HP 8572A Manual de usuario

User's Guide

HP 8572A EMI Receiver

ABCDE

HP P

art No. 08572-90003

Printed in USA April 1992

All manuals and user guides at all-guides.com

all-guides.com

Notice

The information contained in this document is sub ject to change

without notice.

Hewlett-Packard makes no warrantyofany kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and tness for a particular purpose. Hewlett-Packard

shall not b e liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing,

performance, or use of this material.

Restricted Rights Legend.

Use, duplication, or disclosure by the U.S. Government is sub ject to

restrictions as set forth in subparagraph (c) (1) (ii) of the Rights

in Technical Data and Computer Software clause at DFARS

252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c)

(2) of the Commercial Computer Software Restricted Rights clause at

AR 52.227-19 for other agencies.



All Righ

ts Reserv

ed. Reproduction, adaptation, or translation

without prior written permission is prohibited, except as allow

under the cop

yrigh

tla

ws.

1400 F

oun

tain Gro

arkw

, San

ta Rosa, CA 95403-1799, USA

All manuals and user guides at all-guides.com

Certification

Hewlett-Packard Company certies that this pro duct met its

published specications at the time of shipment from the factory.

Hewlett-Packard further certies that its calibration measurements

are traceable to the United States National Institute of Standards

and Technology, to the extent allowed by the Institute's calibration

facility, and to the calibration facilities of other International

Standards Organization members.

Warranty

This Hewlett-Packard instrument product is warranted against

defects in material and workmanship for a perio d of one year from

date of shipment. During the warranty p erio d, Hewlett-Packard

Company will, at its option, either repair or replace pro ducts which

prove to be defective.

For warranty service or repair, this product must be returned to a

service facilit

ydesignated b

yHewlett-P

ard. Buy

er shall prepa

shipping c

harges to Hewlett-P

ard and Hewlett-Pac

kard shall pa

shipping c

harges to return the pro duct to Buy

er. Ho

er, Buy

shall pa

yall shipping c

harges, duties, and taxes for pro ducts returned

to Hewlett-P

ard from another coun

try

Hewlett-P

ard w

arran

ts that its soft

are and rm

are designated

yHewlett-P

ard for use with an instrumen

twill execute

its programming instructions when properly installed on that

instrumen

t. Hewlett-P

ard do es not w

arran

tthat the op eration

of the instrumen

t, or soft

are, or rm

are will beunin

terrupted or

error-free.

Limit

tion of W

arranty

The foregoing w

arran

yshall not apply to defects resulting from

improp er or inadequate maintenance byBuyer, Buyer-supplied

software or interfacing, unauthorized mo dication or misuse,

op eration outside of the environmental specications for the

pro duct, or improp er site preparation or maintenance.

NO OTHER W

ARRANTY IS EXPRESSED OR IMPLIED.

HEWLETT-P

CKARD SPECIFICALL

Y DISCLAIMS THE

IMPLIED W

ARRANTIES OF MER

CHANTABILITY AND

FITNESS F

OR AP

ARTICULAR PURPOSE.

Exclusive Remedies

THE REMEDIES PR

OVIDED HEREIN ARE BUYER'S SOLE

AND EXCLUSIVE REMEDIES. HEWLETT-PACKARD SHALL

NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL,

INCIDENT

AL, OR CONSEQUENTIAL D

AMA

GES, WHETHER

BASED ON CONTRACT, TOR

T, OR ANY OTHER LEGAL

THEOR

iii

All manuals and user guides at all-guides.com

Assistance

Product maintenance agreements and other customer assistance

agreements are available for Hew lett-Packardproducts.

For any assistance, contact your nearest Hew lett-Packard Sales and

ServiceOce.

All manuals and user guides at all-guides.com

Safety Symbols

The following safety symbols are used throughout this manual.

Familiarize yourself with each of the symbols and its meaning before

op erating this instrument.

CAUTION

The

CAUTION

sign denotes a hazard. It calls attention to a

pro cedure which, if not correctly performed or adhered to, could

result in damage to or destruction of the pro duct or the user's

work. Do not pro ceed beyond a

CAUTION

sign until the indicated

conditions are fully understoo d and met.

WARNING

The

WARNING

sign denotes a hazard. It calls attention to a

procedure which, if not correctly performed or adhered to, could result

in injury to the user. Do not proceed beyond a

WARNING

sign until

the indicated conditions are fully understood and met.

DANGER

The

DANGER

sign denotes an imminent hazard to people. It warns

the reader of a procedure which, if not correctly performed or adhered

to, could result in injury or loss of life. Do not proceed bey

ond a

ANGER

sign until the indicated conditions are fully understood and

met.

All manuals and user guides at all-guides.com

General Safety Considerations

WARNING

The instructions in this document are for use by qualified personnel

only.Toavoid electrical shock, do not perform any servicing unless

you are qualified to do so.

The opening of covers or removal of parts is likely to expose

dangerous voltages. Disconnect the instrument from all voltage

sources while it is being opened.

The power cord is connected to internal capacitors that may remain

live for five seconds after disconnecting the plug from its power

supply.

This is a Safety Class 1 Product (provided with a protective earthing

ground incorporated in the power cord). The mains plug shall only

be inserted in a socket outlet provided with a protective earth

contact. Any interruption of the protective conductor inside or

outside of the instrument is lik

ely to mak

ethe instrument dangerous.

Intentional interruption is prohibited.

For continued protection against fire hazard, replace fuse only with

same type and ratings, (type nA/nV). The use of other fuses or

materials is prohibited.

ARNING

Before this instrument is switched on, mak

esure it has been

properly grounded through the protectiv

econductor of the ac po

cable to asock

et outlet pro

vided with protectiv

eearth contact.

Any interruption of the protectiv

e(grounding) conductor, inside or

outside the instrument, or disconnection of the protective earth

terminal can result in personal injury

Before this instrument is switched on, make sure its primary power

circuitry has been adapted to the voltage of the ac power source.

Failure to set the ac power input to the correct voltage could cause

damage to the instrument when the ac power cable is plugged in.

All manuals and user guides at all-guides.com

all-guides.com

In This Book

...

Chapter 1 How and when to calibrate your

EMI receiver system.

Chapter 2 How to perform op eration verication.

Chapter 3 How to set up your test equipment for op eration

verication.

Chapter 4 Howtomaketypical measurements with your

EMI receiver system.

Chapter 5 Howtomake measurements with downloadable

programs.

vii

All manuals and user guides at all-guides.com

Contents

1. Calibrating Your Receiver

When to Calibrate Your Receiver . . . . . . . . . 1-2

Calibrating Receiver INPUT 1 and INPUT 2 . . . 1-3

Calibrating Receiver INPUT 3 . . . . . . . . . . 1-5

Preselector Peaking for Receiver INPUT 3 . . . . . 1-7

Correcting Receiver INPUT 3 Using a Calibration

Table . . . . . . . . . . . . . . . . . . . 1-8

Manual Measurements Using Receiver INPUT 3 . 1-11

Automated Measurements Using Receiver INPUT 3 1-12

Spectrum Analyzer Corrected Mo de . . . . . . . 1-14

2. Operation V

erication

Step 1. Set up the hardw

are for op eration v

erication

testing .... . ..............2-2

Step 2. Load the soft

are ............2-3

Step 3. Select the EMI receiv

er system mo del ...2-5

Step 4. En

ter the EMI receiv

er system test information 2-6

Step 5. Cho ose the output destination for y

our test

results ...................2-7

Step 6. Select \T

est all mo del n

bers" ... . . . 2-8

Step 7. Select equipmen

tfrom the UUT Conguration

menu. . .................2-9

Step 8. Assign serial n

bers to all equipmen

t...2-10

Step 9. V

erify the test equipmen

t.. . . . . . . . 2-11

Step 10. Conrm the list of accessories . . . . . . 2-12

Step 11. Run the operation verication tests . . . . 2-13

Optional: Installing the software on an SRM or HFS

hard disk . . . . . . . . . . . . . . . . . . 2-15

Optional: Assigning the address type . . . . . . . 2-16

Optional: Selecting the EMI receiv

er system address 2-17

Optional: Adding option 049 ..... . .....2-18

Optional: Mo difying the temperature setting . . . 2-19

Optional: Mo difying the h

umidity setting . . . . .2-20

Optional: Selecting the line frequency . . . . . . . 2-21

Optional: Changing the default equipmen

t. . . . . 2-22

Optional: Entering p o

wer sensor calibration factors . 2-26

HP 8572A EMI Receiv

er User's Guide Contents-1

All manuals and user guides at all-guides.com

3. Test Descriptions

Calibrator Amplitude Accuracy . . . . . . . . . 3-2

Log Fidelity . . . . . . . . . . . . . . . . . . 3-5

Linear Fidelity. . . . . . . . . . . . . . . . . 3-7

Reference Level Switching Uncertainty . . . . . . 3-9

Receiver Calibration INPUT 1 . . . . . . . . . . 3-12

Amplitude Accy. INPUT 1 (10 dB AT and 0 dB AT) ,

20 Hz-9 kHz . . . . . . . . . . . . . . . . 3-15

Amplitude Accy. INPUT 1 (10 dB AT and 0 dB AT) 3-17

Disp. Average Noise INPUT 1 . . . . . . . . . . 3-19

Sensitivity INPUT 1, 20 Hz to 9 kHz . . . . . . . 3-21

Residual Responses INPUT 1 . . . . . . . . . . 3-23

Bandwidth Accuracy . . . . . . . . . . . . . . 3-25

Pulse Resp onse . . . . . . . . . . . . . . . . . 3-28

Calibration INPUT 2 . . . . . . . . . . . . . . 3-33

Amplitude Accy. INPUT 2 (10 dB AT and 0 dB AT) 3-36

Disp. Average Noise INPUT 2 . . . . . . . . . . 3-39

Residual Responses INPUT 2 . . . . . . . . . . 3-41

Amplitude Accy

. INPUT 3 . ..........3-43

Disp. Av

erage Noise INPUT 3,10 Hz RBW ....3-48

Residual Responses INPUT 3......... . 3-50

4. Making T

ypical Measuremen

esting for Ov

erload ..... . ........4-1

3dB Linearity Chec

k.............4-2

Narrowband/Broadband Signals .........4-2

Commercial Compliance Measuremen

ts ......4-5

Detector Selection ..... . ........4-5

Measuremen

t Examples ............4-9

CE03 (MIL-STD) Measuremen

t.........4-23

RE02 (MIL-STD) Measuremen

t.........4-26

CISPR 22 Measuremen

ts ...... . . . . . .4-28

5. Downloadable Program (DLP) Measurements

Example: Quasi-p eak measurements on broadband

signals, using a DLP . . . . . . . . . . . . . 5-1

Index

Contents-2 HP 8572A EMI Receiv

er User's Guide

All manuals and user guides at all-guides.com

Otros manuales para 8572A

Tabla de contenidos

Otros manuales de Receptor de HP

HP 8572A Manual de usuario

HP 8542E Manual de instalación y operación

HP 8530A Manual de usuario

HP 8542E Manual de usuario

HP X5400 Instrucciones de instalación y mantenimiento

HP x280n - MediaSmart Connect - Digital Multimedia... Manual de usuario

HP EN5000 Manual de instrucciones

HP x280n - MediaSmart Connect - Digital Multimedia... Manual de instalación y operación

HP 8530A Manual del propietario

HP EN5000 Manual de usuario

HP 3702B Manual de usuario

HP 83447A Manual

HP Hewlett-Packard Manual de usuario

HP EW5000 Hoja de instrucciones

HP x280n - MediaSmart Connect - Digital Multimedia... Manual de uso y mantenimiento

HP HP 8902A Manual de instrucciones

HP EN5000 Manual de usuario

HP EW5000 Instrucciones de montaje

HP 8530A Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario