HP Vectra VEi 7 Manual de usuario
Olicom OC-3137 Token Ring 16/4
PCI Adapter
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft
Corporation.
MMXTM is a trademark of Intel Corporation.
Pentium® is a registered trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
©1999 Hewlett Packard Company
General information to read before installing
General information to read before installing
On all systems: before installing LAN card, go into Bios setup and set PnP OS field to NO.
• How to change LAN card configuration if needed (Advanced users only)
This is a general advisory on how to forcibly modify resources for ISA and PCI network
cards.
ISA cards:
• For ISA network adapters, start the configuration tool provided in driver
kit (See install documentation)
• Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu-
sion > reserve an IRQ for the adapter.
PCI cards:
• For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA
IRQ Resource Exclusion > reserve the IRQ for Legacy ISA.
• ISA cards can’t use IRQ9
• IRQ 9 is reported as being used by ACPI during POST. This is due to ISA’s
inability to share IRQs.
• Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this:
1Install the NIC then power up the system.
2Press F2 to go to CMOS setup.
3Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation
section)
4Save the configuration settings and boot to the applicable OS.
5Follow installation steps.
Sound conflict under Win 95 on VLi8 only
• On VLi8, LAN cards cause an IRQ conflict with the embedded sound de-
vice under Win95.
• To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this:
1Install the NIC then power up the system
General information to read before installing
2Press F2 to go to CMOS setup.
3Set PNP OS to NO and reserve IRQ 5.
4Save settings and boot to applicable OS.
1 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95 SR2.5
1 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 3.51 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Olicom 3137 Token Ring 16/4 PCI adapter and drivers disk version 29.4.0.
• Driver: OCTOK16.SYS, version 4.16
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT 3.51 Server system that supports NetBEUI,
NWLink IPX/SPX Compatible Transport, and NWLink NetBIOS network
protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Olicom 3137 Token Ring 16/4
PCI card into a PCI slot.
2Connect network cable media to the Olicom 3137 Token Ring 16/4 PCI
card.
3Power on the machine and boot to Windows 95.
4When Windows 95 restarts, a message will appear to indicate that new
hardware has been found.
5Windows 95 will recognize a “Olicom 3137 Token Ring 16/4 PCI Adapter”.
6Specify your Computer name, Workgroup name, and Computer
Description, and click on “Close”.
7When prompted, set the path to your Windows 95 files and click on “OK”.
8When prompted, click on “Yes” to reboot your machine.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 09 03 10
I/O Address 1000 DCC0 E400
2 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95 SR2.5
2 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 4.0 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Olicom 3137 Token Ring 16/4 PCI adapter and driver disk version 29.4.0.
• Driver: OCTOK16.SYS, version 4.16
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink
IPX/SPX Compatible Transport, and NWLink NetBIOS network protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Olicom 3137 Token Ring 16/4
PCI card into a PCI slot.
2Connect network cable media to the Olicom 3137 Token Ring 16/4 PCI
card.
3Power on the machine and boot to Windows 95.
4When Windows 95 restarts, a message will appear to indicate that new
hardware has been found.
5Windows 95 will recognize a “Olicom 3137 Token Ring 16/4 PCI Adapter”.
6Specify your Computer name, Workgroup name, and Computer
Description, and click on “Close”.
7When prompted, set the path to your Windows 95 files and click on “OK”.
8When prompted, click on “Yes” to reboot your machine.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 11
I/O Address 1000 DCC0 E400
3 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95 SR2.5
3 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95
SR2.5
Connecting to a Novell
NetWare 3.12 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Olicom 3137 Token Ring 16/4 PCI adapter and drivers disk version 29.4.0.
• Driver: OCTOK16.SYS, version 4.16
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 3.12 Server system that supports IPX network protocol.
• Novell Client for Windows 95 v2.5 installation media.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Olicom 3137 Token Ring 16/4
PCI card into a PCI slot.
2Connect network cable media to the Olicom 3137 Token Ring 16/4 PCI
card.
3Power on the machine and boot to Windows 95.
4When Windows 95 restarts, a message will appear to indicate that new
hardware has been found.
5Windows 95 will recognize a “Olicom 3137 Token Ring 16/4 PCI Adapter”.
6Specify your Computer name, Workgroup name, and Computer
Description, and click on “Close”.
7When prompted, set the path to your Windows 95 files and click on “OK”.
8When prompted, click on “Yes” to reboot your machine.
9From the location of the “Novell Client for Windows 95 v.2.5” installation
files, execute “Setup.exe”.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1000 DCC0 E400
3 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Connecting to a Novell NetWare 3.12 Server
10 Click on “Yes” to accept the License Agreement.
11 Select “Custom” installation and click on “Next”.
12 Select “Bindery (NetWare 3.x)” and click on “Next”.
13 Click on “Install” to start the installation.
14 Click on “Yes” to set the Preferred Server. (If you do not have the
required information, contact your network administrator).
15 Click on “Reboot” to complete the installation.
4 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95 SR2.5
4 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Microsoft Windows 95
SR2.5
Connecting to a Novell
NetWare 4.11 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Olicom 3137 Token Ring 16/4 PCI adapter and drivers disk version 29.4.0.
• Driver: OCTOK16.SYS, version 4.16
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 4.11 Server system that supports IPX network protocol.
• Novell Client for Windows 95 v2.5 installation media.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Olicom 3137 Token Ring 16/4
PCI card into a PCI slot.
2Connect network cable media to the Olicom 3137 Token Ring 16/4 PCI
card.
3Power on the machine and boot to Windows 95.
4When Windows 95 restarts, a message will appear to indicate that new
hardware has been found.
5Windows 95 will recognize a “Olicom 3137 Token Ring 16/4 PCI Adapter”.
6Specify your Computer name, Workgroup name, and Computer
Description, and click on “Close”.
7When prompted, set the path to your Windows 95 files and click on “OK”.
8When prompted, click on “Yes” to reboot your machine.
9From the location of the “Novell Client for Windows 95 v.2.5” installation
files, execute “Setup.exe”.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 11
I/O Address 1000 DCC0 E400
4 Installing the Olicom OC-3137 Token Ring 16/4 PCI Adapter
Connecting to a Novell NetWare 4.11 Server
10 Click on “Yes” to accept the License Agreement.
11 Select “Custom” installation and click on “Next”.
12 Select “NDIS (NetWare 4.x or higher)” and click on “Next”.
13 Click on “Install” to start the installation.
14 Click on “Yes” to set the Preferred Tree, Server, etc. (If you do not have
the required information, contact your network administrator).
15 Click on “Reboot” to complete the installation.
Otros manuales para Vectra VEi 7
7
Este manual sirve para los siguientes modelos
2
Otros manuales de Tarjeta PCI de HP
HP
HP NC375T Manual de usuario
HP
HP NC1020 Instrucciones de uso
HP
HP Vectra VL6 7 Manual de usuario
HP
HP Vectra VEC 7 Manual de usuario
HP
HP StorageWorks fca2384 Manual de usuario
HP
HP Thunderbolt 3 Manual de usuario
HP
HP Vectra VL410 Manual de usuario
HP
HP NC570C Manual de usuario
HP
HP NC150T Manual de usuario
HP
HP Edgeline EL1000 Manual de usuario
HP
HP Vectra VE6 8 Manual de usuario
HP
HP AB465A Manual de usuario
HP
HP A7173A Manual de usuario
HP
HP 435508-B21 Instrucciones de uso
HP
HP VL600 - Vectra - 128 MB RAM Manual de usuario
HP
HP Compaq Pro 6305 Manual de usuario
HP
HP Vectra VEi 7 Manual de usuario
HP
HP 04H8095 Manual de usuario
HP
HP PCIe 2-Port 10GbE Manual de usuario
HP
HP FX 3500 Guía de instalación
Manuales populares de Tarjeta PCI de otras marcas
Belkin
Belkin F5D7000F Manual de usuario
Pericom
Pericom PI7C7100 Manual de usuario
ADLINK Technology
ADLINK Technology cPCI-3548 Manual de usuario
Digium
Digium TE200 Series Manual de usuario
Allo.com
Allo.com 2nd Gen E1/T1/J1 Manual de usuario
Western Digital
Western Digital FireWire PCI Adapter Manual de usuario