HP D7171A - NetServer - LPr Manual de usuario
HP NetServer LC 2000
Pedestal to Rack Guide
HP Part Number 5969-2110
Printed November 1999
ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall not
be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied, reproduced,
or translated to another language without the prior written consent of
Hewlett-Packard Company.
Windows NT®, Windows 95®, and Windows 98®are registered trademarks of
Microsoft in the U.S. and other countries.
3M®is a registered trademark of Minnesota Mining and Manufacturing Company.
Torx®is a registered trademark of CamCar/Textron, Inc.
Tinnerman®is a registered trademark of Eaton/Tinnerman.
Hewlett-Packard Company
Network Server Division
Technical Communications MS 45SLE
10955 Tantau Avenue
Cupertino, California 95014 USA
© Copyright 1999, Hewlett-Packard Company.
Audience Assumptions
The guide is for the person who installs, administers, and troubleshoots LAN
servers. Hewlett-Packard Company assumes you are qualified in the servicing of
computer equipment and trained in recognizing hazards in products with
hazardous energy levels and are familiar with weight and stability precautions for
rack installations.
iii
Contents
1 Preparing the HP NetServer for Rack-Mounting ........................................ 1
Introduction ................................................................................................... 1
Tools Required.......................................................................................... 1
Removing the HP NetServer’s Top Cover and Pedestal................................. 2
Removing the Bezel .................................................................................. 3
Removing the Top Cover........................................................................... 4
Removing the Pedestal.............................................................................. 5
2 Rack Mounting the HP NetServer ............................................................... 7
Introduction ................................................................................................... 7
Tools Required.......................................................................................... 8
Safety Precautions.................................................................................... 9
Preparing the Rack...................................................................................... 10
HP NetServer Rack Mount Parts List....................................................... 10
Marking the Rack and Attaching Rack Nuts ............................................. 10
Attaching the Column Adapters and Slides.............................................. 13
Attach the Hinge Assembly and Catch Assembly..................................... 16
Attach the Mounting Handles................................................................... 17
Placing the HP NetServer in the Rack...................................................... 18
Attaching the Cable Management Arm..................................................... 22
Attaching the Front Bezel ........................................................................ 24
Continuing with the Rack Installation Process.............................................. 25
Index............................................................................................................... 27
1
1 Preparing the HP NetServer for
Rack-Mounting
Introduction
This chapter describes how to remove the top cover and the pedestal from the
HP NetServer LC.
WARNING Before removing the top cover, shut down the operating
system and disconnect the power cords and unplug telephone
cables. Disconnect the power cords to avoid exposure to
high energy levels that may cause burns when parts are
short-circuited by metal objects, such as tools or jewelry.
Disconnect telephone cables to avoid exposure to a shock
hazard from telephone ringing voltages.
Tools Required
l
An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist
strap.
Chapter 1 Preparing the HP NetServer for Rack-Mounting
2
Removing the HP NetServer’s Top Cover and
Pedestal
Use this procedure to remove the bezel, top cover, and pedestal from the pedestal
version of the HP NetServer LC 2000.
WARNING Do not operate the HP NetServer with its covers removed.
Always disconnect the power cord before removing any
covers, to avoid exposure to high energy levels that may cause
burns when parts are short-circuited bymetal objects such as
tools or jewelry. Disconnect any telephone cables to avoid
exposure to shock hazard from telephone ringing voltages.
CAUTION To prevent overheating, never operate the NetServer with its
cover removed. This includes the power supplies and Hot
Swap hard disks, which must be replaced or the opening
covered immediately (within 2 minutes).
1. If the HP NetServer is operating, log off all users and if necessary back-up
files.
2. Follow instructions in your network operating system (NOS)
documentation to gracefully shut down all networking software and
applications.
3. Press the power switch on the HP NetServer’s control panel when
prompted by the operating system.
Normally, this completes the power down procedure.
4. Disconnect the power cord from its power source.
Chapter 1 Preparing the HP NetServer for Rack-Mounting
3
Removing the Bezel
1. Pull the top of the bezel forward until it unsnaps.
2. Lift the entire bezel upward and away from the chassis. See Figure 1-1.
The bezel connects to the front of the HP NetServer chassis with two snap-in
connectors at the top front of the chassis and two metal tabs, which fit into
two slots on the bottom front of the chassis.
Figure 1-1. Removing the HP NetServer LC 2000 Bezel
CAUTION To prevent damage to the covers, support the cover as you
remove it from the HP NetServer. The NetServer’s covers can
be easily damaged.
Chapter 1 Preparing the HP NetServer for Rack-Mounting
4
Removing the Top Cover
1. Remove the single screw that secures the top cover to the front of the
NetServer.
2. Slide the top cover forward to disengage the mounting brackets.
3. Lift the top cover off (See Figure 1-2).
Screw Hole
Top Cover
Figure 1-2. Removing the Top Cover
Chapter 1 Preparing the HP NetServer for Rack-Mounting
5
Removing the Pedestal
The pedestal version of the HP NetServer LC 2000 mounts to an anti-tip pedestal,
which can be easily removed, if necessary.
NOTE The front bezel is shown removed, but the bezel may remain on
the chassis while removing the pedestal.
1. Disconnect all cables connected to the rear of the NetServer that would
limit its rotation before continuing.
2. Turn the NetServer over onto its top and pull up on the two tabs as shown
in Figure 1-3.
Figure 1-3. Removing the Pedestal
3. Slide the pedestal to the rear of the NetServer as shown in Figure 1-3.
Otros manuales para D7171A - NetServer - LPr
117
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Servidor de HP
HP
HP T5720 - Compaq Thin Client Manual de usuario
HP
HP Computer Parts Manual de usuario
HP
HP BL920s Gen8 Instrucciones de montaje
HP
HP ProLiant DL360 Generation 4 Manual
HP
HP Tc4100 - Server - 256 MB RAM Manual de usuario
HP
HP DL320s - ProLiant 9TB SATA Storage Server... Guía de instalación
HP
HP ProLiant SL160z Generation 6 (G6) Manual de usuario
HP
HP D5970A - NetServer - LCII Manual de usuario
HP
HP Cluster Platform Introduction v2010 Manual de referencia
HP
HP Tc2100 - Server - 128 MB RAM Manual técnico
HP
HP 2533t - Compaq Mobile Thin Client Manual de usuario
HP
HP Workstation zx6000 Hoja de especificaciones
HP
HP ProLiant DL385 G7 Manual
HP
HP Integrity Superdome 2 16-socket Manual de usuario
HP
HP T5720 - Compaq Thin Client Hoja de especificaciones
HP
HP ProLiant ML310 Generation 5p Instrucciones de funcionamiento y seguridad
HP
HP ProLiant DL385p Gen8 Manual de usuario
HP
HP ProLiant DL145 Manual
HP
HP T5145 - Thin Client - Tower Manual de operación y mantenimiento
HP
HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Manual de servicio
