HSD ViperJET Manual de usuario
ViperJET
75mm EDF
CAUTION:All instructions and warnings must be followed exactly.
Mishandling of Li-Po batteries can result in a fire,personal injury,
and/or property damage.
• By handling,charging or using the included Li-Po battery,you assume all
risks associated with lithium batteries.
•If, at any time, the battery begins to balloon or swell, discontinue use
immediately. If charging or discharging, discontinue and disconnect.
Continuing to use, charge or discharge a battery that is ballooning or
swelling can result in a fire.
• Always store the battery at room temperature in a dry area for best results.
• Always transport or temporarily store the battery in a temperature range of
40-120º F(5-49º C).Do not store battery or aircraft in a car or direct sun-
light.If stored in a hot car,the battery can catch fire or be damaged.
• Always charge batteries away from flammable materials.
• Always inspect the battery before charging and never charge dead or dam-
aged batteries.
• Always disconnect the battery after charging,and let the charger cool
between charges.
• Always consistently monitor the temperature of the battery pack while
charging.
• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO
BATTERIES.Failure to charge the battery with a compatible charger
may cause fire, resulting in personal injury and/or property damage.
• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
• Never leave charging batteries unattended.
• Never charge batteries over recommended levels.
• Never attempt to dismantle or alter the charger.
• Never allow minors under the age of 14 to charge battery packs.
•Never charge batteries in extremely hot or cold places(recommended
temperature is 40-120°F or 5-49°C)or place in direct sunlight.
Charging Warnings
Meaning of Special Language:
The following terms are used throughout the product manual to indicate various levels of potential harm when operating this product:
NOTICE: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
CAUTION: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
WARNING: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
WARNING: Read this instruction manual entirely to become thoroughly familiar with the features of the product before
Failure to operate the product correctly can result in damage to the product or personal property and it can cause serious
injury.
operating.
This is a sophisticated hobby product.It must be operated with caution and common sense and requires some basic mechanical ability.Failure to
opera-te this product in a safe and responsible manner could result in injury or damage to the product or other property.This product is not
intended for use by children without direct adult supervision.Do not use with incompatible components or alter this product in any way contrary to
the instructions provided by
HSD HOBBY LTD. This manual contains instructions for safety,operation and maintenance.It is essential to read and
follow all the instructions and warn-ings in the manual prior to assembly,setup or use, in order to correctly operate the product and/or avoid
damage or serious injury.
14+
Not for children under 14
years.This is not a toy.
AGE RECOMMENDATON:
As the user of this product,you are solely responsible for operating it in a
man-ner that does not endanger yourself and/or others or result in damage
to the product and property of others.
•
Always keep a safe distance, in all directions, around your model to avoid
collisions or injury.This model is controlled by a radio signal subject to
interference from many sources outside of your control; interference can
cause momentary loss of control.
• Always operate your model in open spaces away from full-size vehicles,
traffic and people.
• Always carefully follow the directions and warnings for this and any optional
support equipment (chargers,rechargeable battery packs,etc.).
•
Always keep all chemical,small and electric parts out of the
reach of children.
• A lways avoid water exposure to all equipment that is not speciffically
designed for this purpose.Moisture causes damage to electronics.
• N ever place any portion of the model in your mouth as it could cause
serious injury or death.
• Never operate your model with low transmitter batteries.
• Always keep aircraft in sight and under control.
• Always use fully charged batteries.
•
Always keep the transmitter in the on state while aircraft is in use.
• Always remove batteries before disassembly.
• Always keep moving parts clean.
• Always keep parts dry.
•
Always let the parts cool before touching after use.
• Always remove batteries after use.
• Always ensure failsafe is properly set before flying .
• Never operate aircraft with damaged wiring.
• Never touch moving parts.
Safety Precautions and Warnings
NOTICE
All rights reserved by HSD for the upgrade and/or reconfiguration of products.
Thank you for purchasing from HSD. Please read this manual carefully before operating this plane. We hope this manual is useful
in guiding you through the installation and adjustment of the plane so that you may successfully fly it.
Each product from HSD has unique functions that users will need to fully grasp step by step, as you will complete the assembly. It is
necessary to assemble and test the product strictly in accordance with HSD's standards.
CONTENTS
Specifications
Assembl y
Throttle Range Setting
CG Location.....................
Accessories
Model Flying Precautions
Box Contents....................................................................................01
......................................................................01
....... . . . . . . . . . . ....... . . . . . . . . . . ....... . . . . . . . . . . ....... . . . . . . . . . . ....... . . 0 2
Control Horn and Servo Arm Settings..............................................03
Control Direction Test..................................................................04
Cl e v i s In s t a l la t io n .. . . . . . . . . . . . .. . . . . . . . . . . . ... . . . . . . ...............................05
Control Surface Centering.................................................................05
..................................................................05
........................................................06
..................................................................06
...............................................................................07-08
Trouble Sho ot in g...................................... .. .. ...........................09
.....................................................................10
P r e - F l i g h t Ch e c k s . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . 1 0
Installation Of Battery
01
Box Contents
1100mm
969mm
4S 1250g
6S 1450g
Specifications
Brushless Outrunner Motor, 3060/2600KV(4S)
3060/2000KV(6S)
HOBBYWING 60A Pro Brushless ESC(2-6S)
Servos:（twin bearings,metal shell and digital
servos)9g*6pcs
Battery:4S 2200mAh-3300mAh 40C Li-Po
6S 2200mAh-3300mAh 40C Li-Po
Radio System: 2.4GHz 4CH
Transmitter and Receiver
75mmEDF
Installed
Installed
Installed
Required to Complete
Required to Complete
Attention
EDF jets require Li-PO batteries with a high discharge rating (C rating) for increased safety and
optimal performance. We recommend using Li-Po batteries with a minimum of 40C or above.
02
Assembly
4
2
5
3
Assembly of your Viper is completed.
Now perform a final check on all screws,
bolts and components,ensuring all are secure
and firmly in place.
1
PA 3*15MM 1pcs
PA 3*18MM 1pcs
PA 2.6*6MM 1pcs
PA 3*5MM 2pcs
PA 2.6*6MM 2pcs M3*3MM 1pcs
PA 2.6*6MM 4pcs
Fixed with screws
Connect the servo link and fix the screws
Connect the servo link and fix the screws
03
Control Horn and Servo Arm Settings
After flying y ou may choose to adjust the linkage positions for the desired control response.See the lower table.
The table to the right shows the factory settings for the control horns and servo arms.Fly the aircraft at factory settings before
making changes.
Horns Arms
Elevator
Rudder
Ailerons
Increased Thrust Control Decreased Thrust Control
The Rudder
The front
wheel steering
The Rudder The front
wheel steering
04
Control Direction Tests
After binding a transmitter to the aircraft receiver,set the trims and
center the control surfaces.sub-trims to 0,then adjust the clevises to
Move the controls on the transmitter to make sure the aircraft control surfaces move in the proper direction.
Assemble the aircraft and bind your transmitter to the receiver before performing this test.
Transmitter
Command Aircraft Reaction
Elevator
Up Elevator
Command
Down
Elevator
Command
Aileron
Stick Right
Stick Left
Rudder
Stick Right
Stick Left
Small
Big
the Throttle
05
Control Surface Centering
centered.If the control surfaces are not centered, mechanically center the
control surfaces by adjusting the linkages.
1.
2.
3.
4.
5.
6.
Clevis Installation
After assembly and transmitter setup,verify that the control surfaces are
Throttle range setting
(Throttle range should be reset whenever a new transmitter is being used)
With the flaps switch in the up position,flaps should be adjusted so they are
even with the ailerons and/or the root of the wing.
If adjustments are required, turn the ball buckle on the pushrod to
change the length of the linkage between the servo arm and the
control horn. After binding a transmitter to the aircraft receiver, set
the trims and sub-trims to 0, then adjust the ball buckles as necessary
to center the control surfaces.
Step 1:Switch on the transmitter and move the throttle stick to 100%
(wide-open throttle).
Step 2:Connect the battery pack to the ESC, and wait about 2 seconds.
Step 3:A 'beep-beep' tone will emit, this means the highest point in the
throttle control range has been confirmed.
Step 4:After the 'beep-beep' tone is emitted, move the throttle stick
back down to the lowest position (0%). You will hear a set of
initialization beeps that register the number of cells in the battery.
Step 5:A final, long beep tone will be emitted meaning that the lowest
point of the throttle range has been confirmed. This means the throttle
control has been initialized properly and is ready for use.
* Adjust the push-rod and clevis as necessary.
*Carefully adjust the clevis so that it creates a centered surface
when attached to the control horn.
06
CG LOCATION
Installation of battery:
-10mm
+10mm
-10mm
+10mm
-10mm
+10mm
Recommended battery location for
4S 3300mAh (350g) Li-Po.
Recommended battery location for
6S 3300mAh (550g) Li-Po.
CG
85MM
07
Accessories
HSDA75-T01 HSDA75-T02 HSDA75-T03 HSDA75-T04
H S D A 7 5 - T 0 5 H S D A 7 5 - T 0 1 1 3 5 H S D - T B 0 2 H S D - B B 0 1
H S D - B A 0 2
HSD-TD01
H S D - T D 0 2 H S D A 7 5 - T 0 6 H S D - M 0 2 H S D A 7 5 - T A 0 1
HSD-BA01 H S D - B C 0 1 H S D - B C 0 2
HSD-BC03 HSD-BC04 HSD-TM01
Otros manuales para ViperJET
1
Tabla de contenidos
Otros manuales de Juguete de HSD
HSD
HSD 105mm Super Viper Manual de usuario
HSD
HSD T45 Goshawk Manual de usuario
HSD
HSD Super Viper Manual de usuario
HSD
HSD A1 Manual de usuario
HSD
HSD HSD-105MM-16 Manual de usuario
HSD
HSD Sky Trainer Manual de usuario
HSD
HSD ViperJET Manual de usuario
HSD
HSD 105mm Super Viper Manual de usuario
HSD
HSD J10 Manual de usuario
