Meters………………………….………………………….............................…………….2

3 Appearance and Structure……………………………………….............................…………….3

4 Environment Requirements on Third-Party Cabinets ………………….………4

5 Space Requirements on Third-Party Cabinets ……………….………..…......5

5.1 When the Cabinet Accommodates One MA5800-X7 Subrack………….………….5

5.2 When the Cabinet Accommodates One MA5800-X7 Subrack and Another Device....6

6 Installing the Service Subrack……………….……………………...............................………...7

6.1 Installing the Service Subrack in an ETSI Cabinet............................................................7

6.2 Installing the Service Subrack in an IEC Cabinet..............................................................8

7 Routing Cables……………………………….……………………...............................………..9

7.1 Cabinet with Routed Cables (DC)...........................................................................9

7.2 Cabinet with Routed Cables (AC).........................................................................10

7.3 Routing PGND Cable and Power Cables.......................................................................11

7.4 Routing Clock Cables………….......................................................................................12

7.5 Routing Network Cable..……….……..............................................................................13

7.6 Routing Trunk Cables………...........................................................................................14

7.7 Routing Optical Fibers (P2P Board)…............................................................................15

7.8 Routing Optical Fibers (PON Board)...............................................................................16

7.9 Routing Optical Fibers (Upstream)............................................................................17

8 Post-Installation Check…………………………………………………...............................…...18

9 Power-on Check…………………………………………………………..............................….......19

1 Precautions

•After routing the cable, attach the label or fasten the tag to the cable 20 mm away from the

connector.

•After the label for the signal cable is attached to the signal cable, the rectangular text area of

the label must face rightwards or downwards.

•After the identification plate for the power cable is attached to the power cable, the text area of

the plate must face rightwards or upwards. Ensure that the side attached with the label faces

outwards.

ESD gloves ESD wrist strap

Affixing labels / tags

•This document aims to provide simple and distinctive guidelines for hardware installation.

•This document does not describe operations for the pre-delivery installation. Instead, this

document describers only the operations for on-site installation.

Electrostatic Discharge

Before touching the device, or holding the boards and IC chips, wear the ESD gloves or the

ESD wrist strap to prevent the electrostatic discharge of the human body from damaging the

sensitive components. Ensure that the other end of the ESD wrist strap is properly grounded.

•The distance between cable ties or binding straps inside the cabinet must be within 250 mm.

(For user cable, the distance must be within 200 mm.)

•Use a diagonal pliers to cut off the extra part of the cable tie to the end, and ensure that the

cable tie is neat without sharp edges to prevent hand injury.

Bundling cables

2 Tools and Meters

ESD gloves ESD wrist strap

Optical power meterMultimeter

Network cable

crimping pliers Network cable tester

Before you begin, get the following tools ready.

Marker Flat-head screwdriver Phillips screwdriver Diagonal pliers

Optical fiber

cleaner

Optical fiber

microscope

3 Appearance and Structure

The MA5800-X7 service subrack is 6 U high, and has a fan tray at the right. The subrack is

installed in the cabinet through the ETSI or IEC mounting ears.

Fan tray

Universal interface board

Service board

Power board

Grounding point

Control board

Mounting ear

Cable Manager

ESD jack

535.0

242.2 268.7

287.8

442.0

263.9

482.6

242.2 268.7

287.8

442.0

263.9

With IEC (19 inch) mounting ear With ETSI (21 inch) mounting ear

Unit: mm Unit: mm

4 Environment Requirements on Third-Party Cabinets

•Cabinet dustproof requirement: The MA5800-X7 subrack is not dustproof, so select

dustproof cabinets that support dust filter maintenance.

•Cabinet installation requirements:

For the MA5800-X7, select an IEC60297-compliant cabinet with a depth of 300 mm or more

so that a space with a depth of 55 mm or more can be reserved for cable/fiber routing after

boards are installed.

When the MA5800-X7 is installed in an ETSI-compliant cabinet that meets the related

requirements, replace the mounting ears with the ETSI-compliant mounting ears customized

by Huawei for the MA5800-X7.

•Cabinet door requirement: When devices are operating, keep the cabinet door closed.

•Grounding requirement: Huawei cabinets are grounded through mounting bars. Ensure that

third-party cabinets are properly grounded based on site conditions.

•Power distribution requirements: Ensure that an over-current protection mechanism has

been deployed on the upper-level device. A 40-A over-current protection mechanism is

recommended for the MA5800-X7. Ensure that the circuit breaker trip value of the upper-level

device is greater than or equal to the rated value on the device nameplate.

•Heat dissipation requirements:

The fan tray of the MA5800-X7 dissipates heat from the left to the right in air blowing. When

being installed on multiple open racks in parallel, do not install the device supporting air

blowing on the neighboring rack to avoid serial ventilation.

Ensure that the cabinet has an air inlet and the hole density of the cabinet door is 60% or

higher.

When a cabinet accommodates multiple subracks or the device shares a cabinet with other

active devices, ensure that the following space requirements are met.

Front view Side view

Airflow blocking object

•The MA5800-X7 supports left-in right-out heat dissipation, so the cabinet must have an

unblocked air inlet on its door.

•You are advised to reserve more than 4 U space above and under the MA5800-X7

respectively to minimize the impact on other components in the cabinet.

5 Space Requirements on Third-Party Cabinets

5.1 When the Cabinet Accommodates One MA5800-X7 Subrack

Without an air deflector With an air deflector

Front view Side view Front view Side view

10U

If the MA5800-X7 subrack is installed in a subrack with B-T airflow, you are advised to add

an air deflector to the subrack so that the hot air does not direct flow to the MA5800-X7.

When 2 U space is reserved at the air inlet and 3 U space is reserved at the air outlet, the

cabinet panels will have less impact on the heat dissipation of the MA5800-X7.

Active device

Air

deflector

(3 U)

•Reserve 10 U space between the devices or add a 3 U air deflector to redirect air flows to

minimize the mutual heat dissipation impacts on the devices.

•Reserve at least 4 U space when you route fibers or install other passive devices to facilitate

subsequent air inlet or dust filter cleaning.

5.2 When the Cabinet Accommodates One MA5800-X7 Subrack and

Another Device

5 Space Requirements on Third-Party Cabinets

6 Installing the Service Subrack

Remove IEC mounting ears

•The MA5800-X7 service subrack is configured with IEC (19-inch) mounting ears by default.

The MA5800-X7 subrack can be mounted in an IEC cabinet or rack. To install the MA5800-X7

subrack in an ETSI cabinet, uninstall the IEC mounting ears, and then install the ETSI (21-

inch) mounting ears.

•Before installing the service subrack, it is advised to install cable managers or sliding rails in

the cabinet or rack for supporting the service subrack.

Install the lower cable manager

Install the service subrack

and upper cable manager

Locate the installation

positions of the cable

manager and service subrack

on the mounting bars, and

install captive nuts at these

positions. Captive nut

Mounting bar (use a flat-

head screwdriver if no

mounting bar is available.)

Phillips screwdriver

Lower cable manager

Upper cable manager

Service subrack

Cable manager（between

mounting ear and service subrack）

Install ETSI mounting ears

6.1 Installing the Service Subrack in an ETSI Cabinet

Tabla de contenidos

Otros manuales de Hardware de red de Huawei

Huawei

Huawei EchoLife EG8143H5 Manual de usuario

Huawei

Huawei CR-P1RS Manual de usuario

Huawei

Huawei ME906J Instrucciones de instalación

Huawei

Huawei SmartLi Manual de usuario

Huawei

Huawei OptiX OSN 8800 Guía

Huawei

Huawei BBU3900 V300 Manual de usuario

Huawei

Huawei FusionServer Pro CH225 V5 Guía de referencia rápida

Huawei

Huawei RT-FIC-1AE3 Manual de usuario

Huawei

Huawei CR-R1UL Manual de usuario

Huawei

Huawei CR52-MPUA Manual de usuario

Huawei

Huawei MatePad Paper Manual de usuario

Huawei

Huawei CR52-MPUA Manual de usuario

Huawei

Huawei RT-1CPOS Manual de usuario

Huawei

Huawei eSight V200R003C00 Manual

Huawei

Huawei RT-FIC-1GBE Manual de usuario

Huawei

Huawei CR52-10GE Manual de usuario

Huawei

Huawei FusionModule2000 V500R003C10 Especificaciones técnicas

Huawei

Huawei OptiXstar V183 Manual de usuario

Huawei

Huawei SUN2000 Series Manual de usuario

Huawei

Huawei Airbridge BTS3606C Especificaciones técnicas

Huawei

Huawei OptiXstar P612E Manual de usuario

Huawei

Huawei BTS3900 GSM Manual de usuario

Huawei

Huawei RRU3804 Manual de usuario

Huawei

Huawei F01T100 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario