HP 1810-8 Manual de usuario

HP 1810-8 and 8G Switch Quick Start Guide

For more detailed instructions and information to set up your switch, view or download the Installation and Getting Started

Guide for your switch at www.hp.com/networking/support.

1. Unpack and check included parts. ■Documentation kit

■Switch

■Accessory kit (installation hardware)

■Inline AC/DC adapter with power cord

or wall mount AC/DC adapter

2. Prepare for installation. To avoid personal injury or product damage, follow the “Safety Precautions” on

page 4.

3. Power on and verify that Self-Test completes normally. The switch does not have a power switch. It is powered on

by connecting the AC power adapter supplied with your switch, or by a PoE connection to Port 1 (8G Switch only).

After Self-Test:

Power LED = On

Fault LED = Off

4. Mount the switch. Unplug the AC power from the switch before mounting it.

Table or Desktop Mounting: Attach the four self-

adhesive pads (included in the accessory kit) to the bottom

corners of the switch.

4. Mount the switch. (continued)

Wall Mounting: Install two 5/8-inch (15.875 mm) Number

12 wood screws, (included) into the mounting surface,

positioned 5.5 inches (140 mm) apart. Use the wall anchors

if necessary. Then, position the switch over the screws and

slide to lock in place.

Important: For wall-mounting, the network ports must be

facing up or down. Do not mount the switch with

ventilation holes facing up or down. (See “Installation

Precautions” on page 4.)

Under-Table Mounting: Install the two screws on the

table bottom similarly to the procedures for wall mounting.

Then, position the switch over the screws and slide to lock

in place. Install the third screw at the side of the switch to

prevent it from sliding out of the locked position, if

necessary.

5. Power on the switch: Follow the same procedures as

in step 3.

It is recommended that you then secure the power cable

with the supplied cable tie.

6. Configure the switch for operation on your

network (minimal configuration).

Using a standard Ethernet cable, connect a PC directly to

any network port on the switch. Then configure the PC’s

IP Address and Subnet Mask to allow it to communicate

with the switch through your PC’s web browser.

Switch factory-default settings:

Parameter Factory Default Setting

Password <blank>

IP address 192.168.2.10

Subnet mask 255.255.255.0

Default gateway not set

Connect to

any port

Modify the switch’s IP configuration to operate in your network. See the example initial configuration page 3.

Note: When you are done with the initial switch configuration, disconnect the LAN cable from your PC and connect the

switch into the network.

Be sure to return your PC to its original network settings before connecting it to your network.

Example: Initial Switch Network Configuration using Windows®XP

1. Reconfigure the PC’s IP address and Subnet Mask so that it can communicate with the switch.

a. Click Start > Connect to > Show all connections.

b. Select and right-click Local Area Connection, then click Properties.

c. Scroll and select Internet Protocol (TCP/IP), then click Properties.

Note: Be sure to record all your PC’s current IP settings to be able to restore them later.

d. On the General tab, click Use the following IP address.

e. For IP address, enter an IP address in the same range as the switch’s default IP address. For example, enter 192.168.2.12.

f. For Subnet mask, enter 255.255.255.0, then click OK.

g. Click Close (or OK) to close the Local Area Connection Properties screen.

2. Open your web browser on the PC, and enter the switch factory-default address, http://192.168.2.10, to access the switch’s

web interface.

3. Click Log on to log onto the switch (by default, there is no password).

4. Click Network Setup > Get Connected and configure IP network settings on the switch for operation on your network.

Important: If you enable DHCP on the switch for automatic IP network configuration, at the time of that selection, the

switch must be connected to the same network as the DHCP server. Otherwise, the switch will revert to the 192.168.2.10

address. After automatic IP configuration, you must determine the IP address assigned to the switch. To do this, you will

need to access your DHCP server files, or use LLDP (Link Layer Discovery Protocol) commands on a connected device

(such as another switch).

5. Click Apply on the browser configuration screen to save your settings to retain them when the switch is rebooted.

You are done with initial switch configuration. Disconnect the LAN cable from your PC and connect the switch into the

network.

Be sure to return your PC to its original network settings before connecting it to your network.

7. Connect the network cables.

8. (Optional) Lock the Switch: Use a Kensington lock

or similar device (not included) to physically secure the

switch.

Safety Precautions

To avoid personal injury or product damage when installing your switch, read the installation precautions and guidelines below.

Installation Precautions

Warnings

■Do not wall-mount any switch without checking for restrictions in the Installation and Getting Started

Guide.

Wall-mount the switch with network ports facing up or down (away from or toward the floor). Do not wall-

mount the switch with the ventilation holes facing up or down.

Cautions

■Ensure the power source circuits are properly grounded, then use the power cord supplied with the switch to connect

to the AC power source.

■If your installation requires a different power cord than the one supplied with the switch and/or power supply, be

sure the cord is adequately sized for the switch’s current requirements. In addition, be sure to use a power cord

displaying the mark of the safety agency that defines the regulations for power cords in your country/region. The

mark is your assurance that the power cord can be used safely with the switch and power supply.

■When installing the switch, the AC outlet should be near the switch and should be easily accessible in case the switch

must be powered off.

■Ensure the switch does not overload the power circuits, wiring, and over-current protection. To determine the

possibility of overloading the supply circuits, add together the ampere ratings of all devices installed on the same

circuit as the switch and compare the total with the rating limit for the circuit. The maximum ampere ratings are

usually printed on the devices near the AC power connectors.

■Do not install the switch in an environment where the operating ambient temperature exceeds its specification.

■Ensure the air flow around the switch is not restricted. Leave at least 3 inches (7.6 cm) for cooling.

For additional Safety and Regulatory information, refer to the Safety and Regulatory documentation included with your switch.

Russia/Belarus/Kazakhstan/CEE Safety:

Printed in China

June 2012

5998-3195

The information contained herein is subject to change

without notice.

Otros manuales para 1810-8

Tabla de contenidos

Otros manuales de Cambiar de HP

HP 6125G/XG Instrucciones de uso

HP 445860-B21 - 10Gb Ethernet BL-c Switch Manual de usuario

HP ProCurve 5400zl Series Guía

HP 5920 Manual de instalación

HP NJ2000 Manual de usuario

HP 1810-24G Manual de usuario

HP J3128A AdvanceStack 10Base-T Hub-8E Manual de instalación y funcionamiento

HP 6125XLG Manual de instalación

HP Procurve 2524 Manual de instrucciones

HP ProCurve 3500-48 Instrucciones de montaje

HP AdvanceStack 100Base-T Hub-8TXE Manual de instalación y funcionamiento

HP StorageWorks 1606 - Extension SAN Switch Manual de operación y mantenimiento

HP A5830 Series Manual de instalación

HP StoreFabric SN6500B Instrucciones de uso

HP 6127XLG Blade Series Manual de instalación

HP V1910 Manual de usuario

HP 316095-B21 - StorageWorks Edge Switch 2/24 Manual de usuario

HP StorageWorks 64 - SAN Director Switch Manual técnico

HP StoreFabric SN4000B Manual de programación

HP 2/8q Fibre Channel Manual de usuario

HP ProCurve 8206zl Manual de usuario

HP StorageWorks edge switch 2/32 Manual de usuario

HP Officejet Pro 7500 Series Manual de usuario

HP HPE FlexFabric 5944 Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario