HP D2D Manual de usuario

HP D2D NAS

Integration with Symantec™ Backup Exec™

2010

Abstract

This guide provides step by step instructions on how to configure and optimize Symantec Backup Exec 2010 in order to back

up to HP D2D Backup Systems using a CIFS backup target.

HP Part Number: EH985-90932

Published: February 2011

Edition: 1

Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial

Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under

vendor's standard commercial license.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

WARRANTY STATEMENT: To obtain a copy of the warranty for this product, see the warranty information website:

http://www.hp.com/go/storagewarranty

Linear Tape-Open, LTO, LTO Logo, Ultrium and Ultrium Logo are trademarks of Quantum Corp, HP and IBM in the US, other countries or both.

Microsoft, Windows, Windows NT, and Windows XP are U.S. registered trademarks of Microsoft Corporation.

Symantec and Backup Exec™ are trademarks or registered trademarks of Symantec Corporation or its affiliates in the U.S. and other countries.

Contents

1 Configure the D2D CIFS server.....................................................................4

More about authentication modes...............................................................................................4

Configuring User Authentication mode........................................................................................5

Configuring AD Authentication Mode..........................................................................................6

To join a domain.................................................................................................................6

To create shares and grant access permission..........................................................................8

2 Configure Backup Exec to use D2D CIFS Share............................................12

Create a D2D CIFS target for backup........................................................................................12

Create a Backup Exec Backup-to-disk folder...............................................................................13

3 Configure a backup rotation scheme...........................................................18

To create a media set..............................................................................................................18

To create backup policy...........................................................................................................20

Housekeeping considerations..............................................................................................24

About this guide..........................................................................................25

Intended audience..................................................................................................................25

Related documentation............................................................................................................25

Document conventions and symbols..........................................................................................25

HP technical support...............................................................................................................26

HP websites...........................................................................................................................26

Documentation feedback.........................................................................................................26

Index.........................................................................................................28

Contents 3

1 Configure the D2D CIFS server

The first step in configuring the D2D device as a target for backups from Symantec Backup Exec

is to configure the CIFS server on the D2D Backup System

On the D2D Web Management Interface navigate to the NAS — CIFS Server page and select Edit.

The available Authentication options for the CIFS server are:

•None – All shares created are accessible to any user from any client (this is the least secure

option)

•User – Local (D2D) User account authentication

•AD – Active Directory User account authentication

More about authentication modes

None: This authentication mode requires no username or password authentication and is the

simplest configuration. Backup Exec will always be able to use shares configured in this mode with

no changes to either server or Backup Exec configuration. However, this mode provides no data

security because anyone can access the shares and add or delete data.

User: In this mode it is possible to create “local D2D users” from the D2D Web Management

Interface. This mode requires the configuration of a respective local user on the Backup Exec media

server and configuration changes to the Backup Exec services. Individual users can then be assigned

access to individual shares on the D2D Backup System. This authentication mode is ONLY

recommended when the Backup Exec media server is not a member of an AD Domain.

AD: In this mode the D2D CIFS server becomes a member of an Active Directory Domain. In order

to join an AD domain the user needs to provide credentials of a user who has permission to add

computers and users to the AD domain. After joining an AD Domain access to each share is

controlled by Domain Management tools and domain users or groups can be given access to

individual shares on the D2D Backup System. This is the recommended authentication mode, if the

Backup Exec Media server is a member of an AD domain.

4 Configure the D2D CIFS server

Configuring User Authentication mode

1. Select the User authentication mode on the D2D Web Management Interface and click Update

to create a local user account on the D2D Backup System. Provide a User Name and Password

for the new user.

2. Use Server Manager to create a correspondingly named user on the Windows server that

hosts the Backup Exec Media server.

3. It is then necessary to configure Backup Exec to use this Local user account as the credentials

used to run its services. Do this from the Backup Exec interface by selecting Tools — Backup

Exec Services ….

Then click the Services Credentials button and provide the new User Name, Domain name

(local server name) and password.

Configuring User Authentication mode 5

4. Restart the Backup Exec services before continuing with configuration. Note, however, that

this is the ONLY user account that the Backup Exec Media server will be able to use to connect

to remote storage that requires authentication, so this account must be the same for any other

disk storage devices.

Configuring AD Authentication Mode

These are the steps required in order to configure backups in AD authentication mode:

•Join the D2D CIFS server to the AD Domain and configure DNS.

•Create or specify a user to be used for backups.

•Apply user permissions to D2D shares.

•Configure Backup Exec services to use the correct Domain account.

To join a domain

1. Connect to the D2D Web Management Interface, navigate to the NAS — CIFS Server page,

click Edit and choose AD from the drop-down menu. Provide the name of the domain that you

wish to join, e.g “mydomain.local”

2. Click Update. If the domain controller is found, a pop-up box will request credentials of a user

with permission to join the domain. (Note that joining or leaving the domain will result in

failure of any backup or restore operations that are currently running.) Provide credentials

(username and password) of a domain user that has permission to add computers to the

domain and click Register.

6 Configure the D2D CIFS server

3. After joining the domain, the DNS server should be automatically updated (if a DHCP server

is used) with Forward and Reverse Lookup zone entries, however, some DNS configurations

do not allow this. In this case, or if a DHCP is not used on the network, the user must also

configure the domain’s DNS server to be able to correctly manage the D2D shares, as

described in the next section.

To configure entries manually if the DNS server does not update automatically

From a Windows client server that has domain and DNS management tools installed launch

the DNS Management Tool. (From the command line type dnsmgmt.msc or launch DNS

from the Administrative Tools menu).

Create a new Host(A) record in the forward lookup zone for the domain to which the D2D

Backup System belongs with the hostname and IP address of the D2D Backup System.

Also create a Pointer(PTR) in the reverse lookup zone for the domain for the D2D Backup

System by providing the hostname and IP address.

Configuring AD Authentication Mode 7

To create shares and grant access permission

Now that the D2D Backup System is part of a domain and can be managed, it is possible to create

shares and grant access permission to them for domain account users or groups.

1. Create a share on the D2D Backup System that is going to be used as a backup target, by

selecting NAS — Shares from the D2D Web Management Interface and clicking Create.

Provide a share Name and Description, select the CIFS protocol and click Create.

2. Now that the D2D Backup System is a member of the domain its shares can be managed

from any computer on the domain by configuring a customized Microsoft Management Console

(MMC) with the Shared Folders snap-in. To do this first open a new MMC window by typing

mmc at the command prompt or from the Start Search box. This will launch a new empty MMC

window.

8 Configure the D2D CIFS server

3. To this empty MMC window add the Shared Folders snap-in. Select File — Add/Remove

Snap-in ..., then select Shared Folders from the left-hand pane.

4. Click Add > and in the dialog box choose the computer to be managed and select Shares

from the View options.

5. Click Finish and OK to complete the snap-in set up.

Configuring AD Authentication Mode 9

Note that the Folder Path field contains an internal path on the D2D Backup System.

6. Save this customized snap-in for future use.

7. Select the Share Permissions tab and Add a user or group of users from the domain.

Specify the level of permission that the users will receive and click Apply.

8. Now, from any Windows server on the domain, it is possible to access the newly created

share using the credentials of anyone who had been given permission to access the share. If

a permitted user is logged into Windows, access to the share will be granted automatically

with those permissions.

10 Configure the D2D CIFS server

Otros manuales para D2D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de HP

HP GM415AA - Pocket Media Drive 160 GB External... Manual de usuario

HP Pavilion p6000 - Desktop PC Guía

HP STORAGEWORKS XP24000 Manual de usuario

HP Surestore 64 - Director Switch Manual de usuario

HP Invent EH861 Series Instrucciones de montaje

HP StoreEver ESL G3 Manual de usuario

HP Xw4550 - Workstation - 2 GB RAM Manual de usuario

HP StorageWorks NAS b2000 - v2 Manual de usuario

HP StorageWorks EVA4000 Guía

HP StorageWorks MSL5000 series Manual de usuario

HP C4405A - Colorado 14GB Tape Drive Manual de usuario

HP MSA 2040 Manual de usuario

HP M8502 Manual de usuario

HP 7957A Manual de usuario

HP 3PAR StoreServ 7200 2-node Instrucciones de montaje

HP StorageWorks XP12000 Manual de usuario

HP StorageWorks 1/8 G2 Manual de usuario

HP Surestore HVD10 - Disk System Manual de usuario

HP StorageWorks XP48 - Disk Array Manual de usuario

HP P2000 G3 Manual de usuario

HP LTO-4 Ultrium 1760 Manual del producto

HP D6030A - NetServer - E50 Manual de usuario

HP P9000 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario