HP P4522A - Traffic Management Server Sa8220 Manual de usuario

hp traffic director

server appliances

getting started guide for the hp

e-commerce traffic director server

appliances sa8200/sa8220 and the

hp traffic director server appliances

sa7200/sa7220

Hewlett-Packard Company

3000 Hanover Street

Palo Alto, CA 94304-1185

Publication Number

5971-0898

March 2001

Disclaimer

The information contained in this document is subject to change without notice.

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY

KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not

be liable for errors contained herein or for incidental or consequential damages

in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

Warranty

A copy of the specific warranty terms applicable to your Hewlett-Packard

products and replacement parts can be obtained from http://www.hp.com/

serverappliances/support/.

*Other brands and names are the property of their respective owners.

Getting Started

Before You Begin

This document will guide you through the installation and basic

configuration of your HP e-Commerce Traffic Director Server

Appliance SA8200/SA8220 and HP Traffic Director Server

Appliance SA7200/SA7220.

NOTE: For ease of

reading, all models are

referred to as the SA8220

throughout this

document. Unless noted

otherwise, all SA8220

references refer to all

models

This document covers the following topics:

• Physical installation

• Configuration checklists

• Running Setup using the Boot Monitor

• Configuring DNS

• Using the Graphical User Interface (GUI)

• Helpful hints

• Where to go from here

• Support information

HP Traffic Director Server Appliances Getting Started Guide

Parts Checklist Ensure that the items listed below are included in the box with your

system:

•HP e-Commerce Traffic Director Server Appliance SA8200/

SA8220 or HP Traffic Director Server Appliance SA7200/

SA7220, as appropriate

•HP Traffic Director Server Appliances User Guide

• HP Traffic Director Server Appliances Getting Started Guide

(this document)

• HP Traffic Director Server Appliances Release Notes

•AC power cord

•Null-modem cable

•RJ-45 network cable

•Rack and rail mounting brackets with Phillips mounting screws

Contact HP Customer Support if any of the above items are missing

from your shipment.

Support

Website Visit http://www.hp.com/serverappliances/support/

for late breaking information and for details regarding the current

software release.

Physical Installation

If you have already mounted your system, or if your system does not

require mounting, proceed to “Wiring Connections”later in this

document.

You can physically install the SA8220 in either of two ways. Each

installation method requires a particular type of mounting brackets,

and are included in the SA8220's shipping container.

•In a standard 19”rack, cantilevered from the mounting brackets

•In a cabinet with side rail mounts

Rack

Installation Rack mounting requires the use of the large mounting brackets, and

all eight of the included Phillips screws.

CAUTION: Do not use

the enclosed small

mounting brackets for

rack installation. These

are used for side rail

installation.

1. Locate the two large mounting brackets and the provided screws.

2. Attach alarge mounting bracket to each side of the SA8220. Use

four screws to secure each bracket to the holes near the front of

the SA8220, as shown below.

Rack Mounting the SA8220

NOTE: Thesescrewsare

provided with your rack

hardware, not the

SA8220.

3. Position the SA8220 in the desired space of your 19”rack and

attach the front flange of each mounting bracket to the rack with

two screws each.

HP Traffic Director Server Appliances Getting Started Guide

Side Rail

Installation Side rail mounting of the SA8220 requires the use of the enclosed

small mounting brackets and four of the Phillips head screws.

1. Locate the two small mounting brackets and the provided screws.

2. Attach a side rail to each SA8220 using the rows of five screw

holes on the side of the SA8220, equidistant from the top and

bottom, as shown below. The screws for this procedure are not

provided with the SA8220; they are supplied with your side rail

hardware.

Side Rail Mounting of the SA8220

NOTE: The small

mounting brackets have

recesses that allow them

to fit over the front end of

the side rail.

3. Attach a small mounting bracket to each side of the SA8220,

using two of the provided screws for each bracket. Use the holes

nearest to the front of the SA8220.

4. Slide the SA8220 into the cabinet’s receiving rails and secure the

front flange of each mounting bracket with two screws.

SA8220 bracket

holes

side-view

Mounting bracket side-view

(connect to SA8220) Rail mount holes

end-view

Physical Installation

Wiring

Connections 1. On the rear of the SA8220, connect the provided AC power

cable.

2. Refer to this diagram for all wiring connections on the front

panel of the SA8220.

Front Panel Ports and LEDs

3. For Single NIC (Network Interface Card) configurations:

Connect the Network port to your network using the provided RJ-

45 network cable.

For Dual NIC configurations: Connect the Network port to your

outside network, and the Server port to your server side network,

using the provided RJ-45 network cable and a network cable you

provide, respectively.

4. Use the provided serial cable to connect the Console serial port to

the serial port of any terminal or workstation capable of running

a terminal emulator program.

NOTE: For more

information about serial

cable failover, see

Chapter 2 in the User

Guide.

5. If you use cable-based failover to manage a backup SA8220,

connect the second SA8220 in the manner described above and

connect the Failover ports of the two units using the serial cable

provided with the backup SA8220.

6. If the power is not already on, turn on the SA8220 using the

Reset switch on the rear panel.

Power

Status

Act 1

Act 2

Console

Failover

Network Server Power

Status

Act 1

Act 2

Power

Status

Act 1

Act 2

Console

Failover

Network Server

HP Traffic Director Server Appliances Getting Started Guide

Configuring Your Terminal

This procedure assumes that you are running HyperTerminal* on

your workstation, and that your workstation is already connected to

the SA8220. If using another terminal emulator, you must adapt

these instructions as appropriate.

1. Note the serial port of your workstation (COM1, COM2, etc.)

2. Run HyperTerminal on your workstation.

3. In the Name field of the Connection Description window, type a

descriptive name, then click OK.

The Connect To panel displays.

4. In the Connect Using…list box, click “Direct to COM1”(or the

serial port you noted in step 1).

5. Click OK.

The COMn Properties panel displays, where nis your comm port

number.

6. Configure the port settings for 9600 baud, 8 data bits, no parity,

1 stop bit (9600-8-N-1), with flow control set to “None.”

7. Click OK.

8. From the File menu, click Properties.

9. Click the Settings tab.

10.Click the ASCII Setup button.

11.Change the values for Line and Character delay from 0 to at least

1 millisecond.

12.Click OK twice to exit.

13.Press Enter.

Configuring Your Terminal

Configuration

Checklists This section contains two configuration tables, the Quick Site

Configuration and the Detailed Site Configuration. One of these

must be filled out before continuing. We recommend using the

Detailed Site Configuration table on the next page. Its use is

mandatory when installing more than one SA8220. However, if you

are in a hurry and need to get a single SA8220 up and running

quickly, use the Quick Site Configuration below.

We recommend that you photocopy the Quick or Detailed Site

Configuration table, as appropriate. Fill out the copy before

proceeding, and keep it handy while you perform the installation

procedures.

For further information regarding the choices in these configuration

tables, see Chapter 2 in the User Guide.

Setting Choice

Hostname assigned to the SA8220’s network side

interface

IP address(es) assigned to the SA8220’s NIC

card(s), and associated subnet mask(s)

Default gateway for traffic from the SA8220 to the

network

The intended failover method oNONE oROUTE oSERIAL

Network side online IP address to be shared by

the two SA8220s, if you use serial cable failover

Quick Site Configuration

HP Traffic Director Server Appliances Getting Started Guide

Setting Parameter Choice

Hostname assigned to the SA8220’s

network side interface

Media Type o100BASE oAUTO

o10BASE

Duplex Type oFULL oAUTO

oHALF

Will the SA8220 use Dynamic Host

Configuration Protocol (DHCP)?

oYES

oNO

If not using DHCP, continue below:

Network port IP address

IP netmask

Server port IP address

IP netmask

Default gateway for traffic from the

SA8220 to the network

The intended failover method oNONE/DISABLED

oSERIAL oROUTE

For Serial Failover mode only:

Is the device primary or backup? Online IP

Online hostname

oPRIMARY

oBACKUP

Will Autoboot be enabled? Disabled by default oYES oNO

Will the SA8220 use Domain Naming

System (DNS)? oYES oNO

If using DNS, complete the following:

Domain Name

Primary DNS Server IP

Additional DNS Server IP

Detailed Site Configuration

Otros manuales para P4522A - Traffic Management Server Sa8220

Tabla de contenidos

Otros manuales de Servidor de HP

HP NetServer AA 4000 Manual de instrucciones

HP ProLiant DL380 Generation 4 Manual de usuario

HP 195294-001 - ProLiant - ML370R Instrucciones de funcionamiento y seguridad

HP ProLiant ML310 Generation 5p Instrucciones de uso

HP ProLiant SL390s G7 2U Manual

HP Sa3110 - VPN Server Appliance Manual de usuario

HP ML330 - ProLiant - G3 Manual de usuario

HP D7171A - NetServer - LPr Manual de usuario

HP Compaq t5515 Manual de usuario

HP D5970A - NetServer - LCII Manual de usuario

HP D7171A - NetServer - LPr Manual de usuario

HP BL460c - ProLiant - G5 Instrucciones de uso

HP Blade bc1000 Manual

HP rp8400 Series Manual de usuario

HP Integrity rx8640 Instrucciones de uso

HP D5970A - NetServer - LCII Manual de usuario

HP ML150 - ProLiant - G6 Manual de usuario

HP Integrity rx4640 Manual de usuario

HP Tc2120 - Server - 256 MB RAM Instrucciones de montaje

HP ProLiant ML110 - G2 Server Instrucciones de montaje

HP t5745 - Thin Client Instrucciones de uso

HP ProLiant DL320 Generation 4 Manual

HP DL385 - ProLiant - G5 Manual de usuario

HP Integrity rx2800 - i2 Manual del propietario

Manuales populares de Servidor de otras marcas

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Dell

Dell PowerEdge HS5610 Manual