Huawei MERC-1100W-P Manual de usuario

HUAWEI DIGITAL POWER TECHNOLOGIES CO., LTD.

MERC-(1300W, 1100W)-P Smart PV Optimizer

Quick Guide

Issue: 03

Part Number: 31500HND

Date: 2022-11-30

Type II apparatus

(enhanced insulation)

Burn warning

Electric shock

warning

EU waste electrical and electronic

equipment (WEEE) mark

Refer to

documentation

1. The Smart PV Optimizer is a DC-DC converter installed on the rear of PV modules in a PV

system. It manages the maximum power point (MPP) of each PV module to improve the

energy yield of the PV system, and performs functions such as module-level shutdown and

module-level management.

2. An optimizer is delivered with two types of input power cables: long (1300 mm) or short

(100 mm) cables. For PV modules with long cables, select optimizers with short cables; for PV

modules with short cables, select optimizers with long cables.

1Product Overview

Short Input Power Cables Long Input Power Cables

2Installing the Device

Installation Requirements

2.1

Clearance

PV modules

Mounting

bracket

PV modules

3. Improper installation and operations of optimizers

may cause fire. Do not store flammable or

explosive materials in the installation area.

4. Do not cut the cables delivered with

the optimizers. Otherwise, the

warranty will be voided.

5. Avoid direct sunlight.

2. Do not install optimizers in positions

that may be submerged in water.

Water

Cable

cutter

Ventilation area

Rooftop (color steel tile)

1. If optimizers and PV modules are installed close to the rooftop (for example, color steel tile

rooftop), ensure that the optimizers are well ventilated. It is recommended that the ambient

temperature be less than or equal to 70℃. If the ambient temperature exceeds 70℃, the

optimizers may shut down for overtemperature protection. After the operating temperature

decreases, the optimizer automatically recovers with no risk of damage.

Properly plan the installation position of optimizers to ensure that the cables between the optimizer

and the PV module and between adjacent optimizers can be properly connected, and the maximum

communication distance between the optimizer and the solar inverter is within 350 m.

Note: Use a

marker to mark

information on the

physical layout

template if needed.

Installing the Optimizer

2.2

Solar inverter

1. Select optimizers based on the installation scenario.

•For PV modules with long power cables, select optimizers with short input power cables. The

PV modules can be installed vertically or horizontally.

•For PV modules with short power cables, select optimizers with long input power cables. The

PV modules can be installed only vertically.

2. After determining the installation position of the optimizer, remove the SN label from the

optimizer and attach it to the physical layout template. For details, see instructions on the

back of the physical layout template.

Flange nut

Installed on an Extruded Aluminum

Profile –T-shaped Bolt

M8x20 T-shaped bolt

Extruded

aluminum

profile

The optimizer is mounted to an

aluminum profile on the front or rear

side with T-shaped bolt and nut.

The T-shaped bolt and nut need to be

purchased separately from Huawei.

The bolt dimensions are as follows.

Installed on a PV Module

Frame –Bolt Assembly

M8x20 bolt assembly

Flange nut

Before installation, ensure that a

mounting hole has been reserved

on the PV module frame.

The bolt assembly and nut need to

be purchased from a third party.

Ensure that the length meets the

installation requirements of the PV

module frame.

PV module

3. Install the optimizer based on the selected installation mode.

Installed on a PV Module

Frame –Frame Mounting Bracket

Do not press the optimizer mounting

bracket against the positioning pole

of the frame mounting bracket.

Purchase the frame mounting

bracket separately from Huawei.

Install the PV module after the

optimizer is installed.

PV module

Frame mounting bracket

3Installing the Optimizer Cables

1. Connect the optimizer

input (IN) cable to

the PV module

connection box.

2. Connect the positive probe of the multimeter to the positive

output terminal of the optimizer and the negative probe to the

negative output terminal. Check the output voltage of a single

optimizer.

Ensure that the input (IN) and output (OUT) cables of the optimizer are correctly connected. If

they are reversely connected, the device may be damaged.

The typical value

of V1 is 1 V.

Voltage

Cause

Suggestion

0.95 V ≤ V1 ≤ 1.05 V

The optimizer is normal.

> 1.05 V

The

optimizer is faulty.

Replace

the optimizer.

V1 < 0.95 V

The irradiance is low.

The optimizer input

power cables are not

connected.

The optimizer cables

are incorrectly

connected.

The optimizer is faulty.

1. Measure the voltage when the irradiance is

adequate.

Connect the optimizer input power cables.

Correct the optimizer cable connections.

Connect the optimizer input power cables

to the PV module output power cables.

If the voltage is still abnormal, replace the

optimizer.

V1 ≈

–1 V

The probes are reversely

connected.

Reconnect the positive and negative probes

correctly.

3. Check that the optimizer and its input cables are properly connected, and then connect the

optimizer output power cables. Measure the PV string voltage when the sunlight is sufficient.

Configuration Scenarios

PV string

To minimize electromagnetic interference,

ensure that the distance between the positive

and negative cables of an optimizer is

minimized.

To ensure reliable communication between the

inverter and optimizers, the AC and DC power

cables of the inverter must be more than 10 cm

away from the AC power cables of motor-type

impact loads, such as air conditioners and

elevators. It is recommended that the cables be

routed in different troughs or pipes.

For details about how to configure PV strings

with optimizers connected to the inverter, see

section 2.3 "Configuration Principles" in the

user manual. Incorrect configurations may

cause serious consequences.

Note: The figure shows only the output

(OUT) cables.

Voltage

Cause

Suggestion

The

PV string

voltage is 0.

The PV string is open-circuited.



The cables are not connected to the

same PV string.

Check whether the PV string is open-

circuited.

Identify the string cables correctly.

The PV string

voltage is a

negative value.

The probes are reversely connected.

The cable labels are incorrect.

Reconnect the positive and negative

probes correctly.

Prepare cable labels correctly.

The value of PV

string voltage

is less than the

number of

optimizers.



Some optimizer input power cables

are not connected.

Some optimizer output power

cables are not connected.

Some optimizer output power

cables are reversely connected.

Check whether PV modules and PV

string cables are correctly connected.

The value of PV

string voltage

is greater than

the number of

optimizers.

The actual number of optimizers in

the string is greater than expected.

PV modules are directly connected

to PV strings without being

connected to optimizers.

Check whether the number of

optimizers in the PV string is correct.

Check whether PV modules and PV

string cables are correctly connected.

4. Connect cables between the PV string and the solar inverter.

4Power-On Commissioning

1. The physical layout of the optimizers must be provided so that you can easily

locate faulty optimizers based on the physical layout diagram.

2. The physical layout of the optimizers must be provided to use the optimizer

disconnection detection function. After optimizer disconnection detection is

performed, the locating result can be viewed on the Layout screen.

3. Choose Maintenance > Subdevice management > Auto search to add an

optimizer. For details about the physical layout of optimizers, see the

MERC

Smart PV Optimizer User Manual

FusionSolar App Quick Guide

. You can

scan the QR code to obtain the

FusionSolar App Quick Guide

If changes occur in the system, such as adding, deleting, and replacing an optimizer, adjusting

the physical position of an optimizer, or adjusting the PV string connected to the solar inverter

input, turn off the DC and AC switches of the inverter and wait for 5 minutes before performing

the operation to avoid personal injuries. After the change is performed, the optimizer search

process must be performed again and the physical layout diagram must be updated. Otherwise,

the networking is incomplete, optimizer faults cannot be located, or the system fails.

1. Open the FusionSolar app, log in to intl.fusionsolar.huawei.com using the installer account,

choose Me > Device commissioning, and connect to the WLAN hotspot of the solar inverter.

2. Select installer and enter the login password. Tap Log In. The device commissioning screen is

displayed.

3. Choose Device monitoring, select the PV string and check the optimizer status.

5Troubleshooting

Optimizer status

Status

Description

Green

The optimizer is running properly.

Gray

The optimizer is offline.

Check that the SN and

location information are correct and search for the

device again.

Red

The optimizer is faulty.

Yellow

The optimizer is disconnected.

Alarm

Cause

Suggestion

Input overvoltage

Optimizer input

overvoltage

occurred.

Check whether the open

-circuit voltage of the PV module

exceeds the maximum input voltage of the optimizer.

Overtemperature

protection

The optimizer

internal

temperature is too

high.

Check the ventilation and ambient temperature at the

optimizer installation position. If the ventilation is poor

or the ambient temperature exceeds the upper

threshold, improve the ventilation and heat dissipation.

2. If the ventilation and ambient temperature are normal,

contact your installer.

Internal

hardware fault

An internal fault

occurred in an

optimizer.

Contact your installer.

Output terminal

overtemperature

The output

terminal

temperature of

some optimizers is

abnormal.

Contact your installer to replace the faulty optimizer and

the optimizer connected to the short output

cables of the

faulty optimizer.

Output backfeed

Optimizer output

backfeed occurred.

1. Check whether PV modules are shaded when PV

strings are connected in parallel.

2. If the fault persists, contact your installer.

Abnormal output

voltage

The optimizer

output voltage is

abnormal.

1. When the irradiance is normal, perform optimizer

search again.

2. Check the voltage of the corresponding PV string. If

the voltage is greater than 0 V, power off the system

and check whether the extension cable of the

abnormal optimizer is correctly connected.

3. Check the voltage of the corresponding PV string. If

the voltage is 0 V, power off the system and check the

cable connection of the PV string. If there is an open

circuit, rectify the cable connection of the PV string. If

the polarity is incorrect, reconnect the PV string in the

correct polarity. After the open circuit or reverse

polarity is rectified, power on the system and perform

an optimizer search again. If the alarm persists, check

whether the extension cable of the abnormal

optimizer is correctly connected.

4. If the fault persists, contact your installer.

Note: The polarity at both ends of the extension cable

must be opposite (one end is a positive connector, and

the other is a negative connector). To determine the PV

string polarity, see "3 Installing the Optimizer Cables."

Upgrade failed

The optimizer

software upgrade

failed.

1. When the irradiance is normal, perform the optimizer

upgrade again.

2. If the fault persists, contact your installer.

6Replacing an Optimizer

1. Power off the solar inverter and remove the faulty optimizer.

2. Install a new optimizer and correctly connect its cables.

3. Power on the solar inverter. Log in to the FusionSolar app and tap the plant name on the

Home screen to access the plant screen. Choose Devices > Inverter, select the inverter

corresponding to the faulty optimizer, tap Optimizer Search, and perform operations as

prompted to search for optimizers.

4. Choose Devices > Connected devices > Optimizer, tap Optimizer No., select the faulty

optimizer, tap Device Replacement, and replace the optimizer as prompted.

If

optimizers need to be replaced, perform the preceding procedure for

times.

After the optimizer is replaced, the new optimizer automatically inherits the energy yield,

physical layout, and logical layout of the faulty optimizer.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de Huawei

Huawei

Huawei SUN2000 M5 Series Manual de usuario

Huawei

Huawei SUN2000-100KTL-M2 Manual de usuario

Huawei

Huawei SUN2000-90KTL Manual de usuario

Huawei

Huawei SUN2000-43KTL-IN-C1 Manual de usuario

Huawei

Huawei FusionSolar SUN2000 Manual de usuario

Huawei

Huawei SUN2000 Series Manual de usuario

Huawei

Huawei SUN2000-50KTL-M0 Manual de usuario

Huawei

Huawei SUN2000-8KTL Manual de usuario

Huawei

Huawei Iris Hellas SUN2000 Series Manual de usuario

Huawei

Huawei SUN2000-3KTL-10KTL-M0 Manual de usuario

Huawei

Huawei SUN2000-75KTL Series Manual de usuario

Huawei

Huawei SUN3KTL-L1 Manual de usuario

Huawei

Huawei SUN2000 3,6KTL-L1 Manual de usuario

Huawei

Huawei SUN2000-5KTL-L1 Manual de usuario

Huawei

Huawei SUN2000-375W-USP0 Manual de usuario

Huawei

Huawei SUN2000-111KTL-NHM0 Manual de usuario

Huawei

Huawei SUN2000-33KTL-A Manual de usuario

Huawei

Huawei SUN2000-8KTL Manual de usuario

Huawei

Huawei SUN2000-M2 Manual de usuario

Huawei

Huawei UPS5000-H-400K-FT Manual de usuario

Huawei

Huawei SUN2000 Series Manual de usuario

Huawei

Huawei SUN2000-4.6KTL-L1 Manual de usuario

Huawei

Huawei SUN2000-100KTL Manual de usuario

Huawei

Huawei SUN2000-2KTL-L1 Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario