HP 2133 Mini-Note Manual de usuario

MultiBoot

User Guide

Development Company, L.P.

The information contained herein is subject

to change without notice. The only

warranties for HP products and services are

set forth in the express warranty statements

accompanying such products and services.

Nothing herein should be construed as

constituting an additional warranty. HP shall

not be liable for technical or editorial errors

or omissions contained herein.

Third Edition: June 2007

First Edition: March 2006

Document Part Number: 449434-001

Product notice

This user guide describes features that are common to most models. Some features may not be

available on your computer.

iii

iv Product notice

Table of contents

1 About the boot device order

2 Enabling boot devices in Computer Setup

3 Considering boot order changes

4 Choosing MultiBoot preferences

Setting a new boot order in Computer Setup ...................................................................................... 6

Dynamically choosing a boot device using the F9 prompt ................................................................... 7

Setting a MultiBoot Express prompt .................................................................................................... 8

Entering MultiBoot Express preferences .............................................................................................. 9

Index ................................................................................................................................................................... 10

1 About the boot device order

As the computer starts, the system attempts to boot from enabled boot devices. The MultiBoot utility,

which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices

can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices.

Boot devices contain bootable media or files that the computer needs to start and operate properly.

NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the

boot order.

The factory setting is for the computer to select the boot device by searching enabled boot devices and

drive bay locations in the following order:

NOTE: Some of the boot devices and drive bay locations listed may not be supported on your

computer.

●MultiBay or optical drive

●Internal hard drive

●USB floppy

●USB diskette on key

●USB CD-ROM

●USB SuperDisk

●USB hard drive

●Network controller

You can change the order in which the computer searches for a boot device by changing the boot order

in Computer Setup. You can also press f9 while the “F9 = Boot device menu” message is displayed in

the lower-left corner of the screen when the computer starts up. Pressing f9 displays a menu that shows

the current boot devices and allows you to select a boot device. Or, you can use MultiBoot Express to

set the computer to prompt you for a boot location each time the computer turns on or restarts.

If MultiBoot is disabled, the computer uses a fixed boot order that consists of first searching for a drive

A boot device. If none is found, the computer looks for a drive C boot device. Drive A boot devices

include optical drives and diskette drives. Drive C boot devices include optical drives and hard drives.

The NIC does not have an assigned drive letter.

NOTE: An optical drive (such as a CD-ROM drive) can boot either as drive A or drive C, depending

on the format of the boot CD.

The following list describes the factory setting for boot order in which drive letters A and C are assigned

when MultiBoot is disabled. (The actual order varies by configuration.)

●Boot order for drive A boot devices:

1. Optical drive in an optional docking device or in an optional external MultiBay that contains a

disc formatted as drive A

2. Optical drive in the internal MultiBay (select models only) that contains a disc formatted as

drive A

3. Diskette drive in an optional docking device or in an optional external MultiBay

●Boot order for drive C boot devices:

1. Optical drive in an optional docking device or in an optional external MultiBay that contains a

disc formatted as drive C

2. Optical drive in the internal MultiBay (select models only) that contains a disc formatted as

drive C

3. Hard drive in the computer hard drive bay

4. Hard drive in an optional docking device or in an optional external MultiBay

NOTE: Because no drive letter is associated with the NIC, changing the boot order of a NIC does not

affect the drive letters of the other devices.

2 Chapter 1 About the boot device order

2 Enabling boot devices in Computer

Setup

The computer will boot to a USB device or a NIC device only if the device has first been enabled in

Computer Setup.

To enable a USB device or a NIC device as a boot device, follow these steps:

1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the

"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.

2. To enable bootable media in USB drives or in drives inserted into an optional docking device (select

models only), use the arrow keys to select System Configuration > Device Configurations, and

then press enter. Use the arrow keys to select Enable in the USB legacy support field.

NOTE: The USB Port option must be enabled in order to use USB legacy support. It is enabled

at the factory. To disable or reenable this option, select System Configuration >Port Options.

– or –

To enable a NIC device, use the arrow keys to select System Configuration > Boot Options,

and then press enter. Use the arrow keys to select Enable in the Internal network adapter

boot field.

3. To save your preferences and exit Computer Setup, use the arrow keys to select File > Save

Changes and Exit. Then follow the instructions on the screen.

Your preferences go into effect when the computer restarts.

NOTE: To connect a NIC to a Preboot eXecution Environment (PXE) or Remote Program Load (RPL)

server without using MultiBoot, quickly press f12 when the “Network Service Boot” message appears

in the lower-right corner of the screen (select models only).

3 Considering boot order changes

Before changing the boot order, note the following considerations:

●When the computer restarts after the boot order has been changed, the computer attempts to start

using the new boot order.

●If there is more than one type of boot device, the computer attempts to boot using the first of each

type of boot device (except for optical devices). For example, if the computer is connected to an

optional docking device (select models only) that contains a hard drive, this hard drive will be shown

in the boot order as a USB hard drive. If the system attempts to boot from this USB hard drive and

fails, it will not attempt to boot to the hard drive in the hard drive bay. Instead, it will try to boot to

the next type of device in the boot order. However, if there are 2 optical devices, and the first optical

device does not boot (either because it does not contain media or the media is not a boot disc),

the system will try to boot to the second optical device.

●Changing the boot order also changes the logical drive designations. For example, if you start up

from a CD-ROM drive with a disc formatted as drive C, that CD-ROM drive becomes drive C and

the hard drive in the hard drive bay becomes drive D.

●The computer will boot from a NIC device only if the device has been enabled in the Built-In Device

Options menu of Computer Setup and if booting from the device has been enabled in the Boot

Options menu of Computer Setup. Booting from a NIC does not affect logical drive designations

because no drive letter is associated with the NIC.

●Drives in an optional docking device (select models only) are treated like external USB devices in

the boot order.

4 Chapter 3 Considering boot order changes

Otros manuales para 2133 Mini-Note

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Computadora portátil de HP

HP 2530p - EliteBook - Core 2 Duo 2.13 GHz Manual de usuario

HP EliteBook 850 G6 Instrucciones de montaje

HP OmniBook XE Manual de usuario

HP Pavilion DV5t-2100 Manual

HP Spectre x360 Convertible 15-bl131ng Manual de usuario

HP mt45 Manual

HP Compaq Mini CQ10 Manual

HP Pavilion DV6 Series Manual

HP ZBook 14u G6 Manual de usuario

HP ZBook 15 G2 Mobile Workstation Manual

HP Pavilion TX1340EA Manual de usuario

HP 16-b0 Series Manual

HP ENVY 13-ad016nc Manual de usuario

HP Elite Dragonfly 13.5 inch Chromebook Manual

HP ENVY 14 Manual

HP Compaq tc4400 Manual de usuario

HP OmniBook 6000 Manual de usuario

HP EliteBook 820 G2 Instrucciones de instalación

HP Chromebook 11 G3 Instrucciones de uso

HP ProBook 6360b Manual

HP 15-bs0 Series Manual

HP EliteBook 2540P Manual

HP Compaq Notebook Manual de usuario

HP Compaq Presario V2000 Series Instrucciones de montaje

Manuales populares de Computadora portátil de otras marcas

Velocity

Velocity NoteMagix M10 Manual de usuario

Dell

Dell Alienware 17 R2 Manual de usuario

Toshiba

Toshiba A105-S2236 Manual de usuario

Winbook

Winbook LM Manual de usuario

Dell

Dell Inspiron 1464 Manual de usuario

Dell

Dell Inspiron 15R 5537 Manual de usuario

Dell

Dell Latitude ATG D620 Manual de usuario

Sony

Sony VAIO PCG-FX270 Manual de usuario

Dell

Dell Latitude 7310 Manual de usuario

Dell

Dell Precision GU806 Manual de usuario

Sony

Sony VAIO PCG-R505JLK Manual de usuario

Lenovo

Lenovo THINKPAD X32 Manual de usuario

Toshiba

Toshiba mini NB300 Manual de usuario

Lenovo

Lenovo ThinkPad X201 Tablet Manual

Lenovo

Lenovo THINKPAD X31 Manual

Sony

Sony VGN-T240P VAIO Manual de usuario

Compaq

Compaq Armada E700 Series Manual de usuario

Fujitsu

Fujitsu Lifebook A6230 Manual de usuario