HP Vectra VEC 7 Manual de usuario

Etherlink III PCI Network Interface

Card (10BT)

3C590-TPO

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.1A.

DOS ODI - File Name: EL59X.DOS Size: 27KB Date: 10/04/96

• DOS and MS-Windows for Workgroups 3.11 media.

• Novell Netware server 3.12 that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• Network Driver Optimization Normal

• Full Duplex Disabled

• Boot PROM Disabled

• Media Type 10BASE-T

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and allow it to boot to a DOS prompt.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C59XCFG.EXE.

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address FCCO (PCI) FCC0h (PCI) DC00h (PCI)

Interrupt Request

Level

10 (PCI) 9 (PCI) 10 (PCI)

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

6Remove the 3com cards driver diskette and insert Netware client for DOS

and MS-Windows disk 1.

If you are using a Vectra VL7 or VE7/VE8, follow the instructions below to

complete the installation. If you are using a VL8, go directly to step 7.

aExecute INSTALL.EXE.

bSpecify the settings as listed below:

• C:\NWCLIENT

•Yes

• C:\WINDOWS

•No

• 3Com Fast Etherlink/Etherlink III Bus Master

cUnder the heading "Select the driver for your network board", insert

the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\

CLIENT." (If you have an HP preloaded HDD, set path to "C:\Masters\

LanDrv\3C590\NETWARE\CLIENT\)

dPress "Enter" to continue the installation.

eWhen prompted, insert the corresponding disks to complete file trans-

fer and driver installation.

fWhen the install utility is finished, press <CRTL><ALT><DEL> to

restart the machine.

gAfter Windows loads, open the "NETWORK" folder, double-click the

"NETWORK SETUP" icon.

hSelect "Networks" and verify that "Novell Netware (Workstation Shell

4.0 and above)" is selected under "Install Windows support for the

following network only:"

iSelect "OK" twice, and the installation is complete.

7Execute INST_DOS.EXE and enter Yes to accept the agreement.

8Accept the default products by pressing Enter, and then press “F10” to

continue.

9Select 16-bit LAN Drivers and hit the Enter key.

10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER”

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

and hit enter.

11 Insert the 3COM Etherlink 3C590 Ethernet card and drivers disk, set the

path to “A:\NETWARE\CLIENT\” and press enter.

12 Select “3Com Fast Etherlink / Etherlink III Bus Master Family” and press

enter.

13 Accept the default settings, press “F10” to continue, and verify the

following entries for the “Installation Configuration Summary”:

❒YES

❒C:\NOVELL\CLIENT32

❒C:\WINDOWS

❒16-bit LAN drivers

❒3Com Fast Etherlink / Etherlink III Bus Master Family

14 Press “F10” to save and continue.

15 When prompted, insert the corresponding disks to complete file transfer

and driver installation.

16 When the install utility is finished, press <CRTL><ALT><DEL> to restart

the machine.

17 After windows loads, open the “NETWORK” folder, double-click the

“NETWORK SETUP” icon.

18 Select “Networks”, and verify that “Novell Netware (Workstation Shell 4.0

and above)” is listed under “Install Windows support for the following

network only:” and click on “OK.”

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

Windows 95 SR2 Requirements

• HP Vectra with Windows 95 SR2 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.1a.

• File Name: EL59X.VXD Size: 38KB Date: 1/27/97

Driver for Vectra VE7/VE8: Windows 95 Embedded

• Windows 95 SR2 media (If you have an HP preloaded HDD, the media is

located at C:\Masters\Win95\System\Cabs\)

• Novell Netrware 3.12 server that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

Device Configuration

• Network Driver Optimization Normal

• Full Duplex Disabled

• Boot PROM Disabled

• Media Type 10BASE-T

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C59XCFG.EXE.

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

6Remove the 3com cards driver diskette and restart the machine.

7Windows 95 SR2 should automatically recognize the 3COM 3C590

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address FCC0h (PCI) FCE0h (PCI) DC00h (PCI)

Interrupt Request

Level

10 (PCI) 9 (PCI) 10 (PCI)

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

ethernet card

8When prompted, click on “OK” to continue.

9Enter “Computer Name”, “Workgroup”, and “Computer Description” data

and then open the “Configuration” folder.

10 In the “Configuration” folder, click on “Add”, then click on “Protocol” and

click on “Add” once again.

11 Listed under “Manufacturers”, select “Microsoft”, then select “TCP/IP”

under “Network Protocols:” and click on “OK.”

12 In the “Network” window, click on “Close” to continue the installation.

13 After files copy, you will be asked to restart your computer. Click on

“Yes.”

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

2 Connecting to a Netware 4.11 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.1a.

DOS ODI -

Vectra VL8 Driver File Name: 3C59X.COM Size: 55KB Date:10/04/96

• Vectra VL7 and VE7/VE8 Driver File Name: EL59X.DOS Size:27KB

Date: 10/04/96

• DOS and MS-Windows for Workgroups 3.11 media.

• Novell Netware server 4.1 that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• Network Driver Optimization Normal

• Full Duplex Disabled

• Boot PROM Disabled

• Media Type 10BASE-T

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and allow it to boot to a DOS prompt.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C59XCFG.EXE.

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address FCC0h (PCI) FCC0h (PCI) DC00h (PCI)

Interrupt Request

Level

10 (PCI) 9 (PCI) 10 (PCI)

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

6Remove the 3com cards driver diskette and insert Netware client for DOS

and MS-Windows disk 1.

If you are using a Vectra VL8, go directly to step 7.

If you are using a VL7 or VE7/VE8, follow the instructions below to

complete the installation.

aExecute INSTALL.EXE.

bSpecify the settings as listed below:

• C:\NWCLIENT

•Yes

• C:\WINDOWS

•No

• 3Com Fast Etherlink/Etherlink III Bus Master

cUnder the heading "Select the driver for your network board", insert

the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\CLI-

ENT." (If you have an HP preloaded HDD, set path to "C:\Masters\Lan-

Drv\3C590\NETWARE\CLIENT\)

dPress "Enter" to continue the installation.

eWhen prompted, insert the corresponding disks to complete file trans-

fer and driver installation.

fWhen the install utility is finished, press <CRTL><ALT><DEL> to re-

start the machine.

gAfter windows loads, open the "NETWORK" folder, double-click the

"NETWORK SETUP" icon.

hSelect "Networks" and verify that "Novell Netware (Workstation Shell

4.0 and above)" is selected under "Install Windows support for the fol-

lowing network only:"

iSelect "OK" twice, and the installation is complete.

7Execute INST_DOS.EXE and enter Yes to accept the agreement.

Otros manuales para Vectra VEC 7

Este manual sirve para los siguientes modelos

Otros manuales de Tarjeta PCI de HP

HP AB465A Manual de usuario

HP 4X - DDR InfiniBand Mezzanine HCA Hoja de instrucciones

HP 673642-B21 Manual de usuario

HP Vectra VL6 6 Manual de usuario

HP Compaq Pro 6305 Manual de usuario

HP Vectra VEi 7 Manual de usuario

HP A7173A Manual de usuario

HP NC375T Manual de usuario

HP Vectra VL6 7 Manual de usuario

HP IEEE-1394b Manual de usuario

HP Xw4600 - Workstation - 2 GB RAM Manual de usuario

HP Vectra VEi 7 Manual de usuario

HP Model 748 - VME Workstation Manual de usuario

HP VL600 - Vectra - 128 MB RAM Manual de usuario

HP Vectra VE6 8 Manual de usuario

HP FX 3500 Guía de instalación

HP A6826A Cómo utilizar

HP FC HBAs Guía de instalación

HP NC570C Manual de usuario

HP NC380T Instrucciones de uso

HP 04H8095 Manual de usuario

HP Vectra VL410 Manual de usuario

HP Thunderbolt 3 Manual de usuario

HP Edgeline EL1000 Manual de usuario

Manuales populares de Tarjeta PCI de otras marcas

ERMA

ERMA SSI 1417 Manual de usuario

SIIG

SIIG CyberSerial Dual PCI Instrucciones de montaje

Moxa Technologies

Moxa Technologies CP-102E Manual de usuario

I-Bus

I-Bus IBC2602 Manual de usuario

Exsys

Exsys EX-60102 Manual de usuario

Chelsio Communications

Chelsio Communications T5 Series Manual de usuario

Conrad Electronic

Conrad Electronic 97 46 71 Manual de usuario

Micro Innovations

Micro Innovations USB650A Manual de usuario

KTI Networks

KTI Networks KF-310 Manual de usuario

Asus

Asus SpaceLink WL230 Manual de usuario

SIIG

SIIG SC2475 Manual de usuario

TRENDnet

TRENDnet TEW-703PI Manual de usuario

Belkin

Belkin F5D7000F Manual de usuario

Pericom

Pericom PI7C7100 Manual de usuario

ADLINK Technology

ADLINK Technology cPCI-3548 Manual de usuario

Digium

Digium TE200 Series Manual de usuario

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manual de usuario

Western Digital

Western Digital FireWire PCI Adapter Manual de usuario