HSD ViperJET Manual de usuario
ViperJET
75mm EDF
WARNING:
Read this instruction manual entirely to become thoroughly familiar with the features
of
the
product
before
operating.
Failure
to
operate
the product correctly can result in damage
to
the
product or personal property and it can cause serious injury.
This is a sophisticated hobby product.It must be operated with caution, common sense, and requires some basic mechanical ability.Failure to
operate this product in a safe and responsible manner could result in physical injury or damage to the product or other
property.This product is
not intended for use by
children without direct adult supervision.Do not use with incompatible components or alter this product in any way
contrary to the instructions provided by
HSD HOBBY LTD. This manual contains instructions for safety,operation and maintenance.It is
essential to read and follow all the instructions and warnings in the manual
prior to assembly,setup or use, in order to correctly operate the
product and/or avoid damage or serious injury.
14+
AGE RECOMMENDATON:
Not for children under 14 years
of age
.This is not a toy.
As the user of this product,
you are solely responsible for operating it in a manner that does not endanger yourself and/or others or result in
damage
to the product and property of others.
Always keep a safe distance, in all directions, around your model to avoid collisions or injury.This model is controlled by a radio signal subject to interference from
many sources outside of your control; interference can cause momentary loss
o
f control.
Always operate your model in open spaces away from full-size vehicles,
traffic and people
.
Always carefully follow directions and warnings for this model, and any optional support e
quipment (i.e., chargers, rechargeable battery packs, etc).
Always let parts cool down, after use, before touching or to use again.
Always keep all chemical, small and electric parts, out of children's reach.
Always avoid water exposure to all equipment that is not specifically designed for this purpose as moisture causes damage to electrics.
Never operate your model with low transmitter batteries.
Always keep aircraft in sight and under control.
Always keep the transmitter on for as long as the aircraft is in use.
Always remove batteries after use.
For your safety, do not touch moving parts.
Never operate aircraft with damaged wires.
Always ensure failsafe is properly set before flying.
Charging Warnings
CAUTION:
All instructions and warnings must be followed
exactly.
Mishandling of Li-Po batteries can result in a fire,personal injury,and/or
property damage.
•
By handling,charging
,
or using the included Li-Po battery,you assume
all
risks associated with lithium batteries.
•
If,
at any time,
the battery begins to balloon or swell, discontinue use
immediately. If charging or discharging, discontinue and disconnect.
Continuing to use, charge
,
or discharge a battery that is ballooning or
swelling can result in a fire.
• Always disconnect the battery after charging,and let the charger cool between charges.
• Always consistently monitor the temperature of the battery pack while charging.
• Never attempt to dismantle or alter the charger.
• Never allow minors under the age of 14 to charge battery packs.
• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
• Never leave charging batteries unattended.
• Never charge batteries over recommended levels.
• Never charge batteries in extremely hot or cold places.
• Do not store battery or aircraft in a car or direct sunlight. If stored in a hot car,the battery can catch fire or be damaged.
• Always store the battery at room temperature in a dry area for best results.
• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO BATTERIES. Failure to charge the battery with a compatible
charger may cause fire, resulting in personal injury and/or property damage.
.
Safety Precautions and Warnings
NOTICE
Thank you for purchasing
this HSD product
. Please read this manual carefully before operating this plane. We hope this manual is useful
in guiding you through the installation and adjustment of the plane so that you may successfully fly it.
Each product from HSD has unique functions that users will need to fully grasp step by step as you will complete the assembly. It is necessary to
assemble and test the product strictly in accordance with HSD's standards.
All rights reserved by HSD for the upgrade and/or reconfiguration of products.
Meaning of Special Language:
The following terms are used throughout the product manual to indicate various levels of potential harm when operating this product:
NOTICE: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
CAUTION: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
WARNING: If procedures are not properly followed, the risk of physical property damage AND a possibility of serious injury are likely.
CONTENTS
Specifications
Assembly
Box
Content
Control Horn and Servo Arm Settings
Control Direction Test
Clevis Installation
Control Surface Centering
Accessories
Troubleshooting
Flight Precaution
Pre-flight Check
Battery Installation
1
1
2
3
4
5
5
Throttle Range Setting
CG Configuration 6
6
7
9
10
10
-----------------------------------------------------------------------------------
----------------------------------------------------------------------------------
-------------------------------------------------------------------------------
---------------------------------------------------------------------------------------
------------------------------------------------------------------------------
-----------------------------------------------------------------------------
----------------------------------------------------------------------------
------------------------------------------------------------------------------------
------------------------------------------------------
-------------------------------------------------------------------------
-------------------------------------------------------------------
------------------------------------------------------------------------------
-------------------------------------------------------------------------------
----------------------------------------------------------------------- 5
01
Box Contents
1100mm
969mm
4S 1250g
6S 1450g
Specifications
Brushless Outrunner Motor 3060/2600KV (4S)
3060/2000KV (6S)
Hobbywing 60A Pro BrushlessESC (2-6S)
Six analog 9g servos
Battery:
4S 2200mAh-3300mAh 40C Li-Po
6S 2200mAh-3300mAh 40C Li-Po
Radio System: 2.4GHz 4CH
Transmitter and Receiver
75mm EDF
Installed
Installed
Installed
Required to Complete
Required to Complete
Attention
EDF jets require Li-PO batteries with a high discharge rating (C rating) for increased safety and
optimal performance. We recommend using Li-Po batteries with a minimum of 40C or above.
02
Assembly
4
2
5
3
Assembly is now complete.
and bolts are secure and firmly in
place before proceeding to the next pages.
1
PA 3*15MM 1pcs
PA 3*18MM 1pcs
PA 2.6*6MM 1pcs
PA 3*5MM 2pcs
PA 2.6*6MM 2pcs M3*3MM 1pcs
PA 2.6*6MM 4pcs
Fixed with screws
Connect the servo link and fix the screws
Connect the servo link and fix the screws
Make sure that all screws
6
03
Control Horn and Servo Arm Settings
After flying y ou may choose to adjust the linkage positions for the desired control response.
See the lower table.
The table below shows the factory settings for the control horns and servo arms. Fly the aircraft at
factory
settings
before
making any modifications.
.
Horns Arms
Elevator
Rudder
Ailerons
Increased Thrust Control Decreased Thrust Control
The Rudder
The front
wheel steering
The Rudder The front
wheel steering
04
Control Direction Test
After binding a transmitter
.
the controls on the transmitter to make sure the aircraft control surfaces move in the proper direction. .
Assemble the aircraft and bind your transmitter to the receiver before performing this test.
Transmitter
Command Aircraft Reaction
ElevatorAileron
Move right
stick right
stick left
Rudder
Move left
stick right
Move left
stick left
Low
Full
Move left
stick
up/down
to the aircraft receiver, set the trims and sub-trims to 0, then adjust the clevises to center the control surfaces. Move
Move right
Move right
stick down
Move right
stick up
Throttle
05
1.
2.
3.
4.
5.
6.
Throttle range setting
(Throttle range should be reset whenever a new transmitter is being used)
Step 1: Switch on the transmitter and move the throttle stick to 100% (wide-open throttle)
Step 2: Connect the battery pack to the ESC, and wait about 2 seconds
Step 3:
A
'beep-beep' tone will emit, this means the highest point in the throttle control range has
has been confirmed
Step 4: After the 'beep-beep' tone is emitted, move the throttle stick back down to the lowest
position (0%). You will then hear a set of initialization beeps that register the number of cells in
the battery
Step 5: A final long beep tone should sound, meaning that the lowest point of the throttle range
has been confirmed. This means the throttle control has been initialized properly and is ready
for use
Clevis Installation
*
Adjust the push rod and clevis as necessary
*Carefully adjust the clevis so that it creates a centered
surface when attached to the control horn.
Control Surface Centering
*After assembly and transmitter setup, verify that the
contro
.
l surfaces are centered. If the control surfaces
are not centered, manually cen
.
ter the control surfaces by
adjusting the linkages.
*With the flaps switch in the up position, flaps should be
adjusted so that they are even with the ailerons/root of
the wing.
*If adjustments are required, turn the ball buckle on the
push rode to change the length of the linkage between
the servo arm and the control horn. After binding the
transmitter to the receiver, set the trim and sub-trims to
0, then adjust the ball buckles as necessary to center
the control surfaces.
06
CG Location
Battery Installation
-10mm
+10mm
-10mm
+10mm
-10mm
+10mm
Recommended battery location for
4S 3300mAh (350g) Li-Po Recommended battery location for
6S 3300mAh (550g) Li-Po
CG
85MM
Make sure the center of gravity (CG) is as indicated in the following diagram:
07
Accessories
HSDA75-T01
HSDA75-T02
HSDA75-T03 HSDA75-T04
HSDA75-T05 HSDA75-T01135 HSD-TB02
HSD-BB01
HSD-BA02
HSD-TD01
HSD-TD02 HSDA75-T06 HSD-M02 HSDA75-TA01
HSD-BA01
HSD-BC01
HSD-BC02
HSD-BC03 HSD-BC04 HSD-TM01
Otros manuales para ViperJET
1
Tabla de contenidos
Otros manuales de Juguete de HSD
HSD
HSD Super Viper Manual de usuario
HSD
HSD 105mm Super Viper Manual de usuario
HSD
HSD Sky Trainer Manual de usuario
HSD
HSD J10 Manual de usuario
HSD
HSD T45 Goshawk Manual de usuario
HSD
HSD 105mm Super Viper Manual de usuario
HSD
HSD A1 Manual de usuario
HSD
HSD HSD-105MM-16 Manual de usuario
HSD
HSD ViperJET Manual de usuario
