Huawei Optix OSN 810 Manual de usuario
1
Safety Information
Optix OSN 810
Quick Installation Guide
Issue: 03
Date: 2016-10-20
CAUTION
Following All Safety Precautions
Before any operation, read the instructions and precautions in this document carefully to minimize the possibility
of accidents. The Danger, Caution, and Note items in the documents do not cover all the safety precautions that
must be followed. They only provide the generic safety precautions for operations. When operating Huawei
products and equipment, you must comply with safety precautions and special safety instructions related to
corresponding equipment provided by Huawei. The safety precautions in the document are related to only
Huawei products. Huawei is not liable for any consequence that results from the violation of universal
regulations for safety operations and safety codes on design, production, and equipment use.
Complying with the Local Safety Regulations
When operating the device, comply with the local safety regulations.
Qualified Personnel Only
The personnel in charge of installation and maintenance must be trained and master the correct operating
methods and safety precautions before beginning work.
Symbols
■
Indicates a potentially hazardous situation, which if not avoided, could result in
equipment damage, data loss, performance degradation, or unexpected results.
Provides additional information to emphasize or supplement important points of the
main text.
NOTE
■
■
■
Safety of Personnel
When handling optical fibers, do not stand close to, or look into the optical fiber outlet with unaided eyes.
Protect yourself when drilling holes. Flying dust may hurt your eyes or you may inhale the dust.
When working at a height, be cautious about falling objects.
■
2016
Installation Process
Start
End
Chassis outline
Page3
Installing Chassis
Page3-15
Checking the
Installation
Page21-22
Installing Fibers
and Cables
Page16-20
Appendix
Page23-31
Labels
Page31-32
2
Wire stripper
Marker
Level Phillips screwdriverFlat-head screwdriver
Measuring tape
Installation Tools
Adjustable wrench
[aperture ≥ 32 mm (1.26 in.)]
Protective gloves
Claw hammer
Wrench
Hammer drill Φ8 drill bit
Hex key [4 mm (0.16 in.)]
Diagonal pliers
MultimeterFiber binding tape
3
1 Chassis Appearance
Installing Chassis
2 Installing Chassis
conversion bracket
Cabling cavity
70mm
90mm
400mm
300mm
Top
Clearance for a Single OSN 810 in Standard Mode Clearance for a Single OSN 810 in Side-Mounted Mode
Recommended Clearances
Minimum Clearances
Recommended Clearances
Minimum Clearances
4
2 Installing Chassis
Installing the OSN 810 on a Pole
a
Install the OSN 810 mounting brackets
Verify that the arrows on the mounting
brackets are pointing up.
Adjust the position of the nut and remove
one end of the square-neck bolt from the slot
on the auxiliary bracket.
Slide the mounting brackets onto the pole
horizontally and insert the square-neck bolt
into the slot.
Use a 16 mm (0.63 in.) M10 torque wrench to
tighten the nuts to 40 N·m (354.03 lbf·in.) so that
the mounting brackets are secured onto the pole.
Tighten the nuts on the two square-neck
bolts alternatively. After the main and
auxiliary brackets are secured properly,
measure the spacing between the
brackets on both sides and ensure that
the spacing is the same on the two sides.
NOTE
(1) auxiliary bracket (2) square-neck bolt
1
2
Shown in the figure above, it is recommended that the mounting kits be
installed at a position 1200 mm (47.24 in.) to 1600 mm (59.06 in.) high
above the ground.
NOTE
5
2 Installing Chassis
Installing the OSN 810 on a Pole
a
Use an M6 inner hexagon screwdriver to remove
the four inner hexagon screws from the mounting
brackets, and remove the main bracket from the
auxiliary bracket.
Remove the conversion bracket from the rear side of the OSN 810 to the side of the OSN 810.
(1) Main bracket
(2) Pole installation bracket
Install the Chassis with RRUs
b
Install the OSN 810 onto the main bracket,use an inner hexagon torque screwdriver to tighten the captive screw into the
holes on the top of the conversion bracket and main bracket to 5 N·m (44.25 lbf·in.) so that the conversion bracket and
main bracket are firmly secured.
(1) conversion bracket
2
1
(2) Main bracket
6
2 Installing Chassis
Install the Chassis with RRUs
b
Install the main bracket, and install the OSN 810 on the main bracket. Then use an inner hexagon torque screwdriver to
tighten the captive screw into the connection holes on the top of the conversion bracket and main bracket for the OSN 810,
with a torque of 5 N·m (44.25 lbf·in.).
Install the metal sheet for fixing the RRUs and
OSN 810.
(1) Screw
(2) Metal sheet
Insert the removed screw into the hole on the top of
the neighboring RRU and use an M6 torque
screwdriver to tighten the screw to 5 N·m .
Use an M6 Phillips screwdriver to loosen the
screw on the metal sheet farther from the
handle of the OSN 810 and remove the screw.
Use an M6 Phillips screwdriver to loosen the screw
on the metal sheet closer to handle of the OSN 810.
Then rotate the metal sheet to align the vacant hole
in the metal sheet with a hole on the top of the
neighboringRRU.
NOTE
The OptiX OSN 810 can be installed on the right or left side of an RRU. Ensure that the front side of the OptiX OSN
810 faces outwards and the cabling cavity can be opened.
Cabling cavity
Main bracket
7
Installing the OSN 810 on U-steel
c
•As shown in the figure above, it is recommended that the mounting kits be installed at a position 1200 mm (47.24
in.) to 1600 mm (59.06 in.) high above the ground.
•For details about how to install the chassis on U-steel, see the procedure for mounting the chassis on a pole.
Installing the OSN 810 on Angle Steel
d
•As shown in the figure above, it is recommended that the mounting kits be installed at a position 1200 mm (47.24
in.) to 1600 mm (59.06 in.) high above the ground.
•For details about how to install the chassis on angle steel, see the procedure for mounting the chassis on a pole.
2 Installing Chassis
NOTE
NOTE
8
Installing the OSN 810 on a Wall
e
2 Installing Chassis
Disassemble the OSN 810 mounting brackets.
(1) Main bracket (2) Square-neck bolt (3) Pole installation bracket
(4) Auxiliary bracket (5) Flat washer (6) Spring washer
(7) Nut (8) Plastic cap
Use an M6 inner hexagon torque screwdriver to remove the four inner hexagon screws on the pole installation bracket,
and remove the main bracket from the pole installation bracket.
Use an M10 torque wrench to loosen the nuts on the two square-neck bolts, and remove the plastic cap, nuts, spring
washers, flat washers, square-neck bolts, and pole installation bracket from the auxiliary bracket.
Place the pole installation bracket against the installation position, use a level to verify that the pole installation bracket is
placed horizontally, and then mark anchor points with a marker.
(1) Level
(2) Pole installation bracket
(3) OSN 810
9
Installing the OSN 810 on a Wall
e
2 Installing Chassis
Drill holes at the anchor points, and then insert expansion anchor bolt assemblies.
Use a hammer drill with a Ф12 bit to drill holes vertically at the marked anchor points with the depth ranging from 55
mm (2.17 in.) to 60 mm (2.36 in.), use a vacuum cleaner to clear the dust out from inside and around the holes, and
measure the distances between holes. If any of the hole is beyond the acceptable range, mark a new anchor point
and drill a new hole.
Tighten the expansion anchor bolts slightly and place one vertically into each hole.
Use a rubber mallet to pound the expansion anchor bolt until it goes all the way into the hole.
Tighten and then loosen the expansion bolt, and remove the M10 bolt, spring washer, and flat washer in sequence.
Install the pole installation bracket on the expansion anchor bolts, place the flat washers, spring washers, and nuts
through the expansion anchor bolts in sequence, and then use a 16 mm (0.63 in.) torque socket to tighten the nuts to 30
N·m (265.52 lbf·in.).
Verify that the arrows on the pole installation
bracket are pointing up.
(1) M10x80 bolt
(2) Nut
(3) Spring washer
(4) Flat washer
(5) Expansion tube
10
Installing the OSN 810 on a Wall
e
2 Installing Chassis
Install the main bracket onto the pole installation bracket, and use an inner hexagon screwdriver to tighten four M6x16
inner hexagon screws to 5 N·m (44.25 lbf·in.) so that the main bracket and pole installation bracket are firmly secured.
Install the OSN 810 onto the main bracket,use an inner hexagon torque screwdriver to tighten the captive screw into the
holes on the top of the conversion bracket and main bracket to 5 N·m (44.25 lbf·in.) so that the conversion bracket and
main bracket are firmly secured.
(1) Main bracket
(2) Pole installation bracket
Tabla de contenidos
Otros manuales de Hardware de red de Huawei
Huawei
Huawei USG6000E Series Manual de usuario
Huawei
Huawei OptiX OSN 3500 Instrucciones de uso
Huawei
Huawei EMUA Series Manual de usuario
Huawei
Huawei CR-P4CF Manual de usuario
Huawei
Huawei RT-FIC-16ASE Manual de usuario
Huawei
Huawei RT-1CPOS Manual de usuario
Huawei
Huawei OptiX RTN 910A Manual de usuario
Huawei
Huawei EN83CTLA Manual de usuario
Huawei
Huawei FTK01 Manual de usuario
Huawei
Huawei CR52-SFUA Manual de usuario
Huawei
Huawei RTN510 Manual de usuario
Huawei
Huawei CR52-10GE Manual de usuario
Huawei
Huawei SUN2000-15KTL-50KTL Series Manual de usuario
Huawei
Huawei FusionServer Pro CH121 V5 V100R005 Manual
Huawei
Huawei LSBM1P4G8B0 Manual de usuario
Huawei
Huawei MAP05A1 Manual de usuario
Huawei
Huawei CR52K-2xPOS/STM64 Manual de usuario
Huawei
Huawei RTN XMC ODU V200 Manual de usuario
Huawei
Huawei ETP4860-B1A2 Manual de usuario
Huawei
Huawei FusionModule 500 Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
