Huawei HG630 V2 Manual de usuario

HG630 V2 Home Gateway

Quick Start

1 Connecting Cables

Installing the HG630 V2 on a DSL Broadband Network

In some communities, Internet service providers use telephone lines to provide

broadband access services.

If you have subscribed to digital subscriber line (DSL) broadband, you can connect

the HG630 V2 to a telephone port for Internet access.

Follow the steps in the following figure to connect devices properly.

1 Telephone wall jack 2 Splitter 3 Telephone

When configuring the HG630 V2 for the first time, use an Ethernet cable to

connect the HG630 V2 to a computer

2 Powering On

To power on the HG630 V2, press its power button.

After the HG630 V2 is powered on, the HG630 V2 indicator turns on. The following

table lists how the indicators behave when the HG630 V2 is operating correctly. If the

indicators do not behave as expected, ensure that everything is plugged in correctly.

4 HG630 V2 5 Power adapter 6 Desktop computer

7 Set-top Box 8 Laptop computer 9 Smart Phone

10 Pad

a LINE port b PHONE port c MODEM port

Indicator Expected State Description

Power Steady on The HG630 V2 is powered on.

WAN Steady on A digital subscriber line (DSL) connection

has been set up and activated.

Blinking A DSL connection is being activated.

Internet

Steady on

The HG630 V2 is connected to the Internet

in router mode, but no data is being

transmitted.

Blinking

The HG630 V2 is connected to the Internet

in router mode, and data is being

transmitted.

WLAN

Steady on The HG630 V2 has WLAN enabled, but is

not transmitting data.

Blinking The HG630 V2 has WLAN enabled, and

data is being transmitted.

WPS

Steady on

The HG630 V2 is connected to a wireless

client, such as a computer with a wireless

network adapter, over the WLAN using the

Wi-Fi Protected Setup (WPS) function.

The WPS indicator is steady on for 300

seconds.

Blinking

The HG630 V2 is attempting to connect to a

wireless client over the WLAN using the

WPS function.

LAN1 ～LAN4

Steady on

The LAN port is connected to an Ethernet

device (such as a computer) with a network

cable, but no data is being transmitted.

Blinking

The LAN port is connected to an Ethernet

device with a network cable, and data is

being transmitted.

USB

Steady on The HG630 V2 is connected to a USB

device, but no data is being transmitted.

Blinking The HG630 V2 is connected to a USB

device, and data is being transmitted.

Indicator Expected State Description

3 Setting the Computer IP Address

Before logging in to the HG630 V2 web management page, set the IP address of the

computer that will be used for the login.

On Windows 7

1. Click in the lower right corner of your desktop. Choose Open Network

and Sharing Center.

2. Choose Change adapter settings. Right-click Local Area Connection

and choose Properties.

3. Double-click Internet Protocol Version 4 (TCP/IPv4).

4. Select Obtain an IP address automatically and Obtain DNS server

address automatically. Click OK.

4 Setting Network Access Parameters

Configuring an Automatical Connection to Access the

Internet

The HG630 V2 supports you to choose the proper connection mode automatically to

access the Internet, meaning you do not need to install dial-up software or perform

dial-up operations on your computer and just following the wizard page.

To set up an automatical connection to access the Internet:

1. Open a browser on your computer. In the address box, enter 192.168.1.1.

Press Enter to access the web management page.

2. On the login page, enter the login user name (user by default) and

password (HuaweiUser by default). Click Log in.

> To protect against unauthorized access, change the user name and

password after the first login.

> You can change the account parameters on Maintain > Account

Management page.

3. On the I want to... page, click Start Wizard.

4. On the I want to...Connect to the Internet page, choose Connect

automatically, and click Next.

The HG630 V2 supports DSL uplink mode, meaning you can use the

HG630 V2 with a telephone port for Internet access.

After you complete the preceding settings, check the status of the Internet indicator

light. When the Internet indicator light turns steady green, you can start browsing the

Internet.

You need to perform the preceding operations on a computer once only. The next

time you power on your computer, you can browse the Internet without performing

the same configurations.

Configuring a Wireless Account

After you complete the preceding settings, click Set Up WLAN, you will see the I

want to Set Up WLAN page used to configure the wireless account.

The default SSID and WLAN Key printed on the HG630 V2's rear panel are

unique and secure. If you do not want to change them, just turn the WLAN

switch on.

For security reasons or to make the password easy to remember, you can change

the wireless network name and password as follows:

1. On the I want to Set Up WLAN page, switch on the 2.4 GHz WLAN

network.

2. Enter your desired SSID (WLAN name) and WLAN password.

3. Click Save.

5 Wireless Connection Setup

The wireless configuration software provided by Windows is used as an example to

describe how to set up a wireless connection.

On Windows 7

1. Click in the lower right corner of your desktop.

2. From the wireless network list, select the WLAN provided by the HG630

V2. Click Connect.

3. In the displayed dialog box, enter the WLAN password and click OK.

4. In the wireless network list, check the WLAN connection status. If the

status is Connected, the computer is wirelessly connected to the HG630

V2.

6 Safety information

This section contains important information about the operation of your device. It also

contains information about how to use the device safely. Read this information

carefully before using your device.

Electronic device

Do not use your device if using the device is prohibited. Do not use the device if doing

so causes danger or interference with other electronic devices.

Interference with medical equipment

> Follow rules and regulations set forth by hospitals and health care facilities.

Do not use your device where prohibited.

> Some wireless devices may affect the performance of hearing aids or

pacemakers. Consult your service provider for more information.

> Pacemaker manufacturers recommend that a minimum distance of 15 cm

be maintained between a device and a pacemaker to prevent potential

96723331_01

interference with the pacemaker. If using a pacemaker, hold the device on

the side opposite the pacemaker and do not carry the device in your front

pocket.

Areas with flammables and explosives

> Do not use the device where flammables or explosives are stored (in a gas

station, oil depot, or chemical plant, for example). Using your device in

these environments increases the risk of explosion or fire. In addition,

follow the instructions indicated in text or symbols.

> Do not store or transport the device in containers with flammable liquids,

gases, or explosives.

Operating environment

> Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the

device in these environments may result in circuit malfunctions.

> Before connecting and disconnecting cables, stop using the device and

disconnect it from the power supply. Ensure that your hands are dry during

operation.

> Place the device on a stable surface.

> Keep the device away from electronic appliances that generate strong

magnetic or electric fields, such as a microwave oven or refrigerator.

> During thunderstorms, power off your device and remove all cables

connected to it to protect against lightning strikes.

> Do not use your device during thunderstorms to protect your device against

any danger caused by lightning.

> Ideal operating temperatures are 0 °C to 40 °C. Extreme heat or cold may

damage your device or accessories.

> Keep the device and accessories in a well-ventilated and cool area away

from direct sunlight. Do not enclose or cover your device with towels or

other objects. Do not place the device in a container with poor heat

dissipation, such as a box or bag.

> To protect your device or accessories from fire or electrical shock hazards,

avoid rain and moisture.

> Keep the device away from sources of heat and fire, such as a heater,

microwave oven, stove, water heater, radiator, or candle.

> Do not place any object, such as a candle or a water container, on the

device. If any foreign object or liquid enters the device, immediately stop

using it, power it off, and remove all cables connected to it. Then, contact an

authorized service center.

> Observe local laws and regulations, and respect the privacy and legal rights

of others.

> Do not block device openings. Reserve a minimum of 10 cm around the

device to dissipate heat.

> Stop using your device or applications for a while if the device is

overheated. If skin is exposed to an overheated device for an extended

period, low temperature burn symptoms, such as red spots and darker

pigmentation, may occur.

> Do not touch the device's antenna. Otherwise, communication quality may

be reduced.

> Do not allow children or pets to bite or suck the device or accessories.

Doing so may result in damage or explosion.

> The device should be installed and operated with a minimum distance of 20

cm between the radiator and your body.

> Keep the device in a place with good reception. The distance between the

device and other metal materials (such as metal brackets or metal doors

and windows) should be greater than 25 cm and the distance between the

device should be greater than 30 cm.

Child's safety

> Comply with all precautions with regard to child's safety. Letting children

play with the device or its accessories may be dangerous. The device

includes detachable parts that may present a choking hazard. Keep away

from children.

Accessories

> Using an unapproved or incompatible power adapter, charger or battery

may cause fire, explosion or other hazards.

> Choose only accessories approved for use with this model by the device

manufacturer. The use of any other types of accessories may void the

warranty, may violate local regulations and laws, and may be dangerous.

Please contact your retailer for information about the availability of

approved accessories in your area.

Power adapter safety

> The power plug is intended to serve as a disconnect device.

> For pluggable devices, the socket-outlet shall be installed near the devices

and shall be easily accessible.

> Unplug the power adapter from electrical outlets and the device when not in

use.

> Do not drop or cause an impact to the power adapter. If it is damaged, take

it to an authorized service center for inspection.

> If the power cable is damaged (for example, the cord is exposed or broken),

or the plug loosens, stop using it at once. Continued use may lead to

electric shocks, short circuits, or fire.

> Do not touch the power cord with wet hands or pull the power cord to

disconnect the power adapter.

> Do not touch the device or the power adapter with wet hands. Doing so may

lead to short circuits, malfunctions, or electric shocks.

> If your power adapter has been exposed to water, other liquids, or

excessive moisture, take it to an authorized service center for inspection.

> Ensure that the power adapter meets the requirements of Clause 2.5 in

IEC60950-1/EN60950-1/UL60950-1 and has been tested and approved

according to national or local standards.

Cleaning and maintenance

> During storage, transportation, and operation of the device, keep it dry and

protect it from collision.

> Keep the device and accessories dry. Do not attempt to dry it with an

external heat source, such as a microwave oven or hair dryer.

> Do not expose your device or accessories to extreme heat or cold. These

environments may interfere with proper function and may lead to fire or

explosion.

> Avoid collision, which may lead to device malfunctions, overheating, fire, or

explosion.

> If the device is not going to be used for an extended period of time, power it

off, and remove all cables connected to it.

> If anything unusual occurs (for example, if the device emits smoke or any

unusual sound or smell), immediately stop using it, power it off, remove all

cables connected to it, and contact an authorized service center.

> Do not trample, pull, or excessively bend any cable. Doing so may damage

the cable, causing the device to malfunction.

> Before you clean or maintain the device, stop using it, stop all applications,

and disconnect all cables connected to it.

> Do not use any chemical detergent, powder, or other chemical agents (such

as alcohol and benzene) to clean the device or accessories. These

substances may cause damage to parts or present a fire hazard. Use a

clean, soft, and dry cloth to clean the device and accessories.

> Do not place magnetic stripe cards, such as credit cards and phone cards,

near the device for extended periods of time. Otherwise the magnetic stripe

cards may be damaged.

> Do not dismantle or remanufacture the device and its accessories. This

voids the warranty and releases the manufacturer from liability for damage.

In case of damage, contact an authorized service center for assistance or

repair.

Disposal and recycling information

This symbol (with or without a solid bar) on the device, batteries (if

included), and/or the packaging, indicates that the device and its

electrical accessories (for example, a headset, adapter, or cable) and

batteries should not be disposed of as household garbage. These

items should not be disposed of as unsorted municipal waste and

should be taken to a certified collection point for recycling or proper

disposal.

For more detailed information about device or battery recycling,

contact your local city office, household waste disposal service, or retail store.

Disposal of the device and batteries (if included) is subject to WEEE Directive Recast

(Directive 2012/19/EU) and Battery Directive (Directive 2006/66/EC). The purpose of

separating WEEE and batteries from other waste is to minimize the potential

environmental impacts and human health risk of any hazardous substances that may

be present.

Reduction of hazardous substances

This device is compliant with the REACH Regulation [Regulation (EC) No 1907/

2006] and RoHS Directive Recast (Directive 2011/65/EU). Batteries (if included) are

compliant with the Battery Directive (Directive 2006/66/EC). For up-to-date

information about REACH and RoHS compliance, please visit the web site http://

consumer.huawei.com/certification.

Tabla de contenidos

Otros manuales de Puerta de Huawei

Huawei

Huawei AR515 Series Manual de usuario

Huawei

Huawei DAU eA680 Manual de usuario

Huawei

Huawei HG532D Manual de usuario

Huawei

Huawei HG659B Manual de usuario

Huawei

Huawei EchoLife HG556a Manual

Huawei

Huawei HG532t Manual de usuario

Huawei

Huawei HG630B Manual de usuario

Huawei

Huawei EchoLife HG520s Manual de usuario

Huawei

Huawei B890 Manual de usuario

Huawei

Huawei EchoLife HG556 Manual de usuario

Huawei

Huawei HG256s Manual de usuario

Huawei

Huawei HG552e Manual de usuario

Huawei

Huawei B222s Manual de usuario

Huawei

Huawei HG630B Manual de usuario

Huawei

Huawei USG6310 Manual de usuario

Huawei

Huawei U-SYS IAD101H Manual de usuario

Huawei

Huawei HG552e Manual de usuario

Huawei

Huawei HG530 Manual de usuario

Huawei

Huawei Echolife HG520b Manual de usuario

Huawei

Huawei HG610 Manual de usuario

Huawei

Huawei DG8245V Manual de usuario

Huawei

Huawei B315s-608 Manual de usuario

Huawei

Huawei OptiXstar B650G-8E8P3W Manual de usuario

Huawei

Huawei HG655a Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario

RTA

RTA 460MCBC-N2E Hoja de especificaciones