Huawei EG162 Manual de usuario

No part of this manual may be reproduced or transmitted in any form or by any means

without prior written consent of Huawei Technologies Co., Ltd.

Trademarks

and HUAWEI are trademarks of Huawei Technologies Co., Ltd. All other

trademarks mentioned in this manual are the property of their respective holders.

Notice The information in this manual is subject to change without notice. Every effort has been

made in the preparation of this manual to ensure accuracy of the contents, but all

statements, information, and recommendations in this manual do not constitute the

warranty of any kind, expressed or implied.

Table of Contents

Getting to Know the EG162....................................................................................1

Requirements for the PC..........................................................................................1

Preparing the EG162 ...............................................................................................2

Installation Guide.....................................................................................................2

Safety Information...................................................................................................4

Thank you for purchasing Huawei EG162

USB Stick (hereinafter referred to as the

EG162).

Note:

yThis manual briefs the profiles of EG162,

including the preparation,

installation/uninstall process, and safety

precautions.

yYou are highly recommended to read the

manual before using the EG162.

yThe actual signal strength and the

transmission rate are affected by the

environment. If the singal stength is weak

when you use the USB Stick, you can move

the PC, or use the delivery-attached data

cable move the USB Stick.

Getting to Know the EG162

This is a sketch for EG162. The actual product

may differ.

1. USB connector

Connects to the USB interface of the PC.

2. SIM card slot

Fixes and bear the SIM card.

3. Indicator

It indicates the status of the EG162.

yGreen, blinking twice every 3s: The EG162

is powered on.

yGreen, blinking twice every 3s: The EG162

is registered to a GSM/GPRS/EDGE

network.

yGreen, always on: The GSM/GPRS/EDGE

connection is set up.

yBlue, always on: SIM card is not installed.

SIM card is invalid. PIN code is required.

yBlue, blinking twice every 3s: The EG162

fails to search the network.

yOff: The EG162 is offline or removed from

a laptop.

Requirements for the PC

Before using the EG162, configure the

computer according to the following

requirements.

yUSB interface: USB 2.0 full speed

yCPU: 866 MHz Pentium or above

yMemory: 128 MB or above

yFree space on the hard disk: 100 MB or

above

yOperating system: Windows XP, Windows

2000 or Window Vista

yScreen resolution: 1024 × 768 is

recommended.

Note:

yImproper configurations may degrade the

wireless device performance. Make sure that

the computer configurations meet the

requirements.

yFor Windows XP, it is recommended to

install patches such as Service Pack 2 or

above.

yFor Windows 2000, it is recommended to

install patches such as Service Pack 4 or

above.

Preparing the EG162

1. Press the right and left side of the cover,

and Remove it, take out the SIM card

slot.

2. Insert the SIM card into the card slot,

with the contact area on the card is facing

down and the beveled corner on the card

is facing inwards. Make sure that the

SIM card is fully in place.

3. Insert the card slot with the SIM card

into the EG162.

Installation Guide

The procedure for installing the management

program is subject to the operating system

installed on your laptop. The following section

takes Windows XP as an example.

Installing the EG162

1. Connect the EG162 to the USB interface

of the computer..

2. The driver runs automatically.

The Welcome interface is displayed.

Note:

yIf the driver does not run automatically,

double-click My Computer. Then

double-click Mobile Partner CD-ROM

to install the driver. Alternatively, open

My Computer > Mobile Partner. Then

double-click Autorun.exe to install it.

yIf there is more than one language, the

Installer Language interface is

displayed.

Select a language and click OK.

3. Click Next.

The License Agreement interface is

displayed.

4. Read the license agreement carefully. If

you agree with the license agreement,

select I agree….

The Choose Install Location interface is

displayed.

5. Choose the install directory and click

Next.

The Choose Start Menu Folder

interface is displayed.

6. Choose or create the start menu folder

and click Install.

Mobile Partner is installed.

7. Click Finish to complete the installation.

Launching the Mobile Partner

After the EG162 is installed, Mobile Partner is

launched automatically. Then every time the

EG162 is connected to the PC, the Mobile

Partner is launched automatically.

You can double-click the shortcut icon of

Mobile Partner to launch it.

Uninstalling the Mobile Partner

1. Click Start Menu.

2. Click Control Panel.

3. Find the management program, and click

ll it.

Add/Remove Program to uninsta

Note: It is recommended to restart the

computer after the uninstall to ensure

that Mobile Partner is completely

cleared.

Removing the EG162

rtner.

1. Log out of Mobile Pa

2. Remove the EG162.

Safety Information

Please read the safety information carefully to

ensure the correct and safe use of your

wireless device.

General Recommendations for Use

Always handle your wireless device with care

and keep it in a clean and dust-free place. Do

not expose your wireless device to open

flames or lit tobacco products.

yAlways keep your wireless device dry.

yDo not drop, throw or try to bend your

wireless device.

yDo not paint or scratch your wireless device.

yDo not attempt to disassemble your wireless

device. Doing so will void warranty. Only

authorized personnel are allowed to do so.

yThis product requires a minimum distance

of 1.5 cm from the body when in operation.

yKeep your wireless device in normal

temperature. Your wireless device can only

operate between -5ºC and +55 ºC.

yUse approved accessories only. Do not

connect your wireless device to any

incompatible products.

Obey Laws and Regulations

Do not operate your wireless device where it

may be unsafe to do so or where you are

required not to do so.

To deactivate your wireless device, close all

applications using the wireless device first and

then remove the wireless device from your

PC.

Obey all local laws, regulations, rules, orders,

signs and notices while using the wireless

device. Signs about the use of mobile phones

should also be obeyed as referring to other

wireless equipment including wireless

devices.

Deactivate in Explosive Areas

Deactivate your wireless device where the air

is potentially explosive. It is rare, but your PC

could generate sparks.

Deactivate in Blasting Areas

Deactivate your wireless device where

blasting is in progress. Remote-controlled RF

devices are often used at construction sites to

set off blasting.

Deactivate in Aircrafts

Deactivate your wireless device before

boarding or in any aircraft. Wireless devices

can cause interference in aircrafts.

Deactivate at Hospitals

Obey regulations or rules at hospitals.

Deactivate your wireless device near medical

equipment. Wireless devices can cause

interference to cardiac pacemakers, implanted

defibrillators or other medical equipment.

Deactivate near Hearing Devices

Deactivate your wireless device near hearing

devices. People with hearing aids may

experience interfering noises near wireless

devices.

Recommendations for Children

Do NOT allow children to play with your

wireless device. They could hurt themselves

or others, or could accidentally damage the

wireless device. Your wireless device contains

small parts with sharp edges that may cause an

injury or a choking hazard.

Deactivate While Driving

Do not use the wireless device while driving.

Immunity to Interference

Your wireless device is immune to

interferences caused by audible signals.

Cleaning and Maintenance

yBefore you clean or maintain the wireless

device, close all applications using wireless

device and remove your wireless device

from your PC.

yClean your wireless device with a piece of

soft antistatic cloth.

yIf the wireless device or any of its

accessories does not work, turn to an

authorized service center for help.

Environmental Protection

Observe the local regulations regarding the

disposal of your packaging materials, old

wireless device and its accessories. Please

promote their recycling.

SIM/USIM Cards

While inserting or removing the SIM card,

protect yourself against electrostatic discharge

(ESD). Do not touch the connector of the SIM

card. As a precaution, always make sure that

the wireless device is already in your hand

before you insert or remove the SIM card.

Restart on ESDs

Software will attempt to re-initialize a

connection once a substantial electrostatic

discharge causes the device to reset. If the

software is not operational after an ESD,

restart the modem software application.

Agency/Regulatory Information

The wireless device is approved for use in

many regions of the world. In these regions,

the device meets all radio frequency exposure

requirements. The following approvals and

notices apply in specific regions as noted.

CE Approval (European Union)

The wireless device is approved to be used in

the member states of the EU. Huawei declares

that the wireless device is in compliance with

the essential requirements and other relevant

provisions of the Radio and

Telecommunications Terminal Equipment

Directive 1999/5/EC (R&TTE Directive).

Radio Frequency Exposure

To ensure compliance at all times with the

R&TTE Directive* 1999/5/EC, the wireless

device can be held in the hand but still

requires a minimum distance of 1.5 cm from

the body when in operation. For body-worn

use, it must be suitably mounted so that it is at

least 1.5 cm away from the body. Mounting

accessories (for example, belt clips) cannot be

made of metal. Do not put the wireless device

in your pocket.

* The general public RF exposure limits

referenced in the R&TTE Directive are

consistent with the published Guidelines of

the International Commission on

Non-Ionizing Radiation Protection (ICNIRP)

1998. ICNIRP is a formally recognized

non-governmental organization in

Non-Ionising Radiation Protection for the

World Health Organisation (WHO), the

International Labour Organisation (ILO) and

the European Union (EU). For more

information, visit the ICNIRP website at

www.icnirp.de.

Certification Information (SAR)

THIS DEVICE MEETS THE

GOVERNMENT'S REQUIREMENTS FOR

EXPOSURE TO RADIO FREQUENCY

ELECTROMAGNETIC FIELD.

Your wireless device is a low-power radio

transmitter and receiver. When it is running, it

emits low levels of radio frequency energy

(also known as radio waves or radio frequency

fields).

Governments around the world have adopted

comprehensive international safety guidelines,

developed by scientific organizations, e.g.

ICNIRP (International Commission on

Non-Ionizing Radiation Protection) and IEEE

(Institute of Electrical and Electronics

Engineers Inc.), through periodic and

thorough evaluation of scientific studies.

These guidelines establish permitted levels of

radio wave exposure for the public. The levels

include a safety margin designed to assure the

safety of all persons, regardless of age and

health, and to account for any variations in

measurements.

Specific Absorption Rate (SAR) is the unit of

measurement for the amount of radio

frequency energy absorbed by the body when

using a wireless device. The SAR value is

determined at the highest certified power level

in laboratory conditions, but the actual SAR

level of the wireless device while operating

can be well below the value. This is because

the wireless device is designed to use the

minimum power required to reach the

network.

All models of Huawei’s wireless device are

designed to meet radio frequency exposure

guidelines such as European Council

Recommendation and Federal

Communications Commission Notice (United

States).

European Council Recommendation:

Before a wireless device model is available

for sale to the public, it must be tested

according to the technical standard-EN 50361

and not exceed the limit established by the

European Council Recommendation:

1999/519/EC for safe exposure.

The SAR limit adopted by the 1999/519/EC is

2.0 watts/kilogram (W/kg) averaged over ten

gram of tissue. The highest SAR value for this

device type when tested is 0.927 W/kg.

[EN 50361 scope states “This basic standard

applies to any electromagnetic field (EM)

transmitting devices intended to be used with

the radiating part of the equipment in close

proximity to the human ear including mobile

phones, cordless phones, etc. The frequency

range is 300 MHz to 3 GHz. Therefore, the

above text does not address primary use of the

wireless device product.]

Federal Communications Commission

Notice (United States): Before a wireless

device model is available for sale to the public,

it must be tested and certified to the FCC that

it does not exceed the limit established by the

government-adopted requirement for safe

exposure.

The SAR limit adopted by the USA and

Canada is 1.6 watts/kilogram (W/kg) averaged

over one gram of tissue. The highest SAR

value reported to the FCC and IC for this

device type when tested for use is 1.28 W/kg.

[There is no reference to the specific reference

standard or its applicability to the intended use

of the product]

FCC Statement

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the

equipment and receiver.

yConnect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

yConsult the dealer or an experienced

radio/TV technician for help.

This device complies with Part 15 of the FCC

Rules and with RSS-210 of Industry Canada.

Operation is subject to the following two

conditions: (1) this device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

Warning: Changes or modifications made to

this equipment not expressly approved by

HUAWEI may void the FCC authorization to

operate this equipment.

Version: V100R001_01

Part Number: 31018383

Tabla de contenidos

Otros manuales de Módem de Huawei

Huawei

Huawei Mobile Internet Key Manual de usuario

Huawei

Huawei E220 Manual de instrucciones

Huawei

Huawei 51071SMK Manual de usuario

Huawei

Huawei Broadband E219 Manual de usuario

Huawei

Huawei B2368 Manual de usuario

Huawei

Huawei E3372 Manual de instrucciones

Huawei

Huawei M3710 Manual de usuario

Huawei

Huawei E3272 Manual de instrucciones

Huawei

Huawei Mobile Broadband Manual de usuario

Huawei

Huawei E3531S-3 Guía de solución de problemas

Huawei

Huawei EC5805 Manual de usuario

Huawei

Huawei E1756A Manual de usuario

Huawei

Huawei D105 Manual de usuario

Huawei

Huawei E173S-1 Manual de usuario

Huawei

Huawei Mobile Broadband USB Stick Manual de usuario

Huawei

Huawei E587 Especificaciones técnicas

Huawei

Huawei Maxis E5832 Manual de usuario

Huawei

Huawei E2010 Instrucciones de montaje

Huawei

Huawei E368 Manual de usuario

Huawei

Huawei E585 Manual de usuario

Huawei

Huawei EchoLife HG8240 Manual de usuario

Huawei

Huawei U.S.Cellular UML397 Manual de usuario

Huawei

Huawei E1691 Manual de usuario

Huawei

Huawei EC156 Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario