HPE Aruba 6200F Manual del propietario

HPE Aruba Networking CX

6200F Switches and Accessories

Start Here: Installation, Safety, and Regulatory

Information

Published: January 2024

Edition: 3

Start Here: Installation, Safety, and Regulatory Information 2

Open Source Code

This product includes code licensed under certain open source licenses which require source

compliance. The corresponding source for these components is available upon request. This offer is

valid to anyone in receipt of this information and shall expire three years following the date of the final

distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source

code, please check if the code is available in the HPE Software Center at

https://myenterpriselicense.hpe.com/cwp-ui/software but, if not, send a written request for specific

software version and product for which you want the open source code. Along with the request, please

send a check or money order in the amount of US $10.00 to:

Hewlett Packard Enterprise Company

Attn: General Counsel

WW Corporate Headquarters

1701 E Mossy Oaks Rd, Spring, TX 77389

United States of America

All Product Documentation

For the latest release of hardware and software documentation for HPE Aruba Networking switches and

accessories, including the Installation and Getting Started Guide, which provides detailed installation

instructions, visit the Aruba Support Portal at the following link:

https://asp.arubanetworks.com/downloads

See the rest of this guide for important pre-setup information.

NOTE:

There are no user-serviceable parts in this product. For switch or accessory service needs, contact an authorized Aruba

representative.

Applicable products

Non-TAA TAA

HPE Aruba Networking CX 6200F 12G Class4 PoE

2G/2SFP+ 139W Switch (R8Q72A)

HPE Aruba Networking CX 6200F 12G Class4 PoE

2G/2SFP+ 139W TAA Switch (R8V13A)

HPE Aruba Networking CX 6200F 24G 4SFP+ Switch

(JL724B)

HPE Aruba Networking CX 6200F 24G 4SFP+ TAA-

compliant Switch (S0M86A)

HPE Aruba Networking CX 6200F 24G Class 4 PoE

4SFP+ 370W Switch (JL725B)

HPE Aruba Networking CX 6200F 24G Class 4 PoE

4SFP+ 370W TAA-compliant Switch (S0M87A)

HPE Aruba Networking CX 6200F 48G 4SFP+ Switch

(JL726B)

HPE Aruba Networking CX 6200F 48G 4SFP+ TAA-

compliant Switch (S0M88A)

HPE Aruba Networking CX 6200F 48G Class 4 PoE

4SFP+ 370W Switch (JL727B)

HPE Aruba Networking CX 6200F 48G Class 4 PoE

4SFP+ 370W TAA-compliant Switch (S0M89A)

HPE Aruba Networking CX 6200F 48G Class 4 PoE

4SFP+ 740W Switch (JL728B)

HPE Aruba Networking CX 6200F 48G Class 4 PoE

4SFP+ 740W TAA-compliant Switch (S0M90A)

Aruba 6200F 24G 4SFP+ Switch (JL724A) HPE Aruba Networking CX 6200F 24G 4SFP TAA-

compliant Switch (S0G13A)

Aruba 6200F 24G Class 4 PoE 4SFP+ 370W Switch

(JL725A)

HPE Aruba Networking CX 6200F 24G Class 4 PoE 4SFP

370W TAA-compliant Switch (S0G14A)

Aruba 6200F 48G 4SFP+ Switch (JL726A) HPE Aruba Networking CX 6200F 48G 4SFP TAA-

compliant Switch (S0G15A)

Aruba 6200F 48G Class 4 PoE 4SFP+ 370W Switch

(JL727A)

HPE Aruba Networking CX 6200F 48G Class 4 PoE 4SFP

370W TAA-compliant Switch (S0G16A)

Aruba 6200F 48G Class 4 PoE 4SFP+ 740W Switch

(JL728A)

HPE Aruba Networking CX 6200F 48G Class 4 PoE 4SFP

740W TAA-compliant Switch (S0G17A)

Start Here: Installation, Safety, and Regulatory Information 3

Start Here: Installation, Safety, and Regulatory Information 4

Non-TAA TAA

HPE Aruba Networking CX 6200F 24G 4SFP Switch

(S0M81A)

HPE Aruba Networking CX 6200F 24G Class 4 PoE 4SFP

370W Switch (S0M82A)

HPE Aruba Networking CX 6200F 48G 4SFP Switch

(S0M83A)

HPE Aruba Networking CX 6200F 48G Class 4 PoE 4SFP

370W Switch (S0M84A)

HPE Aruba Networking CX 6200F 48G Class 4 PoE 4SFP

740W Switch (S0M85A)

Overview

The HPE Aruba Networking CX 6200F Switch Series is a family of edge networking stackable switches,

ideal for enterprise network access. They provide the foundation for high-performance networks

supporting IoT, mobile, and cloud applications.

These switches are intended for indoor use only. They are for use in commercial applications. A typical

installation is in an environmentally controlled location. The end use environment may or may not be a

restricted access location.

A tool is required to remove the top cover; however, the product is not considered serviceable by an

operator.

Installation precautions and guidelines

To help avoid personal injury or product damage when installing your switch, read the following

installation precautions and guidelines.

WARNING:

nWith the exception of HPE Aruba Networking CX 6200F 12G Class4 PoE 2G/2SFP+ 139W switch

(R8Q72A) and HPE Aruba Networking CX 6200F 12G Class4 PoE 2G/2SFP+ 139W TAA Switch (R8V13A),

do not mount the switch on a wall, under a table, or under any other horizontal surface.

nMount devices installed in a rack or cabinet as low as possible. Put the heaviest devices at the bottom

and progressively lighter devices positioned higher.

nTo prevent the rack or cabinet from becoming unstable and/or falling over, ensure that it is

adequately secured.

This section provides precautions and guidelines to observe when installing your switch. For full

installation instructions, see the Installation and Getting Started Guide.

Start Here: Installation, Safety, and Regulatory Information 5

CAUTION:

nDo not ship any switch in a rack without checking for restrictions in the latest Installation and

Getting Started Guide. Otherwise, you may void the switch warranty.

nEnsure the power source circuits are properly grounded. Then connect the switch to the power

source by using the power cord supplied with the switch. For more information on power cords,

see the Power cords section.

nWhen installing the switch, the AC outlet should be near the switch and be easily accessible in

case the switch must be powered off.

nEnsure that the power cord and network cables at the switch mounting location do not create a

tripping hazard.

nDo not install the switch in an environment where the operating ambient temperature exceeds its

specification. See the environmental operating temperature information in the latest Installation

and Getting Started Guide.

nEnsure that the switch does not overload the power circuits, wiring, and over-current protection.

To determine the possibility of overloading the supply circuits, add the ampere ratings of all

devices installed on the same circuit as the switch. Then compare the total with the rating limit for

the circuit. The maximum ampere ratings for a device are usually printed near the device AC

power connectors.

nDo not block any ventilation openings on the front or rear of the switch.Ensure that the air flow

around the switch is not restricted.

oFor all other 24- and 48-port 6200F models: In the front or the back of the switch, leave at

least 7.6 cm (3 inches) of space for the twisted-pair and fiber-optic cabling. For the air flow

direction, see the latest Installation and Getting Started Guide.

oFor Aruba 6200F 12G Class4 PoE 2G/2SFP+ 139W Switch (R8Q72A) and Aruba 6200F 12G

Class4 PoE 2G/2SFP+ 139W TAA Switch (R8V13A) models: In the front or the back of the

switch, leave at least 15.24 cm (6 inches) of space for the twisted-pair and fiber-optic cabling.

nMarking label (includes power rating) is at the bottom of the switch.

nThe switch equipment is not suitable for use in locations where children are likely to be present.

NOTE:

nUse only supported Aruba transceivers and DACcabes.

nThe HPEAruba Networking CX 6200F switch port side transceiver slots support SFP and SFP+

transceivers.

nFor more information, see the latest version of the following two guides:

oInstallation and Getting Started Guide

oTransceiver Guide

Power cords

HPE Aruba Networking includes the power cord intended for use with your HPE Aruba Networking

switch. Different countries/regions may require different power cords. For a list of the power cords that

apply to your switch, see the section that lists power cords in the latest edition of the Installation and

Getting Started Guide for your switch.

Start Here: Installation, Safety, and Regulatory Information 6

CAUTION:

OnlyHPE Aruba Networking-approved power cords may be used with HPE Aruba Networking devices.

To access power cord information for your switch, see the latest edition of the HPE Aruba Networking

CX 6200F/M Installation and Getting Started Guide. Lost or damaged power cords must be replaced only

with HPE Aruba Networking-approved power cords. If your installation requires a different power cord

than the one supplied with the switch, be sure that the cord is adequately sized for the current

requirements of the switch. In addition, be sure to use a power cord displaying the mark of the safety

agency that defines the regulations for power cords in your country/region. The mark is your assurance

that the power cord can be used safely with the switch.

CAUTION:

Do not use a damaged or non-recommended power cord with your switch. Using such power cords voids

the switch warranty. It can also cause serious electrical problems, including injury or death to personnel,

and damage to the switch and other property. If you cannot verify that you have a power cord approved

for use with your switch model, contact your authorized HPE Aruba Networking dealer or sales

representative for assistance.

WARNING:

Remove the power cord from the switch before mounting or dismounting the switch.

Japan power cord warning

CAUTION:

FOR INDOOR USE ONLY. The switch, power cords, and all connected cables are not designed for outdoor

use.

Brazil Statement

Este equipamento deve ser conectado obrigatoriamente em tomada de rede de

energia elétrica que possua aterramento (três pinos), conforme a Norma NBR

ABNT 5410, visando a segurança dos usuários contra choques elétricos.)

CAUTION: Shock hazard. To completely remove power from the switch,

disconnect all power cords.

Environmental specifications

Start Here: Installation, Safety, and Regulatory Information 7

Table 1: Environmental Specifications for all HPE Aruba Networking CX 6200F switch models

Aruba CX 6200FSwitches

Operating temperature 32°F to 113°F (0°C to 45°C) up to 5,000 ft; Derate -1°C for every 1,000

ft from 5,000 ft to 10,000 ft

Non-operating temperature 5% to 95% @ 104°F (40°C) non-condensing

Operating relative humidity -40°F to 158°F (-40°C to 70°C) up to 15000 ft

Non-operating storage relative humidity 5% to 95% @ 149°F (65°C) non-condensing

Max operating altitude 10,000 ft (3.048 km) Max

Max non-operating altitude 15,000 ft (4.6 km) Max

Table 2: Dimensions and weights for HPE Aruba Networking CX 6200F switch models

Switch Weight Dimensions (W x D x H)

HPE Aruba Networking CX 6200F 24G

4SFP+ Switch (JL724B)

3.77 kg(8.32 lbs) 44.25 cm x 28.4 cm x 4.37 cm

(17.42 in x 11.2 in x 1.72 in)

HPE Aruba Networking CX 6200F 24G

4SFP Switch (S0M81A)

HPE Aruba Networking CX 6200F 24G

4SFP+ TAA-compliant Switch (S0M86A)

HPE Aruba Networking CX 6200F 24G

4SFP TAA-compliant Switch (S0G13A)

HPE Aruba Networking CX 6200F 48G

4SFP+ Switch (JL726B)

3.9 kg (8.59 lbs)

HPE Aruba Networking CX 6200F 48G

4SFP Switch (S0M83A)

HPE Aruba Networking CX 6200F 48G

4SFP+ TAA-compliant Switch (S0M88A)

HPE Aruba Networking CX 6200F 48G

4SFP TAA-compliant Switch (S0G15A)

Start Here: Installation, Safety, and Regulatory Information 8

Switch Weight Dimensions (W x D x H)

HPE Aruba Networking CX 6200F 24G

Class 4 PoE 4SFP+ 370W Switch (JL725B)

4.39 kg (9.68 lbs) 44.25 cm x 30.43 cm x 4.37 cm

(17.42 in x 11.98 in x 1.72 in)

HPE Aruba Networking CX 6200F 24G

Class 4 PoE 4SFP 370W Switch (S0M82A)

HPE Aruba Networking CX 6200F 24G

Class 4 PoE 4SFP+ 370W TAA-compliant

Switch (S0M87A)

HPE Aruba Networking CX 6200F 24G

Class 4 PoE 4SFP 370W TAA-compliant

Switch (S0G14A)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP+ 370W Switch (JL727B)

4.87 kg (10.74 lbs)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP 370W Switch (S0M84A)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP+ 370W TAA-compliant

Switch (S0M89A)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP 370W TAA-compliant

Switch (S0G16A)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP+ 740W Switch (JL728B)

5.13 kg (11.32 lbs) 44.25 cm x 32.66 cm x 4.37 cm

(17.42 in x 12.86 in x 1.72 in)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP 740W Switch (S0M85A)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP+ 740W TAA-compliant

Switch (S0M90A)

HPE Aruba Networking CX 6200F 48G

Class 4 PoE 4SFP 740W TAA-compliant

Switch (S0G17A)

HPE Aruba Networking CX 6200F 12G

Class4 PoE 2G/2SFP+ 139W Switch

(R8Q72A)

3.24 kg (7.14 lbs) 25.4 cm x 30.5 cm x 4.39 cm

(10.0 in x 12.0 in x 1.73 in)

HPE Aruba Networking CX 6200F 12G

Class4 PoE 2G/2SFP+ 139W TAA Switch

(R8V13A)

Start Here: Installation, Safety, and Regulatory Information 9

Switch Weight Dimensions (W x D x H)

Aruba 6200F 24G 4SFP+ Switch (JL724A) 4.36 kg (9.61 lbs) 44.25 cm x 32.7 cm x 4.37 cm

(17.42 in x 12.9 in x 1.72 in)

Aruba 6200F 24G Class4 PoE 4SFP+

370W Switch (JL725A)

4.9 kg (10.8 lbs)

Aruba 6200F 48G 4SFP+ Switch (JL726A) 4.45 kg (9.81 lbs)

Aruba 6200F 48G Class4 PoE 4SFP+

370W Switch (JL727A)

5.05 kg (11.13 lbs)

Aruba 6200F 48G Class4 PoE 4SFP+

740W Switch (JL728A)

5.10 kg (11.24 lbs)

xxx

Safety and regulatory information

NOTE:

For important safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage,

Power, Networking, and Rack Products, available at http://www.hpe.com/support/Safety-Compliance-EnterpriseProducts.

JL724A, JL725A, JL726A,

JL727A, JL728A

R8Q72A,

R8V13A

JL724B, JL725B, JL726B,

JL727B, JL728B, S0M81A,

S0M82A, S0M83A,

S0M84A, S0M85A,

S0M86A, S0M87A,

S0M88A, S0M89A,

S0M90A, S0G13A,

S0G14A, S0G15A,

S0G16A, S0G17A

Safety-EU

EN 62368-1:2014 +A11:2017 2nd Ed.

EN 62368-1:2020 +A11:2020 3rd Ed.

Safety-Worldwide

IEC 60950-1:2005 + A1:2009 + A2:2013 with all known

National Deviations IEC 62368-1:2014 2nd ed. with all

known National Deviations IEC 62368-1:2018 3rd Ed. with

all known National Deviations

IEC 62368-1:2014 2nd ed.

with all known National

Deviations

IEC 62368-1:2018 3rd Ed. with

all known National Deviations

Safety-North America

US:UL 60950 2nd Ed.

CAN:CSA-C22.2 No. 60950-1-07

US:UL 62368 3rd Ed.

CAN:CSA-C22.2 No. 62368-1:14 3rd Ed.

EMC

BS/EN 55032:2015 +A11:2020/CISPR 32, Class A

BS/EN 55035:2017 +A11:2020/CISPR 35

FCC CFR47 Part 15:2014, Class A

Table 3: Safety and Regulatory information for HPE Aruba Networking CX 6200F switches

Start Here: Installation, Safety, and Regulatory Information 10

JL724A, JL725A, JL726A,

JL727A, JL728A

R8Q72A,

R8V13A

JL724B, JL725B, JL726B,

JL727B, JL728B, S0M81A,

S0M82A, S0M83A,

S0M84A, S0M85A,

S0M86A, S0M87A,

S0M88A, S0M89A,

S0M90A, S0G13A,

S0G14A, S0G15A,

S0G16A, S0G17A

ICES-0013, Class A

AS/NZS CISPR 32, Class A

VCCI-32, Class A

CNS 15936:2016

KS C 9832:2019

KS C 9835:2019

BS/EN 61000-3-2:2014

BS/EN 61000-3-3:2013

BS/EN 61000-3-2:2019

BS/EN 61000-3-3:2013/A1:2019

RoHS EN IEC 63000:2018

Regulatory Model

Number Model Number Descriptions

RSVLC-1910 JL728A Aruba 6200F 48G Class4 PoE 4SFP+ 740W Switch

RSVLC-1911 JL727A Aruba 6200F 48G Class4 PoE 4SFP+ 370W Switch

JL725A Aruba 6200F 24G Class4 PoE 4SFP+ 370W Switch

RSVLC-1912 JL726A Aruba 6200F 48G 4SFP+ Switch

JL724A Aruba 6200F 24G 4SFP+ Switch

RSVLC-2108 R8Q72A HPE Aruba Networking CX 6200F 12G Class4 PoE 2G/2SFP+

139W Switch

R8V13A HPE Aruba Networking CX 6200F 12G Class4 PoE 2G/2SFP+

139W TAA Switch

RSVLC-2205 JL726B HPE Aruba Networking CX 6200F 48G 4SFP+ Switch

JL724B HPE Aruba Networking CX 6200F 24G 4SFP+ Switch

S0M83A HPE Aruba Networking CX 6200F 48G 4SFP Switch

Table 4: Regulatory Model Numbers for Aruba 6200F switches

Otros manuales para Aruba 6200F

Tabla de contenidos

Otros manuales de Cambiar de HPE

HPE

HPE FlexNetwork 7500 Switch Manual de usuario

HPE

HPE FlexFabric 5710 Series Manual de usuario

HPE

HPE FlexNetwork NJ5000 5G PoE Plus Walljack Manual de usuario

HPE

HPE FlexNetwork 5130 EI Series Manual de instalación

HPE

HPE FlexFabric 5940 SERIES Manual de usuario

HPE

HPE 5820X Series Manual de usuario

HPE

HPE Aruba Instant On 1960 Instrucciones de montaje

HPE

HPE FlexFabric 5950 Series Manual de usuario

HPE

HPE Aruba Instant On 1960 24G 20p Class4 4p Class6 PoE 2XGT 2SFP+ 370W... Instrucciones de montaje

HPE

HPE Aruba 6200F Instrucciones de montaje

HPE

HPE Altoline 9960 LC1 Instrucciones de montaje

HPE

HPE FlexNetwork 5510 HI Series Manual de usuario

HPE

HPE FlexNetwork 7500 Series Manual de usuario

HPE

HPE Altoline 6940 32QSFP+ Instrucciones de montaje

HPE

HPE FlexFabric 5930 Series Manual de instalación

HPE

HPE Aruba 2930F Manual de usuario

HPE

HPE 3100 v2 Series Manual de usuario

HPE

HPE FlexNetwork 5510 HI Series Manual de usuario

HPE

HPE FlexNetwork 5510 HI Series Manual de usuario

HPE

HPE 12500 Series Manual de instalación

HPE

HPE OfficeConnect 1910 Series Guía de seguridad

HPE

HPE Aruba Instant On 1830 48G 4SFP Instrucciones de montaje

HPE

HPE Aruba 3810M Instrucciones de montaje

HPE

HPE SN6000B Manual de operación y mantenimiento

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario