HP D7171A - NetServer - LPr Manual de usuario

HP NetServer LH 3r, LH 4r,

LH 3000r, and LH 6000r

Installation Guide for

Compaq®4000/7000 Racks

HP Part Number 5969-5924

Printed in November 1999

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of anykind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or for incidental or consequential damages

in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, reproduced,

or translated to another language without the prior written consent of

Hewlett-Packard Company.

Compaq®is a registered trademark of Compaq Computer Corporation.

APC®is a registered trademark of American Power Conversion Corporation.

Hewlett-Packard Company

Network Server Division

Technical Marketing / MS 45S-LE

10955 Tantau Avenue

Cupertino, CA 95014 USA

Audience Assumptions

The user guide is for the person who installs, administers, and troubleshoots

network servers. Hewlett-Packard Company assumes you are qualified in the

servicing of computer equipment and trained in recognizing hazards in products

with hazardous energy levels.

iii

Contents

1 Introduction ................................................................................................. 1

HP NetServer – Compaq Rack Precautions................................................... 4

2 Overview...................................................................................................... 5

3 Installation................................................................................................... 7

Preparation.................................................................................................... 7

Marking the Installation Holes.................................................................... 7

Installing the Bar Nuts, Screws, and Cage Nuts......................................... 9

Mounting the Slides................................................................................. 10

Installing the NetServer ............................................................................... 12

Mounting the NetServer to the Slides....................................................... 12

Optional for HP NetServer LH 3000r and LH 6000r, Install Cable

Management Arm.................................................................................... 16

Installing the Recessed Mounting Brackets.............................................. 18

Relocating the Control Panel ................................................................... 19

Installing the Bezel .................................................................................. 22

4 Warranty and Support............................................................................... 23

Hardware Accessories Limited Warranty...................................................... 23

Hewlett-Packard Hardware Accessories .................................................. 23

Third-Party Hardware Products................................................................ 24

HP Repair and Telephone Support .............................................................. 24

Index............................................................................................................... 25

1 Introduction

This document describes how to mount an HP NetServer LH 3r, LH 4r, LH3000r,

or LH 6000r into a Compaq®model 4000- or 7000-series rack enclosure. Refer to

the documentation that came with the HP NetServer for instructions on adding

accessories to, and configuring the NetServer.

The HP NetServer LH 3r, LH 4r, LH3000r, or LH 6000r (the pedestal versions of

this NetServer) cannot be installed in a rack enclosure. If you want to convert a

pedestal version for installation in a rack enclosure, contact your HP Reseller for

information about the available conversion kit.

Pedestal and rack–optimized versions are shown in Figure 1-1.

Rack-Optimized VersionPedestal Version

Figure 1-1. Versions of the HP NetServer

Chapter 1 Introduction

WARNING To prevent the rack from tipping over and causing equipment

damage or bodily injury, be sure that the stabilizing, anti-tip

feature is installed on this rack enclosure see Figure 1-2.

WARNING To prevent the rack from tipping over and causing equipment

damage or bodily injury, do not extend more than one piece of

equipment at a time out of the front of the rack enclosure.

Be sure that the stabilizing, anti-tip feature is installed on the rack enclosure in

which you are installing the HP NetServer. This option consists of two "feet" at

the front of the base of the enclosure and, if you are installing this NetServer in a

single rack enclosure, two "feet" each on the left and right sides of the enclosure

see Figure 1-2.

Chapter 1 Introduction

Figure 1-2. Single Rack Enclosure with the Anti-Tip

Stabilizing Feature Installed

Chapter 1 Introduction

HP NetServer – Compaq Rack Precautions

CAUTION If this NetServer is not installed according to these

instructions, damage to the NetServer or accessories may

result. Damage due to improper installation is not covered by

the HP Warranty. Observe the precautions listed in this

section to maintain the NetServer’s reliability.

When installing this HP NetServer in a Compaq rack enclosure, certain

requirements must be addressed to assure that the needs of the NetServer are met.

This NetServer will meet the requirements designed for the NetServer if:

•The NetServer is installed in a Compaq model 4000- or 7000-series rack

enclosure. This NetServer is not supported in any other non-HP rack

enclosure.

•If you choose to use a door on this enclosure, only a Compaq model

4000- or 7000-series door may be used. No other door may be used. The

enclosure may then be used with the door open, closed, or removed.

•If you install a cable management arm, be sure to remove and discard the

rear door of the rack.

•Mass storage devices listed in the Tested Products List (located on the

HP NetServer Navigator CD-ROM) are used exclusively in the NetServer.

•Use HP rack accessories. (Note that HP rack accessories are not optimized

for Compaq rack enclosures.)

Compaq rack accessories have not been tested with HP NetServer

products, but components such as monitors, keyboards, switchboxes, and

PDUs often work.

•Use APC®uninterruptable power supplies (UPS) with HP NetServers.

APC offers mounting kits for Compaq rack enclosures.

This NetServer is not supported in a rack enclosure under circumstances other

than those listed above.

See the "Warranty and Support" section of this document for additional support

considerations.

2Overview

The steps required to install the NetServer in the rack are summarized below:

NOTE This is only a summary; detailed instructions are provided on the

following pages.

•Measure and mark the appropriate holes on all four rack columns.

•Install one bar nut on each of the four rack columns.

•Insert two cage nuts on each of the two front columns only.

•Attach the slides to the columns.

•Extend the slides.

•Remove power supply modules and hot-swap drives from the NetServer.

•Lift the NetServer onto the slides.

•Secure the NetServer to the slides.

•Remove the lifting handles from the NetServer.

•Reinstall the power supply modules and hot-swap drives.

•Push the NetServer back into the rack enclosure.

•For HP NetServer LH 3000r and LH 6000r, attach the optional cable

management arm.

•Install the recessed mounting brackets on the two front columns only.

•Relocate the control panel.

•Install the Compaq rack-compatible bezel.

Chapter 2 Overview

Terms used in this document are defined in the table below.

Term Definition

Bar nut Short, threaded bar used behind slide mounting flanges.

Used in place of individual nuts to mate with slide

mounting screws.

Bezel Removable plastic fascia panel that covers entire front of

the NetServer. This NetServer includes two bezels: one for

installation in HP rack enclosures, and one for installation

in Compaq 4000/7000 series rack enclosures.

Control Panel Display and buttons used to view NetServer status and

change system parameters.

EIA unit Industry standard measurement (1.75 inches / 44.45 mm),

consisting of three vertical mounting holes in a rack

column.

Cage nut Single nut designed to clip into the rack column and accept

a screw through the hole in the column.

Rack (rack chassis,

rack enclosure) The equipment enclosure in which the NetServer will be

installed. This document covers installation in a Compaq

4000/7000 series rack only.

Recessed mounting

brackets Two brackets (one tall, one short) that attach to the front of

the NetServer and the front rack columns to hold the

NetServer in the closed position.

Slide Extendible side bracket which is attached to the rack

chassis columns on which the NetServer is mounted.

Consists of stationary member, and an extendible member

see Figure 3-3. Allows access to the NetServer after it is

installed in the rack chassis.

Slide mounting flange Mounting flange located at either end of the slide see

Figure 3-3.

Otros manuales para D7171A - NetServer - LPr

117

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de HP

HP Proliant DL580 Manual de usuario

HP ProCurve 6600-48G-4XG Manual de usuario

HP 355 Manual de usuario

HP D7171A - NetServer - LPr Manual de usuario

HP 11000 G2 series Manual de usuario

HP Z600 - Workstation - 6 GB RAM Manual de usuario

HP J1530C Manual de usuario

HP AT-BT10 Manual de usuario

HP Integrated Work Center Stand Instrucciones de uso

HP Model 745 - VME Workstation Manual de usuario

HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Manual de usuario

HP MCS 5042 Manual de usuario

HP RP9 Compact Stand Manual de usuario

HP Tc4100 - Server - 256 MB RAM Manual de usuario

HP 245161-B22 - 10642 42U Rack Shock Pallet Manual de usuario

HP StorageWorks SSL1016 Manual de usuario

HP A4838A Manual de usuario

HP 11000 G2 series Manual de usuario

HP LaserJet Enterprise 600 Manual de usuario

HP AT-BT10 Manual de usuario

HP BT861AA Manual de usuario

HP 245161-B22 - 10642 42U Rack Shock Pallet Instrucciones de uso

HP HP 10000 G2 Series Manual de usuario

HP TS5220 Guía de instalación

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario