HP Visualize b1000 Manual

HP VISUALIZE B Class and C Class UNIX®

Workstations

Parts Replacement Guide

Manufacturing Part Number: A4985-90036

Edition E0100

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not

furnished by Hewlett-Packard.

this document may be photocopied, reproduced or translated to another language without the prior written

consent of Hewlett-Packard Company.

Hewlett-Packard Warranty Statement

Refer to Warranty & Support for your HP Workstation for warranty terms applicable to your Hewlett-Packard

product and replacement parts.

Restricted Rights Legend

Use, duplication, or disclosure by the U.S. Government Department of Defense is subject to restrictions as set

forth in paragraph (b)(3)(ii) of the Rights in Technical Data and Software clause in DFARS 252.227.7013.

UNIX is a registered trademark in the United States of America and other countries, licensed exclusively

through X/Open Company Limited.

This software and documentation is based in part on the Fourth Berkeley Software Distribution under license

from the Regents of University of California.

Contents

1. Getting Started

Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Electrostatic Discharge (ESD) Precautions . . . . . . . . . . . . . . . . . . . . . .5

Replacement Part Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Safely Powering Down the B Class and C Class Workstation . . . . . . . . .7

Product Exploded Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2. Parts Removal and Replacement

Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Removing the Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . .10

Replacing the Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . .11

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Removing the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Replacing the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Removing the Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Replacing the Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Removing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Memory Card(s) DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Removing and Replacing DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Removing PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Replacing PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

CD ROM Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Contents

Removing the CD ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Replacing the CD ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Removing the Front-Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Replacing the Front-Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Removing the Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Hard Disk Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Removing the Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Putting a Disk Drive into its Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Replacing the Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

I/O Fan and Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Removing the I/O Fan and Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Removing and Replacing the Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Removing and Replacing the Speaker . . . . . . . . . . . . . . . . . . . . . . . . . 37

Replacing the Fan and Speaker Bracket . . . . . . . . . . . . . . . . . . . . . . . 37

Removing and Replacing the System Board. . . . . . . . . . . . . . . . . . . . . . 38

Disconnecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Removing the old System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Replacing the System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Real Time Clock (RTC) Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Removing the Real Time Clock (RTC) Module . . . . . . . . . . . . . . . . . . 42

Replacing the Real Time (RTC) Module . . . . . . . . . . . . . . . . . . . . . . . 43

Removing and Replacing the System Board Cooling Fans . . . . . . . . . . 44

Replacing the System Board Cooling Fans . . . . . . . . . . . . . . . . . . . . . 45

3. Wrapping Up

Verifying System Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Returning the Defective Exchange Assembly . . . . . . . . . . . . . . . . . . . 47

1Getting Started

The following important information must be adhered to for proper removal and

replacement of all Hewlett-Packard parts.

Safety Warnings

WARNING Removing the device cover may expose sharp edges in the equipment

chassis. To avoid injury, use care when installing customer add-on

devices.

NOTE Before performing removal/replacement procedures, position the workstation

on a cushioned ﬂat, stable surface, such as a table top or workbench.

NOTE Installing the recommended HP replacement part in your B Class and C

Class workstation does not affect the regulatory and safety classiﬁcations or

approvals listed in the original owner’s guide.

Electrostatic Discharge (ESD) Precautions

To prevent damage to the B Class and C Class workstation, observe all of the following

ESD precautions while performing removal and replacement procedures:

• Remove all ESD-generating materials from the work area in which you will remove and

replace the workstation ﬁeld replaceable unit(s).

• Open the ESD materials provided with the replacement part kit. Unfold the black

conductive sheeting (antistatic mat) and place it under a corner of the workstation.

• Wear a static strap to ensure that any accumulated electrostatic charge is discharged

from your body to ground. Attach the static-grounding wrist strap by following the

instructions on the package. Attach the sticky end of the wrist strap to bare metal on

the rear panel of the workstation.

• Connect all equipment together, including the static-free mat, static strap, clips

attached to the wrist strap, nodes, and peripheral units.

• Keep uninstalled printed circuit boards in their protective antistatic bags.

• Once you have removed printed circuit boards from their protective antistatic bags,

handle the printed circuit boards by their edges only.

6Chapter1

Getting Started

Replacement Part Kit Contents

Take a moment to verify that your kit contains the following contents:

• The replacement part.

• Part Number: A3024-80004, Electrostatic Discharge (ESD) materials

• Removal/Replacement Instructions

If you are missing any part or any documentation, please call your designated service

representative.

Required Tools

You will need the following tools for removal/replacement procedures:

• T-10 and/or T-15 Torx drivers

• Light-duty ﬂat-blade screwdriver with a 150mm (6-inch) blade

• Needle-nosed pliers

• ESD materials

Chapter 1 7

Getting Started

Safely Powering Down the B Class and C Class Workstation

You must complete the following steps before performing any of the removal and

replacement procedures:

NOTE Remove any accessory bag(s) and their black tab screws, if present, from the

rear of the workstation.

1. Shut down the workstation by executing “shutdown -h” as user root. This ensures

that all programs are terminated and all data is saved before switching the power off.

Power down the workstation by simply pressing the power switch on the front panel.

Power off the monitor and any attached peripheral devices.

2. After 30 seconds, unplug the workstation’s power cord and all peripheral devices from

AC power outlets. Before attempting to move the workstation to a disassembly area,

disconnect all peripherals from the back of the system.

3. Place the workstation on a ﬂat, stable surface, such as a tabletop or ﬂoor. To protect

against scratches, remove miscellaneous debris from the work surface.

8Chapter1

Getting Started

Product Exploded Diagram

Refer to the ﬁgure below for a basic parts overview of the B Class and C Class workstation.

Figure 1-1. Exploded View

Chassis

Front-Panel Display

Hard Disk Tray

CD Drive Tray

Floppy Drive Tray

System Board

DIMMs (Memory)

Memory Fan

Side Panel

Power

System-Board Fans

I/O Fan/Speaker Bracket

Air Divider

I/O Card

Speaker

I/O Fan

Supply

Retainer Clip

2Parts Removal and Replacement

This chapter describes how to remove and replace the various parts in the B Class and C

Class workstations.

10 Chapter2

Parts Removal and Replacement

Terminators and Cables

This section describes how to remove and replace the Terminators and Cables

Removing the Terminators and Cables

1. After powering down the workstation as described in the “Getting Started” chapter,

unplug the power cable from the back of the workstation. To avoid ESD damage to

components, carefully follow the ESD procedures (also described in the “Getting

Started” chapter).

2. Remove the two SCSI terminators from the back of the machine, as shown below. Or, if

you have already replaced either or both of the terminators with cables to external

peripheral devices, remove those cables., LAN cable, USB cables, and any other cables

from the back of the workstation.

Figure 2-1. Removing all Terminators and Cables

1. Remove the cables from the USB Clip from the back of the Workstation.

SCSI Terminators

Audio In/Out Ports

Parallel Port

LAN Port

USB Ports

Serial Ports

Power Plug

Otros manuales para Visualize b1000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de HP

HP Omni 220-1200 Manual de usuario

HP Compaq Pro 4300 Manual de usuario

HP Workstation x1100 Manual de usuario

HP 205 G2 AiO Business Instrucciones de montaje

HP Kayak XU04 Hoja de especificaciones

HP Compaq Elite 8300 All-in-One Instrucciones de uso

HP Visualize c3600 Guía de inicio rápido

HP Vectra XE320 Manual del producto

HP Kayak XW U3-W3 Manual de lista de piezas

HP Pavilion t124 Instrucciones de instalación

HP 8000f - Elite Ultra-slim Desktop PC Manual

HP Compaq Evo d500 SFF Manual de usuario

HP Bc1500 - BladeSystem - Blade PC Instrucciones de funcionamiento y seguridad

HP Compaq dx2200 MT Series Manual de usuario

HP Pro 2000 Guía de configuración

HP Pavilion t700 - Desktop PC Manual de usuario

HP Pavilion a200 - Desktop PC Instrucciones de instalación

HP Compaq dc5750 SFF Manual

HP Vectra VEi 7 Manual

HP Vectra VLi 8SF Manual

HP Presario S7000 - Desktop PC Manual de usuario

HP ENVY 795 Instrucciones de instalación

HP dx2450 - Microtower PC Guía de configuración

HP A320m - Pavilion - 256 MB RAM Instrucciones de instalación

Manuales populares de De oficina de otras marcas

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario

Everex

Everex eXplora Manual de usuario

Lenovo

Lenovo ThinkCentre M75e Manual de usuario

Dell

Dell Alienware Area-51 R4 Manual de usuario